BMW Drivetrain Parts for BMW 4 Series F32 (2014+)

At Turner we are very familiar with the N55 and B58. These are the new generation engines that you you can pull quite a bit of power from quite easily, if you want to put the power to the pavement the factory bushings and reinforcement just wont cut it. With soo many performance parts available for the turbocharged engines, it is very easy to make power but keeping the car under control can be another story. Reduce wheel hop, extend the life of your bearings, and add stability to your chassis!

Our in-house engineers created a solution to help transfer the power to the ground, the result is a simple yet astounding improvement to the performance of your vehicle. The rear diff brace helps put power down by reducing wheel hop and preventing losses during power transfer. With the added rigidity the rear end feels tighter for high speed applications and will extend the life of your choice of OE or aftermarket bushings.

Soft factory rubber differential bushings absorb vibrations between the chassis and differential, providing comfort and softness for normal driving conditions. As these bushings wear you will experience lackluster performance/response and they will need to be replaced. You can extend the life of these bushings while providing increased chassis stability with our differential brace for your F chassis. Add new poly differential bushings for an even better experience (T#:656153)

Note: Drilling is required for installation

Benefits:

Reduce unwanted drivetrain deflection, offering a more enhanced driving experience
Reduced wheel hop
Extend the life of your bushings
Reduced wear on the differential bearing
Increased transfer of power to the pavement
Increased high speed stability
Engineered by Turner to withstand extreme driveline forces of over 1000 Ft/lbs of torque
Provides necessary installation tooling to properly secure brace
PART DESIGN:

Designed and engineered in-house using state of the art 3D laser scanning and CAD technology for precision fitment
Constructed using aircraft grade 6061-T6 Aluminum, finished in Turner Blue anodization
FEA simulations run to maximize stiffness to weight at base engine power and torque levels with plenty of room for growth
Corrosion resistant Yellow Zinc-Chromate coated grade 10.9 Fasteners
KIT CONTENTS

Turner Blue Anodized Rear Diff Brace
Drill guides for precision installation
Hardware for installation
INSTALLATION:

- Click HERE for Installation Instructions -
Requires 10mm + 15mm carbide tip steel drill bits (T#16907167)
PRODUCT DEVELOPMENT

Turner F Chassis Differential brace was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing.

The ZF 8-speed automatic transmission (8HP) has become the go-to choice for performance enthusiasts, delivering lightning-fast shifts, impressive torque handling, and ample tuning potential. However, the stock transmission pan falls short in critical areas. Its plastic construction, integrated non-replaceable filter, and limited fluid volume leave little margin for error in demanding conditions.

To address these limitations, we've engineered a premium solution: a cast aluminum transmission pan that boosts durability, cooling performance, and serviceability. Designed with enthusiasts in mind, this upgraded pan increases fluid capacity by 1 liter to reduce transmission temperatures and improve long-term reliability, even under aggressive driving or track conditions.

Built to outlast and outperform the OEM plastic pan, the aluminum construction resists damage from road debris and eliminates the risk of cracking. Our pan is hard-coat anodized in black for superior corrosion protection and a long-lasting finish that looks as good as it performs.

Our aluminum pan upgrade is engineered to work seamlessly with the OEM G8X 8HP transmission filter (24007855263), allowing for easy and cost-effective fluid service. Integrated magnets help to trap metal particulate, extending the life of your transmission by keeping contaminants out of the fluid.

Key Features:

Cast aluminum construction offers superior strength and resilience over the OE plastic pan

Increased fluid capacity (+1L) enhances thermal management and reduces the risk of overheating

Serviceable design uses the OEM G8X transmission filter for easy, affordable maintenance

Hard coat anodized finish provides exceptional corrosion resistance and longevity

Integrated magnets collect metallic debris, protecting transmission internals

Kit Includes:

Turner Motorsport ZF 8HP High-Capacity Aluminum Transmission Pan
OE Hengst G8X Filter Installation Kit
Installation:

Vehicle plastic belly pans may vary. Because the Turner 8HP transmission pan is taller to allow for increased fluid capacity, some vehicles may require trimming of the plastic belly pan, or the belly pan may need to be installed over the transmission pan where it may make contact.

Modern BMW's are beginning to leave the performance derived handling and power delivery in the past as the demand for more comfort and features rises. The stiff suspension components designed around having the best driving experience from a luxury car has been left for the M models and replaced with soft rubber bushings and mounts. Unfortunately, this is a good move by BMW to support the masses.

The obvious approach was to offer products so the modern BMW can be upgraded into the car the enthusiast desires, superb handling, control, and a direct delivery of power to the rear wheels. When you upgrade to our Delrin subframe mounts you reconnect that power with almost zero negative feedback.

The added appeal to someone looking to take one of these machines on the race track is Delrin can be used when solid mounts are needed and aluminum is not an option with strict regulations found in??Grand-Am, BMW CCA, and other racing series.

Product features:

• Precision machined Delrin(TM) 150 bushings.
• Precision machined 6061-T6 aluminum inserts.?
• Class legal for any racing class that does not allow a solid subframe bushing.?

Performance Benefits:

• Eliminates subframe movement for more direct throttle and suspension? response.?
• Minimizes wheel hop due to subframe deflection and movement.?

?

