BMW Engine Parts

BMW Ignition Coil with Spark Plug Connector (ELDOR)

T#:641259

Part#: 12138657273

In Stock

$ 34.99 USD

Add to Wish List

Qty

$ 34.99 USD

Add to Wish List

Used in a wide variety of BMW engines to ensure proper spark plug operation.

Eldor Ignition Coil - 12138616153

T#:29234309

Part#: 12138616153

In Stock

$ 43.99 USD

Add to Wish List

Qty

$ 43.99 USD

Add to Wish List

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

Show More Show Less

Ignition Coil - Priced Each B46 & B48 2.0L B58 3.0L

T#:590050

Part#: 12138643360

In Stock

$ 39.99

This product was last offered at the strikethrough price on
06-15-2026

$ 36.76 USD

Add to Wish List

Qty

$ 36.76 USD

Add to Wish List

Revitalize your BMW's performance with Eldor ignition coils. Sluggish acceleration, misfires, and rusty terminals may indicate a worn coil. Located on the engine's top, these coils require inspection and replacement every 60,000 miles or as needed. Ensure your ignition system is in optimal condition for peak performance.

Revitalize sluggish acceleration
Address misfires and rusty terminals
Inspection and replacement every 60,000 miles
Harmonize ignition system components
Unlock hidden horsepower
Improve fuel economy

Show More Show Less

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

T#:2206

Part#: 201-6102

In Stock

$ 119.99

This product was last offered at the strikethrough price on
10-01-2026

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

In Stock

$ 212.99

This product was last offered at the strikethrough price on
10-12-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

19% off MSRP $ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Qty

19% off MSRP

$ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP Connecting Rod Bolt Kit - E9X M3 S65

T#:2434

Part#: 201-6001

In Stock

20% off MSRP $ 570.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 453.99 USD

Add to Wish List

Qty

20% off MSRP

$ 570.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 453.99 USD

Add to Wish List

NEW & REVISED!!! ARP has released a new version of their race-grade M3 connecting rod bolts and its better than ever before. If you're replacing your rod bearings these rod bolts are far superior to standard the OE BMW fasteners in terms of durability and ability to withstand stresses. This set of rod bolts is made specifically for the S65 4.0 liter V8, as found in the 2008-2013 M3 and replaces the previous ARP kit part number RBK_S65.

Show More Show Less

E46 M3 Schrick DLC-Coated Rocker Arm

T#:342372

Part#: 041513800

In Stock

$ 263.99

This product was last offered at the strikethrough price on
07-07-2026

$ 165.00 USD

Add to Wish List

Qty

$ 165.00 USD

Add to Wish List

The roller rocker arms transfer the rotational force of the camshaft to open the intake and exhaust valves. One end is raised and lowered by the rotating lobe of the camshaft, while the other end acts on the associated valve stem. If a roller rocker arm has failed you may experience a constant ticking noise during engine operation, or alternatively if the rocker arm has broken, you will receive multiple misfires and a rough running engine.

Show More Show Less

ARP Main Stud Kit for M50/M52 and S50/S52 (US)

T#:2208

Part#: 201-5000

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP main stud set for the 24 valves M50-based 6 cylinder engines (including M50, M52, S50US and S52US) and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes aerospace quality nuts. The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over. *Does not include washers*

Show More Show Less

ARP Connecting Rod Bolt Kit for E46 M3, MZ3 (M11 Size)

T#:2211

Part#: 201-6103

In Stock

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

Rogue Engineering Stainless Steel S54 Vanos Line - E46 M3, Z3 M, Z4 M...

