BMW Engine Parts for BMW 1 Series E82 (2008-2013)

The N54/N55 are the powerhouses of BMW, one of the most common tuning platforms, and a fan favorite for spirited driving. Being an N54/N55 owner you know that oil temps can get out of hand leaving you with an anxious feeling and the needle a little too close to the red on your gauge cluster. What if you could get the oil flowing faster, maintain lower temperatures, and still have proper engine warm-up?

Upgrade your N54/N55 engine with our Billet oil cooler housing, replacing the underperforming factory-cast aluminum unit. Engineered for enhanced performance and a blended aesthetic, our Turner oil cooler housing features an OEM+ black anodized finish and our own engineered lower-temperature thermostat. Unlike makeshift solutions like thermostat bypass kits, our housing integrates an OE thermostat, ensuring a gradual yet expedited engine warm-up process, similar to factory settings but faster.

Out goes the factory 110-degree Celsius (230F) thermostat, replaced by our 70-degree Celsius (158F) counterpart. This new thermostat triggers oil flow a significant 72 degrees Fahrenheit earlier than the factory version. This early flow translates into prolonged lower oil temperatures for both the oil cooler and engine, maintaining a happier, healthier engine with consistently lower operating temperatures.

For N54 owners seeking to use the full potential of their tuned or modified engines, our upgraded housing and thermostat are must-have additions, especially for those who frequent the track or enjoy spirited drives on winding roads. Even if you're not pushing your motor to its limits, this upgrade significantly enhances reliability. With rising oil temperatures, the risk of oil breakdown rises, resulting in compromised lubrication, more engine deposits, and increased wear over time. Our solution addresses these concerns, protecting your engine's longevity and performance, regardless of your driving style.

For vehicles equipped with the factory oil cooler, our housing offers a multitude of advantages and is a direct replacement for the OEM unit. If your vehicle lacks a factory oil cooler, this presents an ideal chance to upgrade your setup with our housing, enabling the addition of a factory cooler for enhanced performance and increased reliability. Our primary objective is to maintain optimal oil temperatures, ensuring proper lubrication for the engine's internal components, in turn prolonging their lifespan.

Features:

Thermostat - 40 degrees Celsius/ 72 degrees Fahrenheit lower than the factory unit Billet aluminum to replace the raw cast aluminum factory housing Optional cooler capability for cars without an OEM oil cooler Utilizes the lower temp thermostat to circulate oil sooner rather than an always open solution which inhibits warm-up Combine with OEM oil cooler to add cooling capacity to your FBO N54/N55 or replace the stock housing for a cooling upgrade using your existing cooler Replaceable thermostat and gaskets for easy maintenance Quick easy installation Kit Contents:

N54/N55 Billet Thermostat Housing Billet thermostat cover Low-temp thermostat Thermostat spring Housing and thermostat cover gaskets 2 Oil cooler line O-rings (17222245358) Product Development:

Our upgraded oil cooler housing was designed, engineered, tested, and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.

Transform your N54-powered BMW with the Turner Motorsport B58 Ignition Coil Conversion Kit—the ultimate solution for ignition system reliability and performance. Designed to eliminate the notorious misfires and power loss caused by factory OE pencil-style ignition coils, this kit is a game-changer for stock and modified vehicles alike. Whether you're chasing more power or improved drivability, the B58 ignition coils deliver up to 2.3x more spark energy, unleashing the full potential of your engine.

Why upgrade? The answer is simple: B58 ignition coils outperform all other ignition upgrades on the market with unparalleled spark energy and reliability. Ideal for high-performance builds or daily drivers, this kit eliminates common ignition problems while supporting increased power demands from software tunes like MHD or BM3. Plus, with the included plug-and-play wiring harness and proprietary boots, installation is seamless—no cutting or splicing is required.

Features:

Up to 2.3x More Spark Energy: Maximizes overall performance, offering sufficient output for heavily modified engines.
Plug-and-Play Installation: Includes custom brackets, wiring harnesses, and boots designed for factory mounting locations—no modifications needed.
DME Compatibility: Compatible with factory engine management software for hassle-free integration.
Rugged Durability: Bolt-on brackets are precision-machined from 6061-T6 aluminum with a sleek black anodized finish for a premium look and long-lasting performance.
Proprietary Design: Boots feature a built-in 1k OHM resistor to prevent electrical contact failures commonly seen in other kits.
Kit Contents:

(6) Turner Motorsport B Series Ignition Coils for N554/N55
(6) Turner Motorsport B58 Ignition Coil Conversion Wiring Harnesses
(6) Turner Motorsport B58 Ignition Coil Conversion Brackets
Optional Kit Selections:

Spark Plugs:
Bosch ZGR6STE2 (OEM)
NGK 97968 (One Step Colder)
NGK 97506 (Two Steps Colder)
Spark Plug Socket:
Schwaben 14mm 12pt Magnetic Socket
Schwaben 14mm 12pt Swivel Socket
Turner Motorsport offers a comprehensive installation guide, including detailed removal instructions and high-resolution images.

