BMW Engine Parts for BMW 3 Series E93 (2007-2013)

This is the OEM Bosch ignition coil that is the current replacement for most BMW 6 and 8-cylinder engines built since 2003. It's listed as a replacement coil for M54, M56, S54, N52, N54, N62, N63, N73, S63, S63TU and other engines. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed in our fitments tab. This part number replaces previous BMW part numbers 12130390064, 12130148594, 12131712219, and 12137551260.

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This Bosch part also satisfies BMW's service bulletin for 2001-2003 E46 M3 ignition coils (SIB 12 24 05). That SIB calls for Bremi or ERA brand coils but BMW has replaced them with this Bosch design.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Sold per coil. Includes connecting boot.

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.