BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Athena Cut Ring Head Gasket - 84.5mm - BMW M50 M52 (84mm Bore) ...

T#:26171655

Part#: ATH-HG-CR-M50-84

Ships in 7 Business Days

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Upgrade your BMW engine's performance with the Athena Cut Ring Head Gasket. This gasket replaces BMW part # 11121726619 and 11121726617 and is specifically designed for M50 & M52 iron block inline 6-cylinder engines found in E34/E36 chassis. Standard OEM & MLS gaskets can only handle a certain amount of cylinder pressure before they start to leak, making the Athena Cut Ring Head Gasket the recommended choice for applications making 16+ psi. A compression leak passing the head gasket can cause a range of issues, including engine overheating, loss of power, misfires, and in severe cases, catastrophic engine failure. Athena's gasket is crafted with premium quality reinforced M0115, an asbestos-free material that's original equipment approved and renowned for its superior quality. The AISI 304 stainless steel Cooper Rings bite into the aluminum head, providing maximum sealing capabilities around the cylinder bore and optimizing engine performance, even on engines with nitrous and/or turbo applications that exceed 2-bar boost. Before installation, it is crucial to have the mating surfaces of the cylinder head and block professionally cleaned and resurfaced to ensure they are completely flat. Please be aware that the gasket should have a size that is 0.5mm to 1mm larger than the piston. For example, if the piston measures 84mm, then the gasket should be the next size up, either 84.5mm or 85mm. Installation instructions: Make sure that the engine block and cylinder head surfaces are clean, flat, and free from any debris, oil, or coolant. Install the Cut Ring gasket on the engine block and ensure that it is properly aligned. Avoid twisting or bending the gasket during installation. Place the cylinder head on top of the gasket and install the head bolts or studs in their correct positions. Follow the manufacturer's recommended torque specifications and tighten the bolts or studs in the proper sequence to ensure even clamping force across the gasket. After the initial tightening, re-torque the head bolts or studs after the engine has been started and then allowed to cool to room temperature. This will ensure that the gasket is properly seated and compressed. It is recommended to not use any additional sealant on the MLS gasket, as it is already coated with a Viton rubber sealant. Using additional sealant can hinder the performance of the gasket.

Show More Show Less

5150 AutoSport S54 VANOS Hub

T#:35154980

Part#: 5150-VANOS

Back Ordered

$ 679.99 USD

Add to Wish List

Qty

$ 679.99 USD

Add to Wish List

Schrick - S54 Exhaust Camshaft (280 Degree, 12.5mm Lift) - E46 M3, Z3...

T#:1259

Part#: TMS1259

In Stock

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Performance Rod Bearing Kit - S54

Early Model S54 Engines up to 02/2003 production date

T#:26171617

Part#: 5150-HPRBK-S54-E

Back Ordered

$ 669.99 USD

Add to Wish List

Qty

$ 669.99 USD

Add to Wish List

Now one of 5150's best sellers has gotten even better! With a 5150 Autosports' complete High-Performance Rod Bearing Kit, you get all the parts you need to easily swap out the factory connecting rod bearing shells and bolts in one simple kit. 5150's S54 bearings are embraced by BMW engine builders worldwide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical. Proven by customers to help you finish the race even with loss of oil pressure! Kit includes: (1) Complete set of ARP S54 Connecting Rod Bolts (1) Complete set of 5150 High Performance Rod Bearing Set (1) ARP Assembly Lubricant packet Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

Schrick - S54 Intake Camshaft (288 Degree, 12.5mm Lift)- E46 M3, Z3M,...

T#:3572

Part#: TMS3572

Ships on Dec 18, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:338216

Part#: TMS1259

Ships on Mar 3, 2027

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick - S52/M52 Exhaust Camshaft (256 Degree/10.6mm Lift) E36 M3, Z...

