BMW Engine Parts for BMW 3 Series E93 (2007-2013)

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

Failing ignition coils or plugs can cause sputtering, rough idle, hesitation on acceleration, misfires, and a check engine light. Replace it with this blue Dinan Performance ignition service kit!

The kit includes:

• 6 Dinan Coils with locks
• 6 Bosch spark plugs
• 1 packet of American Grease Stick dielectric grease

Dinan ignition coils features:

• Up to 10% more energy output than stock.
• Blue housing with Dinan Logo.
• True upgrade, not just aesthetic.
• Direct plug-and-play.

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. A dipstick is integrated into the cap so you can monitor the oil level. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The ECS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. Multiple brackets are available so you're not limited on where to mount it. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The ECS OCC also has a factory-like appearance.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles.

ECS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ 4 chamber design promotes excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Anodized black lightweight aluminum
+ Made in USA

This item fits the following BMWs with the N54 twin-turbo engine:
2008-2010 E82 BMW 135i
2007-2010 E9X BMW 335i 335xi
2006-2010 E60 BMW 535i 535xi

This is a complete plug and play solution to replace your stock Low-Pressure Fuel Pump (LPFP) with a new E85 certified bucketless assembly.

This solution provides up to 25% more flow than our standard Stage 2 LPFP upgrade and up to 150% more flow than the stock pump.  

This pump will support up to 550whp running 85% ethanol and 600whp running 50% ethanol. 

The Stage 2 bucketless kit includes the following:

• • A custom anodized billet fitting for the pump output and stock fuel line connection.
  • Our custom billet aluminum anodized bracket for the pump and float assembly
  • Two cotter pins to secure your float assembly
  • A new E85 compatible Walbro 450 pump
  • Spare vent tube clip
  • A new Walbro filter

If you still need more flow, the Stage 3 upgrade is also available and can be added to your Stage 2 bucketless pump.

The Stage 3 upgrade kit includes:

• • A complete plug and play solution by simply adding the secondary module
  • Our custom billet aluminum fitting to run both pumps in parallel
  • A new E85 compatible Walbro 450 pump
  • Wiring harness for the secondary pump
  • Spare vent tube clip
  • A new Walbro filter

• Recommended accessories:
  • Lock Ring Removal Tool
  • Hobb's switch 
     
• NOTE: These kits include a basic filter assembly.  When using this filter, running the vehicle under low fuel conditions can cause fuel starvation issues. If you do hard straight line accelerations when you have less than 1/8 tank of fuel, we would recommend running our standard Stage 2, 3, or Stage 4 pump.  In addition, if you intend to use this for road course applications, you may see starvation issues when running less than a half tank and doing long high G right turns.  Again for those applications we'd recommend one of our standard pump applications.

BMW N54 N55 Heat Exchanger - 17217536929 is designed to maintain optimal transmission oil temperatures, ensuring reliable performance and longevity for your BMW. This high-quality heat exchanger effectively manages heat, preventing overheating and potential damage to the transmission system.

• Optimal Temperature Control: Keeps transmission oil at a safe temperature, enhancing overall performance.
• Durable Construction: Built to withstand high temperatures and demanding driving conditions.
• Improved Reliability: Helps prevent transmission overheating, which can lead to costly repairs.
• Direct Replacement: Engineered to fit seamlessly with BMW N54 and N55 engines.

Turner Motorsport's BMW N54 N55 Heat Exchanger - 17217536929 is an essential component for maintaining the efficiency and durability of your transmission system.