BMW Camber / Caster Kits for BMW E92 M3 S65 4.0L

Clear BMW chassis
The camber setting in your alignment is one of the most crucial aspects of your suspension and the overall driving experience. Unfortunately, most BMWs do not have a camber adjustment in the front and a limited adjustment in the rear. This can be frustrating because camber comes into play whenever you make changes to the suspension or when you want more negative camber for more grip and better handling. There are multiple reasons to adjust camber -

• You want more front end grip to reduce understeer and create a more balanced handling scenario,
•  You have lowered the car and need to reduce negative camber due to inside tire wear
•  You added wider tires or wheels and need extra clearance to bodywork,
•  Your car was in an accident or collision and the camber setting is now wrong. Note: there may be other factors to this situation and we recommend finding the root cause rather than a quick-fix.

We offer front fixed or adjustable camber plates or camber/caster plates, rear adjustable camber arms, and rear adjustable camber bushings from KMAC, Vorshlag, and also our own designs to fit your specific needs. In most cases, these adjustable camber kits are a direct replacement for the stock BMW part, enabling a seamless upgrade. Adjustable camber can be dialed-in using ordinary hand tools and most kits have reference marks for consistent and repeatable adjustments. No drilling, slotting, or welding required! Some kits perform specific functions and fit with specific types of suspensions (stock, stock-type, coil-over, etc). Give us a call if you need guidance in selecting the best camber plate option for your particular suspension or situation.

Turner Hybrid Camber & Caster Plates - E90 E92 E93 M3
Turner Hybrid Camber & Caster Plates - E90 E92 E93 M3
Featuring spherical monoball bearing for full shaft articulation!
Turner Motorsport - Corporate Logo
T#:568607
Part#: 003407TMSKT1
In Stock
New Item
$599.95
Free Shipping on orders $99 and up
One of the tricks for getting your E9X M3 to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber, there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.&Newline; &Newline; Designed in-house for the highest quality and versatility possible, we are confident our Hybrid Camber Plates are the perfect solution for your BMW M3! &Newline; &Newline; The first requirement we had envisioned for our plates is wide adjustability while the struts are still installed. This is to ensure that your suspension can be dialed in for either street or track without any issues. Our plates offer 3+ degrees of camber adjustment and 2.5+ degrees of caster adjustment.&Newline; &Newline; The next key feature of our camber plates is long term reliability. To achieve this, maintenance free, PTFE lined, stainless steel spherical monoballs were utilized along with replaceable 80A polyurethane bushings, giving these plates a long bearing life and reduced NVH. To further increase longevity, the bearing design features upper and lower seals to keep out moisture and contaminants.&Newline; &Newline; The final and most important design requirement was how these plates worked specifically with the E9X M3. To guarantee these plates were the best choice for your BMW, we designed these camber plates with as large of a surface area as possible to ensure even distribution of forces throughout the strut tower, preventing common mushrooming or cracking of the thin OE steel mounting location. We managed to accomplish this by staying close to the original suspension geometry, adding 13.5mm of height to the stock shock pin position and only 3.5mm overall to ride height. This ended up further benefitting vehicles with lowered suspension by improving shock travel distance and reducing the risk of bottoming out.&Newline; &Newline; These camber plates are fully compatible with OEM bump stops, factory style springs or race springs. and include hardware that accommodates both square seat and tapered seat shock pins.&Newline; &Newline; Features and Specifications:&Newline; Camber adjustment range: 3+ degrees &Newline; Caster adjustment range: 2.5+ degrees&Newline; Wide plate offering superior load distribution &Newline; Bolt rings: powder coated steel with 10.9 zinc plated knurled studs &Newline; Housing constructed from 6061-T6 alloy with type 2 black anodizing&Newline; 13.5mm higher shock pin position for longer travel&Newline; OEM bump stop compatible&Newline; Utilizes OEM spring perch pillow ball bearing 31331090612&Newline; Compatible with square and taper seat shock pins&Newline; Race & stock spring compatible&Newline; FK FKSSX12T Maintenance free, PTFE lined, stainless steel spherical bearing &Newline; Bearing isolated by replaceable 80A polyurethane bushings&Newline; Upper and lower sealed bearings
SPL Parts Titanium Series Adjustable Front Lower Street Control Arms - E8X E9X RWD
SPL Parts - Corporate Logo
T#:553781
Part#: SPLFLCAE9X
In Stock
$499.00
$499.00

These SPL Parts Front Lower Street Control arms replace OEM Part numbers 31122405860 and 31122405859

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These SPL front lower control arms open up a wide range of adjustment for roll center, camber, and track width adjustment and allow for full articulation with the correct ball joint angle. Instead of using traditional jam nuts, the main arm is slotted to allow the use of pinch bolts and SPL rotating clamps on their exclusive adjuster, making it easier to lock in track width and camber specifications.