***Installation Instructions***

These GAC differential bushings/mounts fit the following BMWs:?
2014+?F22 BMW?228i 228iX M235i M235iX?
2012+?F30 BMW?320i 320iX 328i 328iX 335i 335iX - Sedan?
2014+?F34 BMW?328i 328iX 335iX - Gran Turismo?
2014+?F32 BMW?428i 428iX 435i 435iX - Coupe?
2014+?F33 BMW?428i 428iX 435i 435iX - Convertible

2014+?F36?BMW?428iX -Gran Coupe?

The ECS Tuning Center Support Bearing Brace is engineered to improve drivetrain performance and longevity. The factory center support bearing features internal an internal rubber bushing to reduce NVH (noise, vibration, and harshness) transmission to the cabin. Unfortunately, this material choice falls short when it comes to performance applications. Under extreme load conditions, this bushing is prone to flexing, resulting in driveshaft misalignment. To address the shortcomings of the factory rubber center support carrier design, ECS engineers developed a set of precision-fit, split polyurethane bushings that secure tightly around the existing driveshaft bearing. Constructed from 90A durometer polyurethane, this material eliminates bushing deflection while maintaining minimal noise, vibration, and harshness (NVH). By eliminating deflection, this innovative solution not only improves durability but also ensures a significantly longer service life than the OEM center support bearing—making it an excellent upgrade for aging BMW chassis.

The polyurethane bushings are surrounded by a robust 6061-T6 billet aluminum bracket designed with strength and reliability in-mind. This bracket features a split design for hassle-free installation, eliminating the need to remove the driveshaft assembly entirely. To install the ECS Center Support Carrier, simply cut around your existing bearing, remove the factory brace, and clamp on your new bushings and bracket. This user-friendly approach saves time and simplifies maintenance or upgrades. Two stainless steel socket head screws are used to fasten the two-piece bracket, offering corrosion resistance and secure clamping under high torque and stress. This combination of materials and design ensures dependable performance and long-lasting durability, even in demanding applications.

Features & Benefits:

Performance-Designed Bushing Upgrade: 90A durometer polyurethane is used to eliminate bushing deflection while maintaining a smooth, quiet ride. Improved Longevity: Polyurethane construction offers a longer lifespan than factory rubber, ideal for enthusiasts looking to eliminate future CSB-related problems. Billet Aluminum Bracket: The upgraded bushings are encased in a 6061-T6 billet aluminum bracket for enhanced durability and improved performance. Easy Installation: Both the bushings and the bracket feature a two-piece split design, allowing for seamless installation without driveshaft removal. Reduce Deflection, Increase Rigidity: Designed with performance in mind, this upgrade eliminates excessive driveshaft movement for improved alignment and efficiency. Kit Includes:

ECS Driveshaft Center Support Bushings ECS Driveshaft Center Support Carrier (2) Stainless Steel Hex Head Screws (2) Hex Bolts (22326760945) Medium Strength Threadlocker (0.5ml)

Turner Motorsport Lightweight N55 Flywheel & Upgraded Clutch Kit

Unlock the full potential of your N55-powered BMW with our performance-driven clutch and flywheel kit. Designed to enhance daily drivability while delivering increased power handling and improved throttle response, this kit is the ultimate upgrade for enthusiasts seeking more from their vehicle.

Why Choose This Kit?
This setup features the Turner Lightweight N55 Flywheel, precision-engineered for quicker acceleration, faster rev-matching, and a more responsive driving experience. Paired with an upgraded OE clutch from the high-performance 335is and F10 550i(V8 Bi-Turbo), this combo is capable of handling over 500 ft-lbs of torque while maintaining smooth, factory-like engagement and durability.

The factory dual-mass flywheel may prioritize smoothness and efficiency, but it comes at the cost of responsiveness and is prone to failure in high-performance applications. The Turner Lightweight Flywheel solves these issues with a single-mass design that strikes the perfect balance between comfort, performance, and reliability making it ideal for both daily driving and spirited track use.

Kit Contents:

Turner Lightweight N55 Single-Mass Flywheel (18.6 lbs, 10 lbs lighter than stock)
Upgraded OE Clutch – Supports 500 ft-lbs+
OE Clutch Fork - P# 21517564027
OE Throwout Bearing
Brass Clutch Fork Pivot Pin - P# 21511223328
OE Flywheel Bolts - P# 11227520706
OE Pressure Plate Screws - P# 21207548052
Pivot Pin Retaining Spring - P# 21517570284
Transmission Mating Dowels - P# 11117524470
Flywheel Features:

Precision-machined 4140 HT heat-treated chromoly steel for durability
Black oxide coating to resist corrosion
Precision balanced to exceed OEM standards
Optimized step height for longer clutch life and consistent performance
Clutch:

Upgrade for 135i/335i/535i models from the 335is! Featuring a heavy-duty clutch with more holding power and a stock-like pedal feel. Excellent solution for If your clutch is slipping, or the engagement isn't what it used to be, it's time for a replacement. Slipping clutches won't allow your BMW to accelerate properly and can pose problems under a load such as going up large inclines. Also, a worn clutch can cause less precise and engaging shifts. By replacing your clutch you will restore performance and driving pleasure.

This clutch is an excellent upgrade for non 335is/550i/650i models. It features a more heavy-duty clutch disc and more holding power with stock-like pedal effort.

Transform your driving experience with this Turner Motorsport clutch and flywheel kit - engineered for power, performance, and everyday reliability.

It only takes a gust of wind to have your hood crashing down on your head, or if you have a carbon fiber hood and no longer have the gas struts than this could be what you need.

 This hood prop is adjustable, lightweight, and sturdy making it easy to keep out of the way in the trunk so it's there whenever you need it.