T#:300485

Part#: 261.A1.561-02.C

In Stock

$ 1,401.99 USD

Add to Wish List

Qty

$ 1,401.99 USD

Add to Wish List

Performance Rod Bearing Set - M5X

T#:26171648

Part#: 5150-HPRBS-M50

Ships in 3 Business Days

$ 219.99 USD

Add to Wish List

Qty

$ 219.99 USD

Add to Wish List

5150 High-Performance Coated Rod Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market. Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended.

Show More Show Less

Performance Main Bearing Set - S54

T#:26171616

Part#: 5150-HPMBS-S54

Ships in 3 Business Days

$ 343.99 USD

Add to Wish List

Qty

$ 343.99 USD

Add to Wish List

5150 High-Performance Coated Main Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

BMW M54 Main Bearing Performance Set

T#:26171610

Part#: 5150-HPMBS-M54

Ships in 3 Business Days

$ 343.99 USD

Add to Wish List

Qty

$ 343.99 USD

Add to Wish List

BMW M54 Main Bearing Performance Set is engineered to meet the rigorous demands of high-performance engine builds. Designed by Turner Motorsport, these high-performance coated main bearings offer enhanced durability and efficiency for engines subjected to extreme conditions.

High-Performance Coating: Treated with a specialized coating by Calico, these bearings reduce friction and prevent "spinning" under high stress, making them ideal for high-power applications.
Enhanced Power Generation: The coating allows the engine to generate more power while maintaining reliability, even under demanding conditions.
Thermal Resistance: Built to withstand high temperatures and perform effectively in forced induction and race applications, these bearings help prevent engine failure due to oil pressure loss.
Proven Durability: Tested extensively on and off the track, 5150 bearings are known for their longevity and superior performance compared to other bearings on the market.

Upgrade to the BMW M54 Main Bearing Performance Set from Turner Motorsport for a robust solution that enhances engine reliability and performance.

Show More Show Less

Performance M5X Main Bearing Set

T#:26171649

Part#: 5150-HPMBS-M50

Ships in 3 Business Days

$ 299.99 USD

Add to Wish List

Qty

$ 299.99 USD

Add to Wish List

5150 High Performance Coated Main Bearing Sets are made for the demands of high performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use, but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market. Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended.

Show More Show Less

Schrick - S54 Intake Camshaft (280 Degree, 12.5mm Lift)- E46 M3, Z3M,...

T#:11748

Part#: TMS11748

Ships on Dec 18, 2026

$ 1,867.99 USD

Add to Wish List

Qty

$ 1,867.99 USD

Add to Wish List

E46 M3 with S54 engine Schrick 280 Degree Intake Camshaft with 12.5mm valve lift. A new rocker arm is required (Schrick or new BMW part #11337833259).

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E46 325, 330, 530, X5 3.0, Z3 3.0 - 264/248 ...

T#:4048

Part#: E46-M54-SCHRICK

Ships on Mar 3, 2027

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

Schrick 264 degree (10.5mm lift) intake and 248 degree (10mm lift) exhaust cams provide a power boost at mid-high RPM range without software changes. As used in our 330i ZHP Project Car! These are also available for track / race applications in 272 intake and 256 exhaust durations. We also recommend purchasing Supertech High Performance Valve Springs Call us for details. Professional installation required for all Shrick Camshafts.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

Show More Show Less

Schrick Solid Lifter Conversion Kit (convert Hydraulic Lifters To Sol...

T#:359938

Part#: 086311700KT

Ships on Mar 3, 2027

$ 833.52 USD

Add to Wish List

Qty

$ 833.52 USD

Add to Wish List

One major hurdle for a track-only car is the limitation of the hydraulic valve lifters in the M50, S50-US, M52, S52-US, M52TU, and M54 engines. These effectively limit your revs to 7200-7300 RPM as the valves 'float' at higher revs, leading to piston-valve contact. By converting to a machined solid lifter, and upgrading other areas of the engine, you can configure the valve train to withstand high RPM running. Not only can you tune for more power, you can help prevent damage during a mild mechanical over-rev.