*includes headlight adjusting rod

SPL Parts Billet Lower Control/Trailing Arms Feature:

  • Lightweight Aluminum and Titanium construction
  • Electroless nickel plated 4130 Chromoly Double Adjuster for quick adjustment
  • Correct ball joint angle for full articulation
  • Rotating Clamp design allows for easy access to lock down alignment settings
  • Low friction 3 piece Teflon lined FK sphericals and Heim joints/rod ends
  • Multiple size Stainless Steel roll center spacers for precise adjustment

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E82/88 BMW All Submodels

Turner Motorsport Race Adjustable Camber Plates - E82, E9X
Turner Motorsport - Corporate Logo
T#:340472
Part#: TSU9080RC9
In Stock
Starting at $399.89
Free Shipping
Starting at $399.89
Free Shipping

These are the Turner Camber Plates used on our Championship-winning E90 race cars (also fits E82 1-series). These plates adjust camber with a fixed caster setting and have a lot of important motorsport-developed features that other camber kits do not. These were a clean-sheet design when we raced the E90 328i in the Grand-Am/IMSA GS class.

By placing a specific focus on minimizing stack height while retaining strength, our "Max Lowered" camber plates offer maximum shock travel to allow dampers to perform properly at a wide range of ride heights.

Design Highlights -

  • preserves the correct E90 geometry
  • compatible with 60mm, 2.5", 2.25" springs
  • maximum shock travel
  • light weight
  • durable materials
  • large surface area
  • easy to use for fast camber changes

The Turner E90 Race Camber Plates are the most advanced design on the market. These are designed specifically for the E90 chassis - no shortcuts or cookie-cutter components. We started with a fresh design to make these very user friendly and easy to install and set up. The E90 front suspension has unique geometry and the strut is mounted at an angle that can put significant side loading on the strut shaft if it's not located properly. The location and angles for the main bearing were carefully engineered to allow the proper motion ratio and strut angles during adjustment. This greatly reduces bending forces on the strut itself which improves performance and longevity. By designing for one chassis we're able to focus on what works best in that application - proper fitment and operation without unnecessary adapters, easy-to-use camber and caster adjustments, and an intelligent modular design.

Another important feature of the Turner Camber Plates is the size of the upper plate. Our plates have a very large surface area to better spread strut forces through the strut tower. A smaller upper plate, like those found on competitor's kits, will localize strut forces and contribute to strut tower deformation ('strut tower mushrooming'). This is a very important feature especially as these cars get older and spend more time on the track. Deformed strut towers are a serious performance and safety concern and our camber plates are properly designed to handle the loads. The factory strut reinforcement plates are not required with our camber plates (but you can use them if you want to).

Since this design is specific to the E90, we can build it with the bare minimum of adapters and extra hardware. This not only cuts down on confusion but makes it easier to assemble and operate. We use the correct-sized bearing for the 16mm strut shaft; no sleeves or bearing adapters required. Only a small stainless steel spacer and the upper spring hats from your coil over kit are all that's required to install. We also produce the upper spring plates if you need them (see Additional Items below). We have used our camber plates with most of the major strut manufacturers on the market - AST, Koni Motorsport, Moton, Ohlins, MCS, Bilstein, and KW.

If you need upper spring hats for the top of the springs, see the Additional Items list below. We make upper spring hats for 60mm, 2.25" and 2.50" springs and in 14mm and 16mm strut pin sizes. If you don't see the spring hat that you need, click here for the full listing. Or call us directly.

This item fits the following BMWs (w/ Race Coil Overs):
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335i M3 - Sedan
2006-2012 E91 BMW 328i Wagon
2007-2012 E92 BMW 328i 335i 335is M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible


SPL Parts Titanium Series Adjustable Rear Upper Camber Arms - E9X E8X
SPL Parts - Corporate Logo
T#:553658
Part#: SPLRWBE9X
Direct Ship
$332.00
$332.00

These SPL Parts Rear Adjustable Camber Arms replace OEM part numbers 33326777980, 33322283545, 33322283546, and 33322406292

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

The stock rear wishbones/camber arms are prone to flexing under intense driving situations because they are curved. The SPL adjustable rear upper camber arms are a perfect fix for this, providing significantly stronger support and offer a wider range of camber adjustment for both stability and better handling.

