BMW Drivetrain Parts for BMW 4 Series F32 (2014+)

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and upgraded bushings that will give you a tighter shifting feel than traditional rubber bushings and will resist wear significantly longer.

This kit is perfect to restore your driving pleasure and will be the last shifter rebuild you will ever need!

See the included components under Kit Contents below.

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles.

Kit Includes:

• Automatic transmission filter with associated hardware
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 7 quarts automatic transmission fluid

Fits the following BMW chassis with 8 speed transmissions:
E70, E71, F01, F02, F06, F07, F10, F12, F13, F13, F15, F16, F22, F23, F25, F26, F30, F31, F32, F33, F34, F36, G11

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and upgraded bushings that will give you a tighter shifting feel than traditional rubber bushings and will resist wear significantly longer.

This kit is perfect to restore your driving pleasure and will be the last shifter rebuild you will ever need!

See the included components under Kit Contents below.

Tired of dealing with excess shifter slop and a mushy shifter? The Turner Shifter Rebuild & Upgrade Kits will restore your shifter's crisp feel and eliminate excessive movement that develops over time with wear. Included in this kit are all the common wear components and OE quality bushings that will give you a tighter shifting feel and will hold up like a day 1 BMW.

This kit is perfect to restore your driving pleasure!

See the included components under Kit Contents below.

This is the stock twin mass flywheel for the N55 engine used in the E82 135i, E9X 335, F3x 335/435, and F10 535i. It's manufactured by OEM supplier LuK. Sachs recommends a new dual mass flywheel (DMF) on every other clutch replacement. There are several indicators for replacing the flywheel: damage to the clutch contact plate (from a severely worn clutch disc), grease leaking from inside (overheating), build-up of clutch material on the contact plate (excessive slipping and overheating), and failure of the internal damping system.

The dampening system uses rubber or coil springs to absorb driveline vibrations. Through age, excessive heat, and aggressive use the rubber loses its resilience and the metal springs lose their strength and become brittle. If the clutch and flywheel have become overheated the internal grease may break down as well. A DMF failure can be massive and catastrophic, not to mention dangerous as bits of metal and rubber fling themselves through the transmission bellhousing. Heat and aggressive driving will accelerate the wear so race and track cars should have their stock flywheels replaced at regular intervals or with any new clutch. Even normal street cars should plan for a new flywheel if it has high mileage.

DMF wear can only be checked with the transmission and clutch removed. If you can rotate the outer flywheel more than 20mm in either direction then it should be replaced.

A new pilot bearing (roller bearing) is included, pre-installed in the flywheel hub.

This item fits the following BMWs with the single turbo N55 engine and manual transmission:
2011-2012 E82 BMW 135i
2011 E90 BMW 335i 335xi 335i xDrive - Sedan
2011-2013 E92 BMW 335i 335xi 335i xDrive - Coupe
2011-2013 E93 BMW 335i - Convertible
2012-2015 F30 BMW 335i 335iX - Sedan
2014-2016 F34 BMW 335iX - Gran Turismo
2014-2016 F32 BMW 435i 435iX - Coupe
2014-2016 F33 BMW 435i 435iX - Convertible
2014-2016 F36 BMW 435i 435iX - Gran Coupe
2011+ F10 BMW 535i 535i xDrive

Front Wheel Bearing Assembly - With Hardware is a critical component for maintaining the performance and safety of BMW vehicles. The wheel hub assembly connects the wheel to the chassis and features durable metal wheel bearings that facilitate smooth rotation as the car moves. Over time, these assemblies can wear out, leading to issues such as noise, vibration, and poor handling. Replacing the front wheel bearing assembly not only restores optimal vehicle performance but also enhances safety on the road.

Benefits:

• Optimal Performance: Ensures smooth and stable wheel rotation, improving overall vehicle handling and performance.
• Cost-Effective Replacement: Designed for easy installation in your garage, saving on professional labor costs.
• Durable Construction: Built with high-quality materials to withstand wear and provide long-lasting reliability.
• Improved Safety: Reduces the risk of wheel failure, enhancing safety while driving.
• Comprehensive Kit: Includes all necessary hardware for a complete and hassle-free installation.

Upgrade your BMW's performance and safety with the Front Wheel Bearing Assembly - With Hardware.