Select Vehicle
BMW
Mini
Category
- Drivetrain
Create an account to be able to build Wish Lists.
Please ensure your correct model is selected
Ensure optimal performance for your BMW with the Genuine BMW LT-5 Manual Transmission Fluid. Specifically formulated to meet BMW specifications, this 1-liter container of SAE 75W80 fluid is designed for manual transmissions. Keep your BMW's transmission running smoothly and efficiently with this authentic BMW fluid.
Upgrade your BMW's manual transmission with the Genuine BMW LT-5 Manual Transmission Fluid, providing the quality and performance your BMW deserves.
Genuine BMW hex bolt. M12X1,5X28
Be sure to replace your hardware with any flywheel removal service such as the rear main seal or clutch and flywheel.
This Genuine BMW OE replacement clutch kit from BMW comes stock for the 335is, 550i, and 650i. A lot of our customers install this as an upgrade for the 135i 335i and 535i!
Includes:
Genuine BMW Clutch Kit for your 6 Speed Manual Transmission vehicle -
This item fits the following BMW Chassis:
E92,E93,F10,F12,F13
A common source of leaks, the selector shaft seal should be replaced whenever the shifter assembly is serviced to prevent fluid loss.
Fits the following BMW chassis:
E36, E39, E46, E36/7 Z3
Genuine BMW Hypoid Axle Oil G1 - 0,5L
Ensure proper maintenance for your BMW's differential with the Genuine BMW Axle Oil Change Kit. This kit contains essential components, including a Genuine BMW fill bolt and two 500 ML Hypoid axle oils (G1). Note that no drain bolt is equipped on the vehicle. For fluid drainage, a transfer pump is required. Visit ECS Tuning's drivetrain section under maintenance for a comprehensive selection of tools, including transfer pumps, to facilitate the oil change process for your BMW's differential.
Key Benefits:
This is the stock twin mass flywheel for the N55 engine used in the E82 135i, E9X 335, F3x 335/435, and F10 535i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.
The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.
DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.
A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.
This item fits the following BMWs with the single turbo N55 engine and manual transmission:
2011-2012 E82 BMW 135i
2011 E90 BMW 335i 335xi 335i xDrive - Sedan
2011-2013 E92 BMW 335i 335xi 335i xDrive - Coupe
2011-2013 E93 BMW 335i - Convertible
2012-2015 F30 BMW 335i 335iX - Sedan
2014-2016 F34 BMW 335iX - Gran Turismo
2014-2016 F32 BMW 435i 435iX - Coupe
2014-2016 F33 BMW 435i 435iX - Convertible
2014-2016 F36 BMW 435i 435iX - Gran Coupe
2011+ F10 BMW 535i 535i xDrive