At Turner we are very familiar with the N55 and B58. These are the new generation engines that you you can pull quite a bit of power from quite easily, if you want to put the power to the pavement the factory bushings and reinforcement just wont cut it. With soo many performance parts available for the turbocharged engines, it is very easy to make power but keeping the car under control can be another story. Reduce wheel hop, extend the life of your bearings, and add stability to your chassis!

Our in-house engineers created a solution to help transfer the power to the ground, the result is a simple yet astounding improvement to the performance of your vehicle. The rear diff brace helps put power down by reducing wheel hop and preventing losses during power transfer. With the added rigidity the rear end feels tighter for high speed applications and will extend the life of your choice of OE or aftermarket bushings.

Soft factory rubber differential bushings absorb vibrations between the chassis and differential, providing comfort and softness for normal driving conditions. As these bushings wear you will experience lackluster performance/response and they will need to be replaced. You can extend the life of these bushings while providing increased chassis stability with our differential brace for your F chassis. Add new poly differential bushings for an even better experience (T#:656153)

Note: Drilling is required for installation

Benefits:

Reduce unwanted drivetrain deflection, offering a more enhanced driving experience
Reduced wheel hop
Extend the life of your bushings
Reduced wear on the differential bearing
Increased transfer of power to the pavement
Increased high speed stability
Engineered by Turner to withstand extreme driveline forces of over 1000 Ft/lbs of torque
Provides necessary installation tooling to properly secure brace
PART DESIGN:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Constructed using aircraft grade 6061-T6 Aluminum, finished in Turner Blue anodization
FEA simulations run to maximize stiffness to weight at base engine power and torque levels with plenty of room for growth
Corrosion resistant Yellow Zinc-Chromate coated grade 10.9 Fasteners
KIT CONTENTS

Turner Blue Anodized Rear Diff Brace
Drill guides for precision installation
Hardware for installation
INSTALLATION:

- Click HERE for Installation Instructions -
Requires 10mm + 15mm carbide tip steel drill bits (T#16907167)
PRODUCT DEVELOPMENT

Turner F Chassis Differential brace was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.

Increase drivetrain rigidity and put that power to the ground! This industry-leading encapsulated design reduces NVH and prevents heat transfer.

From the factory, all BMW models are equipped with soft rubber or fluid-filled engine mounts. While these mounts perform well at isolating drivetrain vibrations, they are prone to degradation and allow for significant drivetrain movement. This often results in a loose-feeling driveline, missed shifts, and a generally disconnected driving feel.

To address these issues, We have developed a performance alternative. Constructed from 6061 Billet Aluminum, these mounts are built to last. While most performance drivetrain mounts feature solid or polyurethane-bonded aluminum construction, the engineers at Turner designed a unique four-piece design that disburses NVH (noise, vibration, and harshness). This multi-piece design offers the added benefit of serviceability. Additionally, encapsulating the polyurethane and adding a TecaPeek isolator prevents heat transfer to the insert, increasing the lifespan and durability of the mount.

Features & Benefits:

High-strength 6061 billet aluminum construction
80A Polyurethane provides a considerable increase over stock rubber durometer, eliminating excess deflection and ensuring drivetrain stiffness.
Instead of the typical polyurethane-bonded aluminum construction, this mount is encapsulated to reduce NVH (noise, vibration, and harshness).
Finished in black hard-coat anodized for a clean, durable, and corrosion-resistant finish.
TecaPeek isolator reduces heat transfer from the engine to the mount insert, increasing the lifespan of the mount.
A simple bolt-on design makes for an easy install
Replace your worn-out factory engine mounts and experience increased drivetrain rigidity, reduced deflection, and more precise shifting. Our Turner Performance Polyurethane Engine Mount Set is designed for maximum durability and strength while maintaining the perfect balance between stiffness and comfort—the perfect choice for your high-horsepower BMW!

Modern BMW's are beginning to leave the performance derived handling and power delivery in the past as the demand for more comfort and features rises. The stiff suspension components designed around having the best driving experience from a luxury car has been left for the M models and replaced with soft rubber bushings and mounts. Unfortunately, this is a good move by BMW to support the masses.

The obvious approach was to offer products so the modern BMW can be upgraded into the car the enthusiast desires, superb handling, control, and a direct delivery of power to the rear wheels. When you upgrade to our Delrin subframe mounts you reconnect that power with almost zero negative feedback.

The added appeal to someone looking to take one of these machines on the race track is Delrin can be used when solid mounts are needed and aluminum is not an option with strict regulations found in??Grand-Am, BMW CCA, and other racing series.

Product features:

• Precision machined Delrin(TM) 150 bushings.
• Precision machined 6061-T6 aluminum inserts.?
• Class legal for any racing class that does not allow a solid subframe bushing.?

Performance Benefits:

• Eliminates subframe movement for more direct throttle and suspension? response.?
• Minimizes wheel hop due to subframe deflection and movement.?

?

***Installation Instructions***

These GAC differential bushings/mounts fit the following BMWs:?
2014+?F22 BMW?228i 228iX M235i M235iX?
2012+?F30 BMW?320i 320iX 328i 328iX 335i 335iX - Sedan?
2014+?F34 BMW?328i 328iX 335iX - Gran Turismo?
2014+?F32 BMW?428i 428iX 435i 435iX - Coupe?
2014+?F33 BMW?428i 428iX 435i 435iX - Convertible

2014+?F36?BMW?428iX -Gran Coupe?

