Packaged by Turner for BMW 3 Series E93 (2007-2013)

This kit includes every thing needed to replace your rod bearings.

Kit includes

Upper and lower WPC-treated rod bearings Hardware Oil filter BMW TwinPower Turbo Oil Oil pan gasket RedLine assembly lube

These M3 rear guide rod arms are an upgrade for the non-M cars. The stock non-M arms are made from sheetmetal spot welded together at the ends. The arm tends to flex and bend under even moderate cornering loads. Factor in gripper tires and more torque and this arm is inadequate for stability and consistent handling. The M3 arms are one piece of aluminum offering greater strength and with a sealed monoball inner bushing that allows the arm to rotate (instead of twisting).

This package includes:

• Left M3 Guide Rod - 33322283547
• Right M3 Guide Rod - 33322283548

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. 

Kit Includes:

• Automatic transmission oil pan with integrated filter 
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 7 quarts Redline D4 automatic transmission fluid

Fits the following BMWs:
E84 BMW X1 xDrive35i
​E90 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission), 330i/xi, 335i/xi
​E91 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission)
​E92 BMW 328i/xi (with GA6HP19Z automatic transmission), 335i/x
​E93 BMW 328i (with GA6HP19Z automatic transmission),  335i
E60 BMW 525i/xi, 528i/xi, 530i/xi, 535i/xi
E61 BMW 525i, 530xi, 535xi
E70 BMW X5 xDrive30i
E71 BMW X6 35iX
E82/88 BMW 128i(with GA6HP19Z automatic transmission), 135i (N54)
F01/02 BMW 740i/Li
E85/86/89 BMW Z4 3.0i/Si sDrive30i M54 N52

When installing a new clutch, it is important to replace old hardware and common wear items. This ensures both a smooth and reliable installation. This also allows you to perform maintenance while everything is apart as opposed to a needing to make future repairs when everything is back together.

Included in this kit:

• Flywheel bolts
• Bolts bell housing, one time use!
• All hardware to re-mount the driveshaft
• Pilot Bearing
• Clutch fork pivot pin
• Clutch alignment tool
• Metal Guibo
• Center support bearing 

Fits the following BMWs:
E9X BMW 335i/is N54 N55

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

If you are looking to install a cup kit or a set of coilovers on your BMW, this kit will be a great aid in doing so. It includes everything you will need to do the job.

See kit contents tab for a list of included components.

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Suspension Bushings
Control Arm Bushings
Hardware
Rear Shock Mounts
Control Arms & Trailing Arms