This kit includes the mechanical spacers to convert hydraulic lifter tappets to solid lifters. The lifter bucket remains in place with the Schrick solid tappet replacing the original. These work on all M50, M52, S50, S52 and M54 engines and were proven in normally aspirated as well as supercharged engines. A custom camshaft is required.

Professional installation and setup is mandatory as these require complete assembly of the head, checking valve lash, then dis-assembly and machining of the Schrick tappet to spec. This kit includes enough spacers for 24 valves. We also carry individual parts, if you are looking for single pieces. This price is for a full set of 24.

Show More Show Less

Schrick - S52/M52 Intake Camshaft (264-Degree/11.2mm Lift) - E36, E39...

T#:300487

Part#: 261.E1.641-V2C

Ships on Dec 18, 2026

$ 1,398.99 USD

Add to Wish List

Qty

$ 1,398.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the S50 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Intake - 264 Duration Intake @ 1mm - 227 Intake Peak Timing - Cam Lobe Lift Intake - Valve Lift w/o Valve Clearance Intake - Valve Clearance Intake -

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 12.5mm Lift ...

T#:201497

Part#: TMS201497

Ships on Dec 18, 2026

$ 3,551.99 USD

Add to Wish List

Qty

$ 3,551.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW S52/M52 6 Cyl. 256-Degree - Exhaust Camshaft

T#:637317

Part#: 0261A1561-02

Special Order: No Guaranteed ETA

$ 1,619.99 USD

Add to Wish List

Qty

$ 1,619.99 USD

Add to Wish List

Schrick has been dedicated to engine performance through the development of only the highest-quality camshafts for more than 40 years. They've created a bond with BMW enthusiasts nearly the entire time, offering options for both the street and track using top materials for strength and accuracy. Schrick has grown into a technology center offering one of the most advanced locations for engine testing and manufacturing. These are the same cams used by many high-end German tuners who are achieving sizeable gains with the M52 and S52 engines. For the power-hungry, these cams are a great way to achieve a linear increase in horsepower from mid-range, up to redline. Duration Exhaust- 256 Duration Exhaust @ 1mm - 227 Exhaust Peak Timing - Cam Lobe Lift Exhaust - Valve Lift w/o Valve Clearance Exhaust - Valve Clearance Exhaust -

Show More Show Less

Schrick Exhaust Camshaft

T#:349689

Part#: 0261A1561-DV0

Special Order: No Guaranteed ETA

$ 1,721.99 USD

Add to Wish List

Qty

$ 1,721.99 USD

Add to Wish List

Schrick exhaust camshaft

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 280/272 12.5mm Lift ...

T#:338745

Part#: E46M3SCHRICK

Ships on Dec 18, 2026

Starting at $ 2,692.99 USD

Add to Wish List

Starting at $ 2,692.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These proved to be an excellent upgrade on our first Project E46 M3 and very similar to the stock E46 M3 CSL cams. Smooth as stock idle with a linear increase in horsepower from midrange all the way to redline. Peak gain was 15hp with no loss in low end torque. The duration of the intake cam is 280 and the exhaust is 272 with 12.5mm valve lift. These are the new "cast" cams from Schrick which require new rocker arms (Schrick or BMW part #11337833859). Professional installation is a must due to the intricacies with the double VAN0S.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick - S54 Exhaust Camshaft (272 Degree, 12.5mm Lift)- E46 M3, Z3M...

T#:11749

Part#: TMS11749

Ships on Dec 18, 2026

$ 824.99 USD

Add to Wish List

Qty

$ 824.99 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 12.5mm Lift ...

