BMW Tools & Specialty Equipment for BMW 6 Series F06 (2013+)

This tool comes in handy especially when working with an engine harness. Certain areas are always prone to corrosion and this tool makes having to re-pin a connector a breeze.

Unlike small screwdrivers, picks, and paper clips, these tools are the correct size and shape to remove and install tiny electrical pins and terminals at plastic block connectors with ease, and will not damage the connectors in the process.

Packaged in a blow molded case to keep everything secure and organized.

Protect your finish when working under the hood with a high quality Turner fender cover. Made from a synthetic leather layer with a goose flannelette backing for durability and protection. The Turner fender cover holds a tight grip to your fender or core support with four 9.5" magnets sewn into the top layer.

Features:

• Durable synthetic leather with the Turner logo
• Soft goose flannelette backing
• Four 9.5" integrated magnets

Dimensions:

•  Extra Long 20" x 47"

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage. By using a non-marring plastic you can safely and easily remove trip pieces with confidence

?

Features:

• Pull-type remover

• Narrow edge remover

• Wide edge remover

• Handle remover

• Upholstery clip remover

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible ½-inch drive click-to-stop
• Torque range of 10 to 150 ft-lb
• Accurate to within +/-4%
• 18 inches in length with a convenient carry case

Proper torque is very important when it comes to working on engines. The importance comes from proper sealing and to keep from damaging threads.

Features:

• Reversible 3/8"-inch drive click-to-stop
• Torque range of 5 to 80 ft-lb
• Accurate to within +/-4%

Safety is always the most important factor when it comes to working under your car, jack stands are highly recommended. 

Features:

• Ultra light  jack stands only weigh 4.7 lbs each
• All aluminum construction with heavy-duty  flanged bases to safely stabilize loads
• 6 locking positions for a secure load in multiple heights
• Extra heavy duty load pin at .584 in. diameter with a posi lock ball to insure it stays in place
• Min. Height is 10.6
• Max Height is 15.4"
• Large 7" diameter base
• Outer support tube is 2-1/8" in diameter

The Schwaben aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

If you're removing trim panels and don't want to scratch or break any pieces then this is a must have. Formed for precision and constructed from plastic to be gentle with the finish.

Features:

•  Wide type remover
• Pull type remover
•  Handy remover
• Narrow type remover
• Upholstery Clip remover
• Angled Clip Panel Remover
• Fork Tip Flat Clip Panel Remover
• Clip Panel Remover
• Sharp Tip Flat Clip Remover
• Panel Remover
• Blunt Tip Flat Clip Panel Remover

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

This large socket is the perfect tool for axle nuts when servicing the axle shafts or wheel bearings.

Features:

• ½-inch drive 46mm 12-point socket
• Specially hardened to take the added abuse from a impact gun
• Coated for added protection and so you can tell it apart from non impact rated sockets
• 75mm depth  to accommodate many applications and different length shafts
• Made of durable chrome moly steel

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
• Deluxe transverse support for even more stability
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly.