We are proud to present you with our long-awaited Turner Motorsport Carbon Fiber N55 Intakes. Like all of our Turner Motorsport products, our N55 intake was CAD Designed in-house to give you the best performing, most beautiful intake we could possibly imagine for your N55 powered BMW. The best part? Our design seamlessly integrates with OEM ducting and stock mounting locations to give you a simple install and an OEM+ fit and finish. We believe this is the way the N55 engine bays should have come from the factory. It’s time to ditch all that plastic.

Our higher flow filter and intake design gave our F30 335i an additional 7 WHP and 14 ft-lbs of torque over stock when we tested on our dyno. Our less restrictive intake design reduced post filter pressure by 0.2 psi over stock, allowing for gains across the entire RPM range - this reduced pressure drop also results in less stress on your N55’s turbo. Our enclosed intake also lowers your intake temperatures by 13 degrees over running an open intake.

We offer our N55 carbon intake in either gloss or matte finish, so you can choose what best suits your engine bay. Select either gloss or matte finish below, and then please select whether or not you are purchasing an intake for a manual transmission vehicle. If your vehicle has a manual transmission, it will require BMW Part # 13907515387.

If you are looking for our Turner Motorsport Open Carbon Intake, see T#568168

Download PDF Installation Instructions

Key Features & Benefits:

2x2 twill weave carbon fiber, clear coated for UV protection

Wrinkle Black Powder Coated heat shield

Ovaled Intake tube for OEM quality fitment

High flow cleanable Turner Motorsport air filter

+7 WHP / +14 lb-ft of torque!

Lowers intake temperatures by 13 degrees over running an open intake.

Special care instructions:

If clear coat gets scratched, reseal affected area with clear coat touch up

To retain UV resistance and protect finish, wax with high quality carnuba wax

Our N55 Carbon Intake fits the following BMWs:
2014 - 2016 F22 M235i, M235i xDrive
2012 - 2015 F30 335i, 335i xDrive
2012 - 2015 F32 435i, 435i xDrive

Want more in-depth details? We’ve got you covered below:

Carbon Fiber Intake Lid:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Reduces intake temperatures by 13 degrees compared to running an open intake

Carbon Fiber Intake Tube:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Ovaled intake tube design allowing

MAF scaling matches factory intake

MAF sensor flange machined from 6061-T6, black anodized and bonded to the intake tube directly in the center of the tube for accurate temp/airflow reading

Vacuum line port machined from 6061-T6, black andozed and bonded to intake tube

Integrated carbon flange allows secure mounting of intake tube to our heat shield

Heat shield:

One piece design manufactured from 12 gauge 5052 aluminum

Wrinkle black powder coated

Supplied gold heat shield tape

High Flow Air Filter:

Conical high flow cleanable air filer

8 ply oiled cotton gauze

Bellmouth filter flange inlet reduces turbulence and maximizes flow

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

Silicone Coupler - Straight 3" ID (76.20mm) x 3" L

No matter the project, ECS Tuning silicone couplers and elbows offer a high-quality, precision-engineered solution to your needs. Whether you're installing an intercooler, fabricating a custom intake system, or whatever else you can dream up, ECS Tuning has you covered.

• High-quality silicone construction for durability
• Precision-engineered design ensures a perfect fit
• Versatile solution for various automotive projects
• Enhances performance and reliability
• Compatible with BMW and other vehicles

Upgrade your BMW's air intake system with the Turner Motorsport Exact-Fit High Flow Oiled Air Filter! This performance filter replaces your factory air filter, providing better airflow for improved engine breathing, increased power, and enhanced fuel economy. It's a direct replacement for the OEM filter, ensuring easy installation and immediate performance gains.

Benefits:

• Higher airflow than stock paper filters
• Reusable design saves money on filter replacements
• Oiled filter offers superior airflow compared to dry filters
• Requires cleaning only every 50,000 miles under normal highway driving conditions
• Compatible with vehicles equipped with MAF sensors

Key Features:

• Direct replacement for the OEM filter
• Oiled air filter for maximum airflow
• Reusable design for long-lasting performance
• Easy maintenance with occasional cleaning

Ensure your BMW performs at its best with the Turner Motorsport Exact-Fit High Flow Oiled Air Filter!

ECS Silicone Coupler

Upgrade your BMW with the ECS Silicone Coupler. This straight 3 5/8" ID (92mm) x 3" L coupler is designed to enhance your vehicle's performance and durability. Crafted from high-quality silicone, it ensures long-lasting reliability and superior performance.

• Enhances vehicle performance
• Durable construction for long-lasting reliability
• Specifically designed for BMW vehicles