T#:340423

Part#: TMS201497

Ships on Dec 18, 2026

Starting at $ 3,551.99 USD

Add to Wish List

Starting at $ 3,551.99 USD

Add to Wish List

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

BMW S54 3.2L Schrick Camshaft Set 280/272 12.5mm Lift

T#:3855

Part#: E46M3SCHRICK

Ships on Dec 18, 2026

$ 2,692.99 USD

Add to Wish List

Qty

$ 2,692.99 USD

Add to Wish List

SEE T#338745 BMW S54 3.2L Schrick Camshaft Set 280/272 12.5mm Lift is the perfect performance upgrade for enthusiasts seeking to enhance their engine's capabilities. With over 40 years of experience, Schrick is dedicated to producing high-quality camshafts that deliver exceptional power and reliability. Designed for both street and track applications, these camshafts offer an impressive balance of performance and drivability. The intake cam features a duration of 280, while the exhaust cam has a duration of 272, with a valve lift of 12.5mm. These new "cast" cams from Schrick closely resemble the stock E46 M3 CSL cams, ensuring a smooth idle and a significant increase in horsepower throughout the RPM range. With a peak gain of 15 horsepower and no loss in low-end torque, these camshafts are a top choice for BMW enthusiasts.

Key Benefits:

Enhanced Power: Delivers a peak gain of 15 horsepower.
Smooth Idle: Maintains a factory-like idle quality for everyday driving.
Linear Power Increase: Provides a steady increase in horsepower from midrange to redline.
Compatibility: Designed to fit the BMW S54 engine with new rocker arms required.
High-Quality Construction: Crafted from top materials for strength and durability.

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 296 Degree, 12.5m...

T#:338218

Part#: 0415A1960-00

Back Ordered

Starting at $ 829.00 USD

Add to Wish List

Starting at $ 829.00 USD

Add to Wish List

E46 M3 Schrick 296 Degree Exhaust Camshaft with 12.5mm lift. This cam is much more aggressive than either of the "standard" Schrick exhaust cams. A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 272 Degree, 12.5m...

T#:338215

Part#: TMS11749

Ships on Dec 18, 2026

Sale - Save 29% $ 3,042.99

This product was last offered at the strikethrough price on
11-07-2026

Starting at $ 2,165.97 USD

Add to Wish List

Sale - Save 29%

$ 3,042.99

This product was last offered at the strikethrough price on
11-07-2026

Starting at $ 2,165.97 USD

Add to Wish List

E46 M3 Schrick 272 Degree Exhaust Camshaft with 12.5mm valve lift. New rocker arms are required (BMW part #11337833259 or a new Schrick part).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Oil Pump Upgrade Kit - M50/M52/S50/S52

T#:26204983

Part#: 5150-OPUK-M50

Back Ordered

$ 229.99 USD

Add to Wish List

Qty

$ 229.99 USD

Add to Wish List

The M50/M52/S50/S52 engines are notorious for their well-documented problems stemming from harmonics. The vibration leads to the oil pump shaft becoming weak, causing it to either break or the oil pump nut to loosen and fall off, resulting in an immediate loss of oil pressure. Worry no more! 5150 has the solution! At the core of this kit is a hardened Chromoly shaft, meticulously centerless ground to guarantee absolute precision. This shaft is designed with an exclusive square key lock system, which not only prevents the gear from ever rotating on the shaft but also reinforces the mounting area, adding additional strength. Furthermore, we replaced the problematic oil pump nut with an extended-length bolt, which is EDM drilled to accommodate safety wire for a secure fit in all conditions. Don't wait until your oil pump fails, leaving you facing expensive engine repairs! Key Features: Centerless ground shaft made from hardened Chromoly. Bolt with EDM drilling, including safety wire. Grade 8 extended-length hardware for secure gear attachment. Left-hand threaded to prevent unexpected loosening. Double-D keyed shaft and drive gear. Fully serviceable and rebuildable without the need for grinding.

Show More Show Less

Performance Rod Bearing Kit - S54

For Late Model S54 Engines after 02/2003 production

Late Model: S54 Engines after 02/2003 production and later use M10 Bolts.

