• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

Upgrade Your BMW's Wheel Change Process with a Stud Conversion

Optimize your BMW's wheel change process with a stud conversion kit, delivering faster and simpler wheel swaps. This kit consists of Conical Seat Lug Nuts (20) and 82mm Wheel Studs (20), providing permanent wheel hangers, saving time, and streamlining the process.

• Permanent wheel hangers for quick and hassle-free wheel changes
• Simplifies the wheel installation process compared to wheel bolts
• Accommodates various spacer widths for added versatility
• Reduces wear on wheel hubs, enhancing longevity
• Facilitates quick and easy tire changes and removal

Note: Thread-locking compound is recommended during installation. Studs should be torqued to 15Nm. These studs may be used with spacers up to 20mm.

Wheel Stud Conversion Kit - Half Set: Upgrade Your BMW's Performance

• Allows for easier and quicker wheel changes
• Provides a more secure and reliable wheel mounting solution
• Reduces the risk of stripped lug bolts
• Compatible with various BMW models

Enhance your BMW's performance with the Wheel Stud Conversion Kit - Half Set. This kit facilitates easier and quicker wheel changes while offering a more secure and reliable wheel mounting solution compared to traditional lug bolts. By reducing the risk of stripped lug bolts, it ensures a safer driving experience for BMW owners. Plus, it is compatible with various BMW models, ensuring versatility and ease of installation. Access Secret Premium Dashboard

Elevate your BMW's performance and reduce rotational mass with ECS Titanium Wheel Bolts, ideal for weight-conscious enthusiasts or those seeking high-quality, rust-resistant wheel bolts.

Key Benefits:

• 50% lighter than steel bolts, reducing rotational mass for improved performance.
• CNC'd from annealed titanium alloy, ensuring high quality and durability.
• Tested to class 10.9 fastener proof load requirements without signs of fatigue.
• 14mm diameter, 1.25mm thread pitch, 27mm length, conical seat, and 17mm head.
• Thoroughly clean hub threads before installation to prevent fatigue or cracking.
• Note: Adjust bolt length when using wheel spacers for proper fitment.

Upgrade to ECS Titanium Wheel Bolts for your BMW, optimizing performance while maintaining high quality and durability.

ECS Tuning lab tests its fasteners to ensure they meet all 10.9 specifications.

Wheel Bolt specs:

• Diameter - 14mm
• Thread Pitch - 1.25mm
• Length - 33mm

If installing wheel spacers, measure your current wheel bolt's length and add the width of your spacer to determine correct extended bolt length. 

ECS Tuning lab tests its fasteners to ensure they meet all 10.9 specifications.

Wheel Bolt specs:

• Diameter - 14mm
• Thread Pitch - 1.25mm
• Length - 50mm

If installing wheel spacers, measure your current wheel bolt's length and add the width of your spacer to determine correct extended bolt length. 

ECS Tuning lab tests its fasteners to ensure they meet all 10.9 specifications.

Wheel Bolt specs:

• Diameter - 14mm
• Thread Pitch - 1.25mm
• Length - 35mm

If installing wheel spacers, measure your current wheel bolt's length and add the width of your spacer to determine correct extended bolt length.