This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

Enhance wheel replacement efficiency on your BMW with a stud conversion kit, facilitating quicker and easier wheel changes. This comprehensive kit includes:

• Conical Seat Lug Nuts (20)
• 75mm Wheel Studs (20)

The installation of these studs provides a permanent wheel-hanging solution, saving time and reducing hassle during wheel changes. By simply screwing in the supplied studs, you'll be ready to go.

Benefits of using wheel studs instead of wheel bolts:

• Some racing regulations mandate wheel studs for enhanced wheel-to-hub contact, ensuring added safety.
• Wheel studs accommodate various spacer widths, eliminating the need for custom bolt lengths when using spacers.
• Simplifies wheel installation; the studs act as wheel hangers while nuts secure the wheel in place.
• Reduces wear on wheel hubs as wheel studs remain in the hub, unlike constantly removed and installed wheel bolts.
• Facilitates quick and easy tire changes as wheel studs stay in place.

Note: Use thread-locking compound during installation and torque studs to 15Nm for optimal performance.

Upgrade your BMW's wheel system with this stud conversion kit for improved convenience and functionality.

Upgrade your stock oil cooler thermostat for improved performance. Swap your factory 110-degree Celsius thermostat for a new 70-degree Celsius version for faster oil flow and extended temperature control. With oil temperatures reaching 230 degrees Fahrenheit by the time your factory thermostat opens, initiating oil flow at lower temperatures proves more effective than attempting to cool down already elevated temperatures.

Utilizing a factory-style thermostat, this upgrade can be used in all weather conditions and allows your engine to warm up properly, unlike thermostat bypass kits.

Kit contents:​

Lower temperature thermostat - 70c (158F) vs Factory 110c (230F)
Low temp thermostat spring

Your floor jack is universal but it doesn't have to be with this adapter! Most newer BMW jack pads have an open recess inside that this adapter fits into. It's a rectangular peg for a rectangular hole. This gives the jack a much more rigid connection and almost impossible for the jack or pad to slip. You will never have to worry about scratching your rocker panels or jacking from the wrong spot - the positive connection ensures you are always lifting from the correct location. This adapter is one of those small hidden gems that you can't live without! 

Made of black anodized aluminum for added strength and corrosion resistance, the adapter fits the head of most hydraulic floor jacks, including the Schwaben Low Boy.

Compatible with most BMW jack pads for chassis E39 and up. Retrofitting jack pads is common, especially on E36/Z3 models.

This braided stainless steel line replaces the stock hydraulic hose connecting your clutch slave cylinder to the clutch master cylinder. There are several deficiences with rubber, especially as it ages - when new the rubber expands and swells under pressure and the pedal can feel spongy. As rubber ages and is exposed to extreme temperatures the rubber can harden and even shrink (common on brake hoses), which results in a stiff pedal. Rubber clutch lines do not stand up to the stresses of hard use. ECS Exact-Fit stainless reinforced clutch lines provide more confident and dependable shifting by maintaining consistent line pressure, long lasting corrosion resistance, and increased protection from failure. These lines are reinforced with braided stainless steel mesh, affording superior expansion resistance. This resistance to expansion creates a firmer pedal, and a more direct clutch pedal feel. The signature red polymer coating provides additional protection from the elements and abrasion.

This particular stainless steel clutch line fits the following BMWs:
2004-2010 E60/E61 5 Series 
2004-2010 E63/E64 6 Series (manual transmission only, no SMG)
2011-20116 F07/F10 5 Series 
2011-2016 F06/F12/F13 6 Series

Engineered for vehicles with vacuum-actuated exhaust valves, the ECS Remote Vacuum Exhaust Valve Control Kit puts you in complete command of your exhaust sound. This fully standalone system lets you open or close your valves instantly—no reliance on factory controls, drive modes, or complicated wiring.

At its heart is a self-contained vacuum pump and dedicated control module, operating entirely independent of your vehicle’s electronics. The result is broad compatibility with both OEM and aftermarket exhaust systems, allowing for the freedom to switch between aggressive performance sounds and a refined, quiet tone at the touch of a button.

Kit Includes:

Standalone Vacuum Pump – Delivers consistent vacuum for reliable valve function

Wiring Harness Options – Choose from a reversible cigarette lighter power adapter or a length of wire for custom hardwiring

High-Quality Vacuum Hose – Durable, leak-resistant construction for long-lasting performance

Remote Controllers – Compact fobs for easy operation from inside or outside the vehicle

Features:

Instant open/close control for exhaust valves

Operates completely independent of factory electronics

Universal compatibility with vacuum-actuated valve systems

Ideal for both aftermarket and factory exhaust setups

From stealthy early-morning starts to unleashing your exhaust’s full roar on demand, the ECS Remote Vacuum Exhaust Valve Control Kit gives you total control over your car’s voice—whenever and wherever you want it.

Upgrade Your BMW's Wheel Change Process with a Stud Conversion

Optimize your BMW's wheel change process with a stud conversion kit, delivering faster and simpler wheel swaps. This kit consists of Conical Seat Lug Nuts (20) and 82mm Wheel Studs (20), providing permanent wheel hangers, saving time, and streamlining the process.