T#:26171618

Part#: 5150-HPRBK-S54-L

Back Ordered

$ 529.99 USD

Add to Wish List

Qty

$ 529.99 USD

Add to Wish List

Now one of 5150's best sellers has gotten even better! With a 5150 Autosports' complete High-Performance Rod Bearing Kit, you get all the parts you need to easily swap out the factory connecting rod bearing shells and bolts in one simple kit. 5150's S54 bearings are embraced by BMW engine builders worldwide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical. Proven by customers to help you finish the race even with loss of oil pressure! Kit includes: (1) Complete set of ARP S54 Connecting Rod Bolts (1) Complete set of 5150 High Performance Rod Bearing Set (1) ARP Assembly Lubricant packet Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

BMW M50 M52 S50 S52 Cut Ring Head Gasket

T#:45176130

Part#: ATH-CR330014

Back Ordered

$ 324.99 USD

Add to Wish List

Qty

$ 324.99 USD

Add to Wish List

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 12.5mm...

T#:338222

Part#: TMS3572

Ships on Mar 3, 2027

Sale - Save 63% $ 5,600.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 2,068.04 USD

Add to Wish List

Sale - Save 63%

$ 5,600.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 2,068.04 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

CP-Carrillo Connecting Rod Set M5X Pro-Xtreme

T#:26204921

Part#: CAR-CRS-S52-XT

Ships in 3 Business Days

$ 2,099.99 USD

Add to Wish List

Qty

$ 2,099.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW M50 Non-VANOS, M52, S50, S52, and M54 engines with 135 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines. Please note that these 135 mm connecting rods are designed to fit M50 Non-VANOS, M52, M52TUB28, S50 U.S, S52 U.S, and M54B30 135mm Rod engines. They will NOT fit M50-VANOS engines, as they require 140 mm Rods.

Show More Show Less

Performance Rod Bearing Set - M54

T#:26171611

Part#: 5150-HPRBS-M54

Ships in 3 Business Days

$ 251.99 USD

Add to Wish List

Qty

$ 251.99 USD

Add to Wish List

5150 High-Performance Coated Rod Bearing Sets are made for the demands of high-performance engine builds. Treated shells and coated by Calico to reduce friction, these bearings allow your engine to generate more power and resist "spinning" under stress. These coated bearings also have thermal resistant properties that not only perform in high HP applications like forced induction or race use but also help prevent sudden engine failure in the event of oil pressure loss. 5150 bearings have proven themselves on and off the track, lasting longer and outperforming other bearings on the market.

Show More Show Less

CP-Carrillo Connecting Rod Set - S54

Upgrade Your Connecting Rods in Your High Horsepower S54!

T#:26171622

Part#: CAR-S54-SCR

Ships in 3 Business Days

Starting at $ 2,149.99 USD

Add to Wish List

Starting at $ 2,149.99 USD

Add to Wish List

CP-Carrillo's connecting rods for the BMW S54 engine are specifically engineered to serve as direct replacements for BMW part numbers #11247834437, #11247831924, #11247834310, and 11247831331 in the BMW S54B30, S54B32, S54B33, S54B34, and S54B35 engines, with a length of 139 mm. These Carrillo connecting rods boast a range of impressive features: Crafted from a special chrome-moly based alloy, ensuring strong and durable forged rods. Their lightweight design significantly reduces mass compared to standard rods, optimizing engine performance. These rods have demonstrated exceptional strength and performance in racing environments, vouching for their reliability. Carrillo maintains stringent quality control measures, resulting in tight tolerances and precision balancing for superior performance. Each set is meticulously matched and balanced, ensuring consistent and smooth operation. The connecting rods come equipped with high-quality, non-stretch WMC rod bolts, guaranteeing stability under high-stress conditions. For those seeking even higher performance, there is an option to upgrade to CARR bolts. In conclusion, Carrillo connecting rods stand as the top choice for racers who demand the utmost in performance and reliability from their engines. With a track record of excellence and a suite of advanced features, these rods are the epitome of quality and precision for high-performance applications.

Show More Show Less

5150 AutoSport High Performance Rod Bearing Set - N54

T#:38419052

Part#: 5151-HPRBS-S54

Ships in 3 Business Days

$ 399.99 USD

Add to Wish List

Qty

$ 399.99 USD

Add to Wish List

Upgrade your BMW S54 engine with the 5150 AutoSport High Performance Rod Bearing Set—a premium solution designed to improve durability, reliability, and longevity. This high-performance bearing set addresses the well-known rod bearing wear issues found in the E46 M3, Z3M, and Z4M engines, offering superior materials and precision engineering for high-RPM and high-load applications. Product Features: Advanced Materials – Manufactured from tri-metal or bi-metal alloys, these bearings provide superior wear resistance and strength under extreme conditions. Optimized Oil Clearance – Precision tolerances ensure proper oil flow and lubrication for maximum engine performance. Proven Durability – Built for motorsport, high-performance street use, and endurance applications, ensuring long-lasting reliability. OEM Replacement – Designed to fit factory specifications for an easy, direct installation with no modifications needed. Prevention of Bearing Failure – Helps mitigate the risk of premature rod bearing failure, a common issue in the S54 engine. For optimal performance, we recommend pairing these bearings with ARP rod bolts and an upgraded oil pump to further enhance engine protection and longevity.

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 14.0m...

T#:338217

Part#: TMS201495

Ships on Mar 3, 2027

Starting at $ 3,804.99 USD

Add to Wish List

Starting at $ 3,804.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 14.0mm valve lift. This is only for use in professionally-built E46 M3 race engines. Schrick has developed this ultra-aggressive S54 race cam with 280-deg duration and 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends it be used with special custom pistons with deep valve reliefs. We strongly recommend this be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with this cam:
Schrick valve springs
Schrick rocker arms
Schrick upper and lower retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 288/280 14mm Lift ...

T#:340424

Part#: TMS200186

Back Ordered

Starting at $ 3,261.73 USD

Add to Wish List

Starting at $ 3,261.73 USD

Add to Wish List

E46 M3 Schrick high-performance racing camshaft set - 288 degree intake and 280 degree exhaust. These camshafts are for use in professionally-built E46 M3 race engines. Schrick has developed these ultra-aggressive S54 race cams with 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends them be used with special custom pistons with deep valve reliefs. We strongly recommend these be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with these cams:
Schrick valve springs
Schrick rocker arms
Schrick upper (titanium) and lower (steel) retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Camshaft Set - E46 323/328 M52TU - 248/248

T#:773

Part#: E46M52TUSCHRICK

Ships on Mar 3, 2027

$ 2,915.38 USD

Add to Wish List

Qty

$ 2,915.38 USD

Add to Wish List

M52TU Schrick Camshaft Set. 248 degree 10mm lift intake, 248 degree exhaust. Great for street use. Power gains across the board with calm idle. No need for upgraded valve train. Works perfect for 323 / 328!

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
1999-2000 E46 BMW 323i 323ci 328i 328ci
1999-2000 E39 BMW 528i
1999-2000 Z3 BMW Z3 2.3 Z3 2.8

Show More Show Less

Schrick Camshaft Set - E46 M3, MZ3, MZ4 (S54) - 304/296 14mm Lift ...

T#:340425

Part#: TMS200183

Ships on Mar 3, 2027

Starting at $ 4,865.48 USD

Add to Wish List

Starting at $ 4,865.48 USD

Add to Wish List

E46 M3 Schrick high-performance racing camshaft set - 304 degree intake and 296 degree exhaust. These camshafts are for use in professionally-built E46 M3 race engines. Schrick has developed these ultra-aggressive S54 race cams with 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends them be used with no VAN0S and with special custom pistons with deep valve reliefs. We strongly recommend these be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with these cams:
Schrick valve springs
New Schrick or BMW rocker arms
Schrick upper (titanium) and lower (steel) retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 304 Degree, 12.5mm...

T#:338220

Part#: 0415E1040-00

Ships on Mar 3, 2027

Starting at $ 829.00 USD

Add to Wish List

Starting at $ 829.00 USD

Add to Wish List

E46 M3 Schrick 304 Degree Exhaust Camshaft with 12.5mm lift. This cam is much more agressive than the "standard" Schrick intake cams. A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Camshaft Set - S54 288/280 14mm Lift

T#:200186

Part#: TMS200186

Back Ordered

$ 3,261.73 USD

Add to Wish List

Qty

$ 3,261.73 USD

Add to Wish List

NOW LOCATED UNDER T#340424

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 304 Degree, 14.0mm...

T#:338221

Part#: TMS201493

Ships on Mar 3, 2027

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 304 Degree Intake Camshaft with 14.0mm valve lift. This is only for use in professionally-built E46 M3 race engines. Schrick has developed this ultra-aggressive S54 race cam with 304-deg duration and 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends it be used with no VAN0S or with special custom pistons with deep valve reliefs. We strongly recommend this be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with this cam:
Schrick valve springs
Schrick rocker arms
Schrick upper and lower retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 296 Degree, 14.0m...

T#:338219

Part#: TMS201492

Ships on Mar 3, 2027

Sale - Save 45% $ 7,065.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 3,897.86 USD

Add to Wish List

Sale - Save 45%

$ 7,065.99

This product was last offered at the strikethrough price on
07-08-2026

Starting at $ 3,897.86 USD

Add to Wish List

E46 M3 Schrick 296 Degree Exhaust Camshaft with 14.0mm valve lift. This is only for use in professionally-built E46 M3 race engines. Schrick has developed this ultra-aggressive S54 race cam with 296-deg duration and 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends it be used with no VAN0S or with special custom pistons with deep valve reliefs. We strongly recommend this be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with this cam:
Schrick valve springs
Schrick rocker arms
Schrick upper and lower retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Intake Camshaft - E46 M3, MZ3, MZ4 (S54) - 288 Degree, 14.0mm...

T#:338223

Part#: TMS201494

Back Ordered

Starting at $ 829.00 USD

Add to Wish List

Starting at $ 829.00 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 14.0mm valve lift. This is only for use in professionally-built E46 M3 race engines. Schrick has developed this ultra-aggressive S54 race cam with 288-deg duration and 14mm of valve lift. Because of the aggressive profile and specs of this cam, Schrick only recommends it be used with special custom pistons with deep valve reliefs. We strongly recommend this be professionally installed by an experienced engine builder to check clearances and fitment.

Schrick also requires valvetrain hardware to go along with this cam:
Schrick valve springs
Schrick rocker arms
Schrick upper and lower retainers

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster, Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster, Z4 M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 14.0m...

T#:23847549

Part#: 0415A180001

Special Order: No Guaranteed ETA

$ 1,876.99 USD

Add to Wish List

Qty

$ 1,876.99 USD

Add to Wish List

CP-Carrillo Connecting Rod Set - S54 Pro-Xtreme

T#:26204927

Part#: CAR-CRS-S54-XT

Back Ordered

$ 2,299.99 USD

Add to Wish List

Qty

$ 2,299.99 USD

Add to Wish List

The 5150 AutoSport Pro-Xtreme Connecting Rods, made by CP-Carrillo, are designed to handle extreme horsepower and high RPM applications for BMW S54 engines with 139 mm Rods. Constructed from high-strength, aircraft-grade steel, these connecting rods are engineered to withstand the forces generated by high-powered engines. The Pro-Xtreme design is specifically tailored to handle up to 2000 horsepower, making these rods suitable for high-performance turbo/drag racing or street/strip applications. They are also designed to handle high engine speeds of up to 9500 RPM, which is necessary for achieving maximum power output. Each connecting rod is precisely fabricated to meet the demands of high-performance engines using advanced manufacturing techniques such as computer-aided design (CAD) and finite element analysis (FEA). The Pro-Xtreme Connecting Rods are designed to be durable, reliable, and capable of handling the extreme stresses and forces generated by high-horsepower and high-rpm engines.

