We are proud to bring out this truly awesome product that makes getting the required Flex Fuel hardware on your BMW with incredible ease and minimal effort, in your own driveway.

Our kit is entirely plug-and-play with the factory vehicle harness. No cutting or splicing of OEM wiring/connectors. It installs in minutes and can be removed without a trace on the car!

Our team used SolidWorks to design a Flow Optimized Flex Fuel Sensor Adapter (FFSA) to ensure fuel flow is unobstructed and with no added pressure drop at full fuel pump flow from the fuel tank to your motor when our kit is installed. This is important when pushing the factory fuel system with all the power Ethanol can provide over petrol!

Flex fuel sensor housing is designed to neatly install into the factory BMW fuel hat location.

Flex Fuel Sensor Adapter also contains two 1/8 NPT ports that allow installation of an auxiliary Fuel Pressure sensor for vehicles that don’t come with an OEM one from the factory for future use. Depending on fitment, either port can be used.

Install the bootmod3 Flex Fuel Plug and Play Kit and flash your flex fuel enabled bootmod3 OTS MultiMap or Custom Map in minutes and you’re off to the races never worrying about alcohol/petrol blend % in your fuel tank. It does not get better or easier than this!

bootmod3 FlexFuel Plug and Play Kit:

Minutes to install at home as opposed to hours at a shop with car up on lift fabricating/cutting into factory fuel lines and splicing/cutting/pinning into OEM electrical

4+ hours in time/cost savings to get going on Flex Fuel as compared to most other kits that require making custom fuel lines, fittings, and custom wiring! 

Fully reversible/removable and back to stock without a trace in minutes

Custom 3-piece Aluminum-6061 Flex Fuel sensor adapter with built-in sensor bypass to allow for obstruction-free fuel flow made to fit in the vehicle factory fuel hat area below the rear seat

All connecting points are sealed with fuel-safe Viton O-rings

Flex Fuel Sensor Adapter housing provides additional 1/8 NPT ports for optional Fuel Pressure sensor addition to vehicles without a factory one for bootmod3 CustomROM v2 support

CANBUS Enabled Ethanol Content Analyzer (ECA) that integrates with bootmod3 CustomROM for complete and seamless conversion of your BMW to FlexFuel for bootmod3 Flex Fuel enabled OTS MultiMaps and custom tunes with your bootmod3 tuner of choice

Power/CANBus 4-wire plug-and-play harness

100% Fully Plug and Play harness to the BMW Fuel Controller connectors (EKP3) on S55, N55 vehicles

100% Fully Plug and Play harness on the BMW Body Domain Controller (BDC/FEM) connector on Gen1 F-series B48/B58

Continental Flex Fuel sensor 3-wire harness

Custom Aluminum-6061 CANBus Enclosure for the bootmod3 ECA board

Custom, kink-free teflon braided line allowing plug-and-play installation with the OEM fuel hat and factory 5/16” or 3/8” fuel feed line. No cutting or new lines required.

-6 AN fitting by Racetronix

Upgrade your Mini Cooper's hose clamping mechanism with the 3/8" (9mm) Band Hose Clamp from ECS. Designed for precision and durability, this clamp ensures a secure fit for hoses, preventing leaks and ensuring optimal performance. Crafted to meet high-quality standards, it provides reliable sealing and resilience against varying temperatures and pressures. Easy to install and engineered for long-term use, this hose clamp is an essential addition to maintain your Mini Cooper's functionality.

• Precision-engineered for Mini Cooper hoses
• Ensures a secure and leak-free fit
• Resilient against temperature and pressure variations
• Easy to install and durable for long-term use

B48 Muffler Delete - F30/F31/F32/F33/F36:

Arguably THE BEST modification for your N20/B48. This muffler delete sounds too good to be a 4 cylinder! The combination of N20/B48 and muffler delete surpasses all sound expectations from a 4-cylinder! Impressive direct-fit solution. With this new muffler delete you can transform the sound and driving experience of your f chassis. A simple installation that can be completed with hand tools gives you the ability to take your car to the next level at home in your garage!

The ECS muffler delete removes the heavy and restrictive factory exhaust muffler and replaces it with a high-flow, straight-through exhaust pipe. This adds a louder exhaust note in a simple, cost-effective way without replacing the entire exhaust system and is fully compatible with the OEM rear valance. The muffler delete creates a noticeable increase in exhaust sound and more exhilarating turbo noise, without adding significant drone at cruising speeds. As an added bonus, our muffler delete shaves off 21.0 lbs., weighing in at only 7.0lbs compared to the OEM muffler at 28.0lbs!

YoutTube Sound Clips Featured HERE:

Features and benefits:

Enhanced exhaust tone Simple installation (with instructions!) 21lb weight savings! (Factory muffler 28 lbs, muffler delete 7 lbs!) Tip adjustment capability ​ Slide farther on for left and right adjustment Rotate for verticle adjustment Good looking and durable 304 stainless steel construction Heavy-duty fabricated sheet metal exhaust hangers Dual staggered tip exhaust tips (integrated) Installation and Support:

Installation is as easy as cutting, placing into position, and clamping! Tools you might want for the job: Exhaust hanger removal pliers - T379176 Exhaust pipe cutter - T385451 - CLICK HERE FOR INSTALLATION INSTRUCTIONS -

High-Performance Ignition Service Kit - Gen 1 B48/46 2.0L:

High performance ignition kit for your Gen 1 B46/48 featuring spark plugs, Turner high performance ignition coils and dielectric grease to make sure you have no issues at your next maintenance interval!

Our BMW ignition coils are designed with performance and efficiency in mind. An engine needs 3 main components to run (Air, Fuel, Spark.) Turner ignition coils are modified to increase energy output; more energy output results in a faster, more efficient and consistent burn to make sure your fuel is being utilized to its maximum potential. Our signature Turner ignition coils feature a blue housing that give your engine the performance and aesthetic your looking for.

Ignition coils should be changed every 40,000 - 60,000 miles and are an important maintenance item due to the essential role they play in your engines health, performance and efficiency. Choose Turner Ignition Coils to keep your engine running strong and healthy.

Features and Benefits:

Increased performance New spark plugs and grease Direct fitment Signature Turner Blue ignition coils

1/2"/12mm Band Hose Clamp

For reliable hose fastening, opt for the top-tier 1/2"/12mm Band Hose Clamp. Engineered for durability and versatility, this hose clamp ensures secure connections in various applications. Invest in quality and maintain optimal functionality with this essential accessory.

• Versatile clamp suitable for various hose sizes
• Durable construction ensures long-lasting performance
• Provides a secure seal for optimal functionality
• Easy to install and adjust for convenience

Made from a synthetic media that allows maximum filtration with minimal flow restriction to satisfy modern oil-hungry engines such as the N54 and N55.

Pro-GUARD D2 Oil Filters are the next generation in oil filter technology. Pro-GUARD D2 Oil Filters deliver increased flow and efficiency that are demanded from performance gas applications. This cartridge style filter comes with a built-in seal for a hassle free installation.