Technical specifications:

  • Black Anodized and Gundrilled 2024 Aluminum Links
  • 6061 Aluminum Clamps
  • Titanium Socket Head Cap Screws
  • Tapered Stainless Steel Knuckle Mount Spacers
  • FK Rod Ends
  • Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E8X BMW All Submodels


SPL Parts Titanium Series Rear Upper Control Arms - E8X E9X RWD
SPL Parts - Corporate Logo
T#:553664
Part#: SPLRGLE9X
Direct Ship
$332.00
$332.00

These SPL Parts adjustable rear upper control arms replace OEM part numbers 33322283547, 33322283548, 33326782237, and 33326782238

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

The stock rear upper control arms in the E8X/E9X vehicles are made of welded sheet metal and aren't very strong, usually flexing under aggressive driving and heavy torque, leading to low stability and inconsistent handling. These control arms from SPL are much stronger and feature solid rod ends, offering outstanding stability and no suspension slop normally scene from OE rubber bushings.

Technical specifications:

  • Black Anodized and Gundrilled 2024 Aluminum Links
  • 6061 Aluminum Clamps
  • Titanium Socket Head Cap Screws
  • Tapered Stainless Steel Knuckle Mount Spacers
  • Teflon lined FK Rod Ends
  • Made in the USA!

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E8X BMW All Submodels

Dinan Fixed Camber Plates - E9X M3
Dinan - Corporate Logo
T#:393368
Part#: D160-0003
Direct Ship
$211.15
Free Shipping

The camber plates improve on the amount of adjustment and fine-tuning available in the front suspension to improve mechanical grip while cornering. Made to the same quality you'd expect from Dinan and BMW, they help to fine-tune the right amount of camber for Dinan springs.

  • Improved mechanical grip
  • Reduced understeer
  • Works great with Dinan springs
  • Worth 1 point toward your Dinan badge

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their aEURoetotal packageaEUR approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere.

This item fits the following BMWs:

2008-2013 BMW M3


SPL Parts Titanium Series Adjustable Front Lower Racing Control Arms - E8X E9X RWD
SPL Parts - Corporate Logo
T#:553873
Part#: SPLFLCARE9X
Direct Ship
$549.00
$549.00

These SPL Parts Front Lower Street Control arms replace OEM Part numbers 31122405860 and 31122405859

SPL Parts is a performance suspension manufacturer that designs and tests their products all in-house here in the USA. Additionally, all materials used are sourced from American suppliers to ensure consistently high quality products. SPL Parts products are all constructed using chromoly seamless straight tubing, DOM mandrel bent tubing, and 6061 and 2024 aluminum for high strength and quality. All TIG welding and CNC machining is also done locally by professional welders and machine shops to meet exact quality standards and tolerance specifications. For anything from racing to street driven needs, SPL Parts offer an amazing line of premium quality products that are perfect to get your car back in spec.

These SPL front lower control arms open up a wide range of adjustment for roll center, camber, and track width adjustment and allow for full articulation with the correct ball joint angle. Instead of using traditional jam nuts, the main arm is slotted to allow the use of pinch bolts and SPL rotating clamps on their exclusive adjuster, making it easier to lock in track width and camber specifications.

*DOES NOT include headlight adjusting rod

SPL Parts Billet Lower Control/Trailing Arms Feature:

  • Lightweight Aluminum and Titanium construction
  • Electroless nickel plated 4130 Chromoly Double Adjuster for quick adjustment
  • Correct ball joint angle for full articulation
  • Rotating Clamp design allows for easy access to lock down alignment settings
  • Low friction 3 piece Teflon lined FK sphericals and Heim joints/rod ends
  • Multiple size Stainless Steel roll center spacers for precise adjustment

Fits the following BMWs:
2006-2013 E9X BMW RWD Submodels
2008-2013 E82/88 BMW All Submodels

TC Kline Racing Camber Caster Plates - E36 E9X
TC Kline Racing - Corporate Logo
T#:401266
Part#: TCKE36CAMPLA
Direct Ship
$489.00
Free Shipping

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Made from aircraft grade aluminium, with stainless steels strut inserts and hardware for the ultimate in durability for street or track use. The built in reinforcement plate reduces the stress on the shock tower to reduce the chance of the shock towers tearing. With a maximum adjustment rang of -1.5 degrees camber per side, these plates will allow you to get your suspension right where you need it.

Will not fit with Bilstein Struts/Shocks. Will fit all other brands.

Fits the following BMW's
1992-1999 E36 BMW - 318ti 318i/is/ic 323i/is/ic 325i/is 328i/is/ic M3
2006-2013 E9X BMW - 325i/xi 328i/xi 330i/xi 335i/is/ix M3