Enhance your car's performance with ECS Tuning's polyurethane transmission mounts, designed for both street and track applications. These mounts are engineered to withstand high torque and forced-induction scenarios, eliminating concerns about torn mounts and providing a more engaging driving experience. Although polyurethane may introduce some additional NVH (Noise, Vibration, Harshness), its exceptional durability, wear resistance, and resistance to water, oil, and grease make it the perfect choice for performance enthusiasts. ECS Tuning offers two durometer options to match your driving style, along with a comprehensive DIY installation guide, ensuring a complete solution for your transmission mount requirements.

Key Features:

• Minimized transmission movement, reducing the risk of mis-shifts and over-revs.
• Made from high-quality polyurethane bonded with 304 Stainless Steel.
• Enhanced driving experience for both street and track enthusiasts.
• Two durometer options available: 80A for race applications and 70A for daily driving (ES#2859359).
• Replaces weak OEM mounts.

The stock center support bearing carrier is engineered to minimize noise, vibration, and harshness (NVH) in the cabin by loosely securing the center bearing with a soft rubber bushing. However, this design allows the driveshaft to move off-center during launches and shifts, reducing throttle response and causing drivetrain oscillations. Over time, the rubber bushing can sag or dry rot, leading to misalignment of the driveshaft.

Prevent or fix this common problem with JXB Performance's Driveshaft Center Support Bearing Upgrade! This upgrade features a simple yet highly effective 2-piece design that makes installation and bushing replacement effortless. The stock carrier is cut away, and the JXB bushings securely "clamp" the driveshaft bearing in place, ensuring constant driveshaft alignment.

The Street bushing option from JXB is the most popular choice, offering a significant improvement over the stock design while keeping NVH levels minimal.

Note: Some light NVH, such as a soft hum, may occur at certain speeds. However, with a modified exhaust or open windows, it’s unlikely to be noticeable.

Installation is straightforward and doesn’t require removing the driveshaft. The 2-piece design clamps directly onto the OEM bearing, though removing the old carrier will require a cutting tool.

Need replacement or additional bushings? See T#4799658 for replacement street bushings.

The ECS Tuning Center Support Bearing Brace is engineered to improve drivetrain performance and longevity. The factory center support bearing features internal an internal rubber bushing to reduce NVH (noise, vibration, and harshness) transmission to the cabin. Unfortunately, this material choice falls short when it comes to performance applications. Under extreme load conditions, this bushing is prone to flexing, resulting in driveshaft misalignment. To address the shortcomings of the factory rubber center support carrier design, ECS engineers developed a set of precision-fit, split polyurethane bushings that secure tightly around the existing driveshaft bearing. Constructed from 90A durometer polyurethane, this material eliminates bushing deflection while maintaining minimal noise, vibration, and harshness (NVH). By eliminating deflection, this innovative solution not only improves durability but also ensures a significantly longer service life than the OEM center support bearing—making it an excellent upgrade for aging BMW chassis.

The polyurethane bushings are surrounded by a robust 6061-T6 billet aluminum bracket designed with strength and reliability in-mind. This bracket features a split design for hassle-free installation, eliminating the need to remove the driveshaft assembly entirely. To install the ECS Center Support Carrier, simply cut around your existing bearing, remove the factory brace, and clamp on your new bushings and bracket. This user-friendly approach saves time and simplifies maintenance or upgrades. Two stainless steel socket head screws are used to fasten the two-piece bracket, offering corrosion resistance and secure clamping under high torque and stress. This combination of materials and design ensures dependable performance and long-lasting durability, even in demanding applications.

Features & Benefits:

Performance-Designed Bushing Upgrade: 90A durometer polyurethane is used to eliminate bushing deflection while maintaining a smooth, quiet ride. Improved Longevity: Polyurethane construction offers a longer lifespan than factory rubber, ideal for enthusiasts looking to eliminate future CSB-related problems. Billet Aluminum Bracket: The upgraded bushings are encased in a 6061-T6 billet aluminum bracket for enhanced durability and improved performance. Easy Installation: Both the bushings and the bracket feature a two-piece split design, allowing for seamless installation without driveshaft removal. Reduce Deflection, Increase Rigidity: Designed with performance in mind, this upgrade eliminates excessive driveshaft movement for improved alignment and efficiency. Kit Includes:

ECS Driveshaft Center Support Bushings ECS Driveshaft Center Support Carrier (2) Stainless Steel Hex Head Screws (2) Hex Bolts (22326760945) Medium Strength Threadlocker (0.5ml)

EXTRACTOR:

The Schwaben 6.5 Liter Extractor empowers you with swift, hand-operated fluid extraction. Complete with two tubes of varying diameters to suit your unique needs, this system's vacuum release button guarantees seamless operation. Clearing 6.5 Liters (6.8 qts.) of fluid in minutes, it preserves a spotless, oil-free workspace. Its ingeniously designed pour spout ensures mess-free fluid disposal.

Features:

• Stability First: Equipped with a flip-out foot for steady usage, delivering precise extraction.
• Organized Efficiency: Integrated hose storage streamlines your extraction process.
• Perfectly Sized: A 41" main tube (3/8" OD) and two 35" extension tubes (1/4" and 3/16" OD) ensure versatility across applications.
• Beyond Extraction: It doubles as a brake bleeder with the optional ES3248036 Brake Bleeder Hose.
• LIFETIME REPLACEMENT: Like almost all Schwaben tools, this fluid extractor is backed by our lifetime replacement program should anything go wrong!

ADAPTER:

This adapter hose allows a quick and easy suction thru the bleeder screw. This hose has included shut off valve in hose.  This will improve your extractor capabilities and make it even more of an all-in-one tool!

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

This is an OEM LuK stock dual mass flywheel. When your clutch starts to experience engagement chatter because of hot spots and wear, replacing it with this OEM dual mass flywheel will restore your vehicles driveability and have you clutch shifting smoothly again. OEM replacement for BMW part # 21207640733 and 21207598460.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!