• Permanent wheel hangers for quick and hassle-free wheel changes
• Simplifies the wheel installation process compared to wheel bolts
• Accommodates various spacer widths for added versatility
• Reduces wear on wheel hubs, enhancing longevity
• Facilitates quick and easy tire changes and removal

Note: Thread-locking compound is recommended during installation. Studs should be torqued to 15Nm. These studs may be used with spacers up to 20mm.

The DCT transmission in your BMW is nothing short of incredible and exhilarating, but also astronomically expensive to replace. BMW has been labeling fluids as "lifetime" for quite some time now, and as enthusiasts and owners have learned over the years, there simply is no fluid that last a lifetime.

This DCT service kit that takes the guesswork out of a fluid change . No need to track down the correct fluid and plugs, simply open the box, and get the job done the correct way. By servicing your DCT transmission, you will be assured that old, broken down fluid won't cause a several thousand dollar nightmare. We recommend this service every 40,000 miles to keep your transmission going strong for years to come.

Kit includes:

• 5 quarts of Pentosin DCTF-1 fluid
• DCT transmission cartridge and suction filters
• Drain and fill plugs

Please note: We include 5 quarts of DCT fluid because without a GT1 diagnostic tool and much more involved labor, you will not be able to replace over 5 quarts of fluid. Many elect to do this service and simply flush the fluid 5,000 miles later to ensure all fluid has been flushed, but this is not mandatory.

Both the cartridge and suction filters have their own challenges in replacing. For best results, replace both.

Upgraded replacement for your crankcase vent hose P#11127584128 featuring upgraded silicone, stainless steel clamps, and new OE connectors and seals.

Enhance your BMW N55 engine with our Silicone Crank Case Vent Hose, a premium replacement for the fragile, failure-prone factory hose. Over time, the stock plastic hose deteriorates due to constant exposure to heat and oil, leading to cracks and leaks. Our solution? A high-quality silicone hose engineered for superior durability and long-term reliability.

To further enhance performance, we’ve lined the hose with fluorosilicone, providing exceptional resistance to oil and chemical degradation. Designed in-house using advanced CAD modeling and 3D scanning, this hose offers a precise OEM fit while eliminating the common weaknesses of plastic construction.

Each kit includes stainless steel hose clamps for a secure, hassle-free installation. Whether you’re replacing a worn-out CCV hose or upgrading for added peace of mind, this premium solution ensures your BMW N55 runs smoothly and efficiently for years to come.

Features:

Arrives preassembled with new OE fittings and seals
Direct OEM Fit – Retains factory hose dimensions while eliminating reliability issues.
High-Performance Silicone – Resists heat-related wear for long-lasting durability.
4-Ply Fluorosilicone Lining – Superior protection against oil and chemical exposure.
Stainless Steel Clamps Included – Secure installation and extended service life.
Give your BMW N55 the reliability it deserves—upgrade to the ECS Tuning Silicone CCV Hose today!

Unsure of what size spacer will work best for you? This professional kit includes 1mm, 2.5mm, 5mm, 10mm, and 15mm spacers with wheel studs and nuts for you play with. These are not the same spacers that we sell and they cannot be used to drive on. But with the studs installed the car can be lowered to the ground and rolled to check for clearances. These test fit spacers are drilled to fit the standard BMW 5x120 bolt pattern as well as 4-lug 4x100 (and VW/Audi bolt patterns too). You can stack spacers to achieve the perfect clearance. When you're ready call us to order the spacers you need (we make 3mm, 5mm, 7.5mm, 10mm, 12.5mm, 15mm, 17.5mm, 20mm, 25mm, and 30mm spacer thicknesses).

This kit is for purchase only. It's perfect for shops or racecars where changing wheels or brakes is common. We also have kits that are available for rent.

These spacers are not for driving on. They lack the hubcentric lip that BMW wheels are designed to work with. Driving on studs alone will lead to a failure.

Drastically improve the looks of your vehicle while improving your vehicle's handling characteristics and/or easily adjust your wheel fitment to allow for the proper clearance when installing parts such as new wheels, big brake kits, or lowering suspension components.Interference from components such as shocks, springs, or control arms are a common issue when installing wheel that are not a direct OE size replacement. By moving your wheels a few millimeters each, you can give yourself enough clearance for proper wheel fitment and give your car a wider stance in the process.

ECS Tuning wheel spacers are constructed of high quality 6061-T6 aircraft grade aluminum and are specifically designed by in-house engineers and cnc machined to exact standards, ensuring the best fitment possible. By carefully measuring the OEM wheel hubs and bore dimensions, these spacers mount with minimal clearance to prevent any vibration, retaining the stock-like vibration free operation. 

ECS Tuning is a performance and genuine parts provider that designs their ECS Tuning branded aftermarket automotive parts in-house to ensure the highest quality and affordability possible. Every part's design is subjected to a rigorous test fit and stress test period to guarantee proper fitment and continued reliability for years to come.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135 1M
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2012 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2012 E93 BMW 328i 335i M3 - Convertible
1976-1981 E12 BMW 528i 530i
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi M6
2004-2010 E63 BMW 645ci 650i M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2016 Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is
Rear Only
2007-2013 E70 BMW X5M
2007-2014 E71 BMW X6 xDrive35i X6 xDrive50i X6M