Show More Show Less

CP-Carrillo Forged Piston Set - M54B28 Std. Size

For Vehicles With M54B25 Engine Only

T#:26071892

Part#: M54B25-CPP-84

Back Ordered

Starting at $ 2,206.98 USD

Add to Wish List

Starting at $ 2,206.98 USD

Add to Wish List

CP-Carrillo sets the benchmark for premium aftermarket forged pistons. Crafted with high-strength, lightweight materials and cutting-edge engineering, this BMW M54B25 piston set boasts the following features: Lightweight Design: Constructed from forged aluminum alloy, CP-Carrillo pistons offer reduced weight, enhancing engine responsiveness and acceleration for a dynamic driving experience. Advanced Engineering: Leveraging state-of-the-art technology, CP-Carrillo engineers optimize combustion, fuel efficiency, and power output, ensuring peak performance in every application. Wide Configuration Range: With a variety of bore sizes and compression ratios available, CP-Carrillo provides options to tailor pistons to specific engine builds and performance objectives. Quality Construction: Each CP-Carrillo piston undergoes precision machining and rigorous testing to meet exacting standards, guaranteeing consistent quality and performance in every set. Engineered by one of motorsport's most respected names, CP-Carrillo pistons are the ultimate choice for the M54B25 engine, whether for street performance or track dominance. Piston Sets Include: Pistons Rings Pins Locks Spec Sheet Optional Extras: Skirt Coating - Adding a Protective Layer Between the Sides of the Piston and Cylinder Walls Dome Coating - Adding a Protective Layer to the Top of The Piston HD-Wrist Pins - A Must if You are Planning on Going Beyond 850 HP! X Forging - Reducing Rotational Mass By Moving the Wristpin Inwards and Shortening it While Increasing Overall Strength Please Note: It is essential to have all engine modifications performed by a qualified professional to ensure proper installation and optimal engine performance, safety, and reliability.

Show More Show Less

CP-Carrillo Pro-Xtreme Forged Piston Set Std. Size - S54

T#:26171645

Part#: CP-FPS-S54-XT

Back Ordered

Starting at $ 2,268.98 USD

Add to Wish List

Starting at $ 2,268.98 USD

Add to Wish List

CP-Carrillo sets the benchmark for premium aftermarket forged pistons. Crafted with high-strength, lightweight materials and cutting-edge engineering, this BMW S54 piston set boasts the following features: Lightweight Design: Constructed from forged aluminum alloy, CP-Carrillo pistons offer reduced weight, enhancing engine responsiveness and acceleration for a dynamic driving experience. Advanced Engineering: Leveraging state-of-the-art technology, CP-Carrillo engineers optimize combustion, fuel efficiency, and power output, ensuring peak performance in every application. Wide Configuration Range: With a variety of bore sizes and compression ratios available, CP-Carrillo provides options to tailor pistons to specific engine builds and performance objectives. Quality Construction: Each CP-Carrillo piston undergoes precision machining and rigorous testing to meet exacting standards, guaranteeing consistent quality and performance in every set. Engineered by one of motorsport's most respected names, CP-Carrillo pistons are the ultimate choice for the S54 engine, whether for street performance or track dominance. Piston Sets Include: Pistons Rings Pins Locks Spec Sheet Optional Extras: Skirt Coating - Adding a Protective Layer Between the Sides of the Piston and Cylinder Walls Dome Coating - Adding a Protective Layer to the Top of The Piston HD-Wrist Pins - A Must if You are Planning on Going Beyond 850 HP! X Forging - Reducing Rotational Mass By Moving the Wristpin Inwards and Shortening it While Increasing Overall Strength Please Note: It is essential to have all engine modifications performed by a qualified professional to ensure proper installation and optimal engine performance, safety, and reliability.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Sub-Categories

Schrick Technical Information / Specs

Key Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results