BMW Engine Parts for BMW 3 Series E46 (1999-2005)

If your M50, M52, or M54 engine takes a few seconds to build oil pressure after sitting, there's a good chance that your factory oil filter housing drain back valve has failed. Over time, the factory plastic check valve degrades, allowing oil to drain completely out of the housing and back into the oil pan while sitting. Every cold start essentially becomes a dry start, resulting in a loud ticking noise and causing unnecessary wear on your engine's internals.

Unfortunately, BMW does not offer this check valve as a standalone part, forcing you to purchase a costly, complete oil filter housing assembly just to fix one failed plastic component. Thankfully, our team of BMW enthusiasts took note of this common failure mode and designed a permanent, cost-effective fix.

Our Billet Oil Filter Housing Drain-Back Valve is designed as a direct-fit upgrade for your factory oil filter housing. CNC-machined from high-strength billet aluminum, this upgraded valve restores positive sealing to keep the oil filter housing fully primed. Maintaining this hydraulic prime ensures rapid oil pressure stabilization upon startup, directly mitigating dry-start bearing wear and top-end lifter starvation without requiring the purchase of a complete OEM housing assembly.

The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.

Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.

Features & Benefits:

Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program!

Take the guesswork out of S54 ownership. This all-inclusive kit targets the two most notorious failure points on the BMW S54 engine: broken exhaust hub tabs and degraded internal seals.

Turner Motorsport S54 VANOS Exhaust Hub Upgrade

The factory S54 exhaust hub is a ticking time bomb. Excessive play between the drive tabs and the oil pump disk creates a rhythmic rattling that eventually shears the tabs off, risking catastrophic engine failure.

While other kits require deep-engine surgery, our Turner Motorsport Hub Upgrade offers a "work smarter" approach.

Precision Engineering: Developed using 3D scanning and CAD modeling for a perfect, interference-free fit.

Superior Materials: Machined from high-strength 4340 steel and hardened to OEM specifications.

No Re-Timing Required: This bolt-on fix eliminates the failure point without the need to disassemble the VANOS unit or disturb engine timing, saving hours of labor.

ECS Tuning VANOS Seal Kit

The original BMW seals are made of Buna-N rubber, which quickly hardens and loses its sealing properties when exposed to synthetic oil and high heat. Our ECS engineering team has corrected this flaw.

Viton™ Upgrade: We utilize high-performance Viton O-rings for the internal seals, seal plate, and solenoid.

Chemical Resistance: These seals are designed to remain pliable and effective for the life of the engine, restoring lost low-end torque and smoothness.

ECS Tuning Rattle Repair Kit

Eliminate the dreaded "marbles in a can" sound. This kit addresses the axial play in the VANOS helical gears.

Hardened Steel: Our rings and washers are precision-ground to resist the wear and deformation that lead to engine rattle.

Silent Operation: Restores the refined sound and feel of your S54 across the entire RPM range.

The factory VANOS exhaust hub on the S54 engine is known to develop excessive play where the drive tabs interface with the oil pump disk. Over time, this imprecise fitment causes a back-and-forth rattling motion that can result in the tabs shearing off inside the engine, risking catastrophic damage or complete engine failure. Unlike other aftermarket solutions that require full VANOS disassembly, retiming, or replacement of the oil pump disk, the Turner Motorsport S54 VANOS Hub Upgrade offers a smarter approach. Our bolt-on fix eliminates the common failure point without opening the VANOS unit or disturbing engine timing.

Our solution involves removing the worn tabs from your stock exhaust hub and installing our precision-fit replacement, which is precision-machined from 4340 steel and hardened to meet OEM specifications. Designed using 3D scanning and CAD modeling, the Turner Motorsport VANOS Exhaust Hub Upgrade provides a tight, interference-free fit into the oil pump disc, completely resolving the issue without unnecessary labor.

Features & Benefits:

Direct bolt-on solution for S54 VANOS oil pump drive tab failure, preventing potentially catastrophic damage to engine internals Precision-machined from high-strength 4340 steel and heat-treated to match OEM specifications Designed using 3D scanning and CAD modeling to ensure precise fitment within the OEM oil pump disc Engineered to eliminate the play that exists between the exhaust hub and oil pump disc from factory Backed by extensive real-world testing and our lifetime replacement program! Kit Contents:

Turner Motorsport Exhaust VANOS Hub Upgrade 4x Extended Length Hex Head Bolts (M6x30 Gr. 10.9) 8x OEM BMW VANOS Hub Hex Head Bolts (M6x25) 12x Fillister Head Torx Screw (M6x16) OEM Valve Cover Gasket OEM VANOS to Cylinder Head Gasket

Whether you are building a high-performance engine or simply performing a routine rebuild, getting your piston ring end gaps and installation right is critical for optimal engine performance, compression, and longevity. Designed to meet strict standards, this comprehensive toolset provides everything you need to file, measure, and install piston rings safely without causing damage.

KIT CONTENTS

Schwaben Piston Ring Filer

Easily modify piston rings for OEM engine rebuilds and boosted applications Cuts quickly and smoothly, allowing you to easily avoid filing in excess Durable, bench-mountable construction with a long-lasting diamond abrasive wheel Piston Ring Installation Tool

Ensures even tension distribution during expansion Accommodates all pistons ranging from 60 mm to 175 mm in diameter Features an easy thumb-release locking mechanism for quick and secure operation Feeler Gauge Set

16 blades - 0.002-0.025 inch thickness measurements