Upgrade your engine build with Turner's WPC-treated Race Series Bearings, engineered for serious performance enthusiasts. Starting with ACL’s high-performance bearing shells, these Race Series bearings are built to withstand extreme RPMs and stress. Utilizing a "Duraglide" tri-metal construction and a high-strength overlay plate, these bearings offer superior oiling and heat resistance for high-RPM operation.

Our WPC-treated bearings take ACL’s already impressive design and enhance it even further. The WPC treatment process strengthens and smooths the bearing surface by firing high-speed, ultra-fine particles at the bearing shells, reducing friction and improving durability. This advanced surface treatment ensures smoother operation and improved heat dissipation, which are critical for any high-performance engine.

Key Features:

Duraglide Tri-Metal Construction: ACL's Race Series bearings feature a high-strength overlay for enhanced performance. Optimized Oiling: Designed to promote better oil flow during high-RPM conditions. Precise Fitment: Manufactured with OEM-level precision using micron tolerance machining. WPC-Treated for Strength: Surface treatment adds strength and reduces friction for improved engine performance. No Flash Plating: Allows for better heat transfer and bearing retention. Thermal Discharge Process: Smoother, stronger components through WPC’s unique thermal discharge technology. Enhanced Heat and Friction Resistance: Built to combat the biggest enemies of high-performance engines. Don’t settle for standard bearings—choose Turner Motorsport WPC-treated Race Series Bearings for the ultimate engine performance upgrade. Perfect for your next engine rebuild or rod bearing service!

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

*Still require a solid mount? Turner Motorsport solid engine and transmission mounts for N52/N54/N55 coming early July 2017.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55

There are a few reason having a catch can is an upgrade for a vehicle, from a separator system that no longer works to one that was never there. Modern day emissions regulations require the use of a closed crankcase ventilation (PCV) system to recirculate combustion blow-by gases from the crankcase back in to the intake to be burned.  Unfortunately, these blow by gases contain water vapor (which is a byproduct of combustion) and pick up oil mist from and the windage cloud and cam lubrication system as they travel through the crank case.  Due to less than 100% effective air/oil separation in the stock PCV system, some oil mist and water vapor gets carried back to the intake tract and over time cause oil deposits and carbon buildup in the intake manifold, intake ports, and on the back of intake valves.  All will eventually lead to poor performance and reduced fuel economy, and the presence oil mist can in the intake charge even increase the risk of engine damaging detonation. 

With direct injected engines this problem becomes more prevalent, and the N54 in your 135i or 335i is no exception.  We're seeing a lot of N54 powered cars with drivability and performance issues due to significant carbon buildup in the intake ports and backs of intake valves.  The “factory fix” is a walnut blasting service that commonly needs performed every 30,000 to 70,000 miles.  Don't be part of this statistic!  Our shop recommends an oil catch can be installed in-line in the PCV system to help reduce the build-up of performance robbing deposits and greatly reduce the need for costly walnut blasting service and related repairs in the future.

​ The catch can utilizes a strategically designed 4 chamber baffle plate system engineered to create multiple changes in the direction of airflow to cause oil droplets to fall out of suspension, maximizing the efficiency of the PCV air/oil separation.  A dipstick is integrated into the cap so you can monitor the oil level, and the can is easily serviced.  At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil.  The Turner Motorsport Oil Catch Can is CNC machined from billet 6061-T6 aluminum and with a stealthy black anodized finish for lasting durability and appearance, and includes everything needed for an OEM-like fully reversible installation. Another feature the Turner catch can has is the ability to add on a drain kit so you no longer have to fumble around getting the fill can out of a tight space. The drain can be run down to the belly pan of your car so draining can be done at the same time you change your oil or anytime in between.

*Click here for catch can instructions*

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• 8oz reservoir
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole - drain kit included!
• Passenger side mounting kit - Designed specifically for your N54!

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain hole can be used with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole (valve and hose sold separately, watch for our model specific drain kits!)

Boost your engine's capabilities with the Dinan N-Series Performance Ignition Coils - a vivid set of six in striking red. Precision-engineered to amplify ignition power, these coils guarantee heightened throttle response, seamless idling, and a notable surge in overall power. Meticulously crafted for durability, they seamlessly integrate into your vehicle, enhancing both performance and aesthetic appeal under the hood.

Introducing the BMW N52, N54, N55, and S55 Race Series High-Performance Con Rod Bearing Set by Automotive Components Limited. Elevate your BMW's performance with these precision-engineered con rod bearings, specifically designed for performance BMW engines.

Key Features:

Premium Quality: Crafted with the utmost precision and durability, this con rod bearing set ensures high performance and reliability for your BMW. Race Series Design: Engineered to meet the demands of race applications, these bearings are well-suited for high-performance driving scenarios. Enhanced Engine Protection: The bearings provide essential protection for your engine components, ensuring their longevity even under extreme conditions. Perfect Fit: Designed to seamlessly fit BMW N52, N54, N55, and S55 engines found in many newer BMWs, these bearings are a direct replacement for your stock components. Improved Performance: Experience enhanced engine performance and responsiveness, making it ideal for racing and high-performance driving. Upgrade your BMW with the Race Series High-Performance Con Rod Bearing Set from Automotive Components Limited. Enhance your vehicle's performance and enjoy peace of mind knowing your engine is protected by top-quality components.