BMW Suspension Parts for BMW E92 M3 S65 4.0L

These M3 rear guide rod arms are an upgrade for the non-M cars. The stock non-M arms are made from sheetmetal spot welded together at the ends. The arm tends to flex and bend under even moderate cornering loads. Factor in gripper tires and more torque and this arm is inadequate for stability and consistent handling. The M3 arms are one piece of aluminum offering greater strength and with a sealed monoball inner bushing that allows the arm to rotate (instead of twisting).

This package includes:

• Left M3 Guide Rod - 33322283547
• Right M3 Guide Rod - 33322283548

• 52% stiffer than the factory E90/E92 M3 bar. 42% stiffer than the E93 M3 bar!
• 27mm straight across (not a tapered center like the E93 M3 factory bar)
• Solid core, not hollow like the stock bars (better at resisting twist)
• Forged, non-adjustable steel ends
• Highest tensile steel strength available

The H&R for the E9X M3 is the best anti-roll bar option for the E9X M3. Don't be let down by the "small" size compared to the factory sway bar sizes - there are some big differences! We've had our in-house suspension engineers run the math and the H&R swaybar is over 52% stiffer than the factory E90/E92 M3 bar and even over 42% stiffer than the E93 M3 sway bar upgrade. There are several reasons for this - the stock sway bars are hollow (for lighter weight) and will twist more than the solid H&R bar. Also, the E93 M3 bar is often called a 28mm bar but it actually tapers down in the center to 24mm which greatly reduces its effectiveness. So if you're looking for a serious sway bar upgrade, the H&R is clearly the way to go. Note: to maintain the handling balance of the car, we recommend only using the front bar with the matching H&R rear bar or heavily revised racing suspension.

For a more in-depth analysis of the E9X front sway bar differences, check out our FAQ!

This bar re-uses the factory M3 sway bar bushings and brackets.

This item fits the following BMWs:
2011+ E82 BMW 1M Coupe
2008+ E90 BMW M3
2008+ E92 BMW M3

When an E9X is lowered beyond the limits of just lowering springs, the rear wheels toe-in excessively. This excessive rear toe leads to premature wear, that many people attribute to an increase in negative camber. It has become a common belief that an extremely low vehicle will wear the tires wrong as a matter of consequence. It has become standard practice to go as low as you can and proceed to replace your tires every five to ten thousand miles. Whats more is that when the vehicle reaches a certain ride height, the factory arms become maxed out and there is no way to compensate and dial in the proper toe. You're left with an improperly aligned vehicle that is in effect worse off than it was with the stock suspension installed.

This is not only uneconomical but improper and unsafe. ECS Tuning is proud to offer a solution for this problem in the form of Rogue Engineering E9X adjustable rear toe arms. These arms allow for greater toe adjustment on vehicles that have been lowered with a coilover suspension. With the toe set properly the tires can contact the road properly this maximizes grip and minimizes wear. 

Features:

• 100% machined and anodized, 6061-T6 lightweight aluminum arms
• High-strength, 3-piece, rod end (with carbon fiber reinforced, PTFE race) offers longer life for street compared to standard rod ends
• SEALS-IT Rod end seals keep dirt, water, and other contaminants out
• Rod ends feature grease fittings, to allow for rod end serviceability.
• Lighter than stock!  (Stock is 875g, RE arms are 640g)
• Extremely easy installation and adjustment (your alignment shop will LOVE you!)

The Bilstein B8 Performance Plus Kit includes two front struts and two rear shocks. These shocks are for use with lowered springs such as from H&R or Eibach. We do not recommend that you use them with any factory spring, including factory sport package springs. With the increased damping rates from stock you will have much more control over body motions. These will give a much more buttoned down and taut feeling with lowering springs compared to stock shocks.

These shocks fit the following BMWs:

2007+ E90 Sedan M3 - not for cars with EDC
2007+ E92 Coupe M3 - not for cars with EDC

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Subframe Bushings
Diff Bushings
Control Arms & Bushings
Sway Bar End Links
Hardware