BMW Engine Parts for BMW 3 Series E93 (2007-2013)

Vargas Stage 1 N55 turbo upgrade is good up to 425whp with proper tuning and high grade fuel. Vargas N55 turbo is an all-new turbo specially made for Vargas. They build it with a billet compressor wheel of their own design and a stock turbine. It will accept all of the stock water and oil lines and the original diverter valve (upgraded DV is recommended). This kit is a direct bolt-on replacement for the original turbo and necessary if you want to start making big power from the N55.

The stock plastic diverter valve and chargepipe is the weakest point for boost leaks (the plastic cracks). Vargas Turbo recommends upgrading it to a stronger DV design. The aluminum DV designs will hold up to just about any boost level currently available.

Vargas Turbo Technologies has been in business since 1979, offering rebuilt and re-engineered turbo solutions. For the BMW market, they identified a need for both cost-effective turbo replacements and proven turbo upgrades. It's recommended that the rest of the system be upgraded to handle your tuning goals. The final Vargas rebuilt turbos are better than the factory rebuilds and at a lower cost!

Oil Recommendation - modern engine oil is formulated for emissions and to be environmentally friendly. The additives in current oil lowers the oil's ability to withstand high temperatures and stresses, lowering its shear strength and its lubricating properties. Vargas recommends oils with high ZDDP (zinc and phosphorus) content that will better protect and cool the turbo bearings. Examples of high-zinc oils are Red Line Race, Red Line Euro, Motul 300V Racing, Joe Gibbs Racing, Valvoline VR-1 oil, and most Diesel-spec oils that you can buy off-the-shelf. Some oils, especially the Race type, will need more frequent oil changes and may be harmful to catalytic converters.

WHP rating: 425. This rating is used to compare various stage of Vargas turbo kits. There is no advertised horsepower gain with this kit as it depends on your other mods and tuning. The rating is provided as a reference to use in your tuning planning. Custom tuning is recommended to match thIS turbo to your existing mods and upgrades.

The CTA Fuel Injector Tool kit is designed to remove and install your fuel injectors. 130 180, 130 270, 130 320, 2249 115

Designed to service the following BMW platforms:

N20, N47, N54, N55, N57 and N63

This is a high quality replacement OEM VDO Mass Air Sensor.The MAF controls the amount of fuel that goes through the injectors based on the volume of air coming through the intake. If your vehicle is giving you a MAF code, replace it immediately to ensure you get the best gas mileage and performance. It is common for this part to fail slowly and cause poor fuel mileage and hampered performance. When it fails completely, the vehicle will stutter and stall as it falls into a limp mode. One way to check if your MAF is bad is to unplug the connector before starting your car. If it idles well (compared to a previous poor idle), your MAF needs replaced. If you let this maintenance part go, your fuel economy will suffer as too much fuel is going into the engine and not being burned. A great way to give your vehicle an efficiency boost.

OEM replacement for BMW part # 13627551638.

OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

BMW N54 3.0L MAHLE Forged Piston Kit 84.50mm delivers exceptional performance and reliability for BMW engines. This high-quality piston kit is designed to replace the weaker factory cast aluminum pistons with robust forged pistons, enhancing durability and heat tolerance for extreme engine conditions.

• Enhanced Strength: Forged from 2618 aluminum, these pistons are more resistant to extreme heat, detonation, and high pressure, providing superior performance.
• Precision Specifications:
  • Bore: 84.50mm
  • Stroke: 89.6mm
  • Rod: 145.05mm
  • CH: 31.7mm
  • Piston Style: Dish with 4 valve reliefs
  • Crown Volume: 17.2cc
  • Piston Mass: 314g
  • Pin Diameter: 22mm
  • Pin Style: Floating
• Complete Kit: Includes pistons, pins, clips, and rings (1.0mm, 1.2mm, 2.8mm thickness).
• Durable Coatings: Features phosphate, Grafal, and hard anodized top ring groove for added longevity.
• Sold as a Set: Comes as a set of 6 pistons.

MAHLE Motorsport's PowerPak and PowerPak+ piston kits are engineered for both high-performance and everyday driving, offering a reliable upgrade for BMW engines. With over 95 years of performance experience, MAHLE Motorsport provides advanced features and superior quality for your engine build.