T#:567568

Part#: S54VAN

Back Ordered

$ 59.00 USD

Add to Wish List

Qty

$ 59.00 USD

Add to Wish List

Now that BMWs popular S54 engine (found in the 2001-06 BMW M3, 2001-02 MZ3 and 2007-08 MZ4) are getting older, it's important to keep an eye on particular items. One such point is the S54 Vanos oil line. Normally thought of as a worry-free item, it has proven to put the damper on many track days. Rogue's stainless steel braided VANOS line replaces the factory BMW part number 11367837614 (current MSRP from BMW is $128.08!) The high pressure (1200psi) control system of the S54 vanos system is used to ensure responsive and accurate camshaft adjustments. The added complexity of the high oil pressure used on the S54 vanos means more opportunities for failures. Some customers have encountered the high pressure hardline fail at the track, spraying oil all over their engine compartment, ending their day. Rogue Engineering's S54 Vanos Oil Line is built in their Upper Saddle River, NJ facility, and tested to over 3000psi. Using their stainless steel braided hose with the proper banjo fittings, this a direct replacement for the factory line. Like the factory line, the lower portion of the line uses a heat sleeve from additional heat from the VANOS pump itself. Fits the following BMWs: 2001-06 BMW E46 M3 2001-02 BMW MZ3, including coupe and convertible 2007-08 BMW MZ4, including coupe and convertible

Show More Show Less

Glyco Connecting Rod Bearing Set

T#:375825

Part#: 11241284849

Ships in 1 Business Day

$ 92.02

This product was last offered at the strikethrough price on
07-15-2026

$ 85.59 USD

Add to Wish List

Qty

$ 85.59 USD

Add to Wish List

Standard bore - 45mm

BMW M20 Engine ARP Head Stud Kit - E30 325i, E34 525i

T#:189783

Part#: 201-4305

In Stock

$ 271.99

This product was last offered at the strikethrough price on
09-24-2026

$ 271.18 USD

Add to Wish List

Qty

$ 271.18 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1985-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

Glyco "Yellow" Crankshaft Bearing Shell - Set - E28, E30, E34, E36, E...

T#:375823

Part#: 11211706847

In Stock

$ 136.06

This product was last offered at the strikethrough price on
07-15-2026

$ 126.82 USD

Add to Wish List

Qty

$ 126.82 USD

Add to Wish List

Standard bore

Rod Bearing - E30 M3, E28 M5, E24 M6, E34 M5 (sold individually) ...

T#:183

Part#: 11241310515

In Stock

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 30.59

This product was last offered at the strikethrough price on
05-03-2026

$ 27.99 USD

Limited Qty Sale

Add to Wish List

E30 M3, E28 M5, E24 M6, E34 M5 Rod Bearing. Sold individually. Standard sizing.

This item fits the following BMWs
1988-1991 BMW E30 M3 - 8 required.
1988 BMW E28 M5 - 12 required.
1989-1993 BMW E34 M5 3.6 liter - 12 required.
1987-1989 BMW E24 M6 - 12 required.

Show More Show Less

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships in 7 Business Days

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

OEM Eldor Ignition Coil - BMW F9X G30 G14/15/16 G05 G06 G07 N63 S63 S...

T#:30927351

Part#: 12138692611

Ships in 1 day

$ 61.08 USD

Add to Wish List

Qty

$ 61.08 USD

Add to Wish List

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares. When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand and many other high-quality OEM brands with pride and has the parts you need to complete your next project with confidence. Sold per coil. Includes boot and connector.

Show More Show Less

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

ARP Connecting Rod Bolt Kit for E36 325 with 53mm Rod Bolt

T#:2186

Part#: 201-6301

In Stock at Vendor

20% off MSRP $ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Qty

20% off MSRP

$ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 53mm length factory BMW rod bolts with part number 11-24-1-713-342 (11241713342) which was used on SOME of the M50 2.5 liter engines from 1992-1995. Check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 44mm rod bolts, you will require kit part# 201-6201 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 53mm rod bolts only ***

Show More Show Less

Beru Glow Plug Preheating Module - E70, E90, F10

T#:584875

Part#: 12218591724

In Stock

$ 185.00

This product was last offered at the strikethrough price on
08-13-2026

$ 126.99 USD

Add to Wish List

Qty

$ 126.99 USD

Add to Wish List

Sends power to the glow plugs to preheat them for ignition.

ARP Rod Bolt Kit - S85

T#:1637703

Part#: 201-6002

Ships on Nov 3, 2026

$ 569.99 USD

Add to Wish List

Qty

$ 569.99 USD

Add to Wish List

ARP Head Stud Kit - N54

T#:24112781

Part#: ARP-HSK-N54-S

Back Ordered

$ 499.99 USD

Add to Wish List

Qty

$ 499.99 USD

Add to Wish List

ARP ARP2000 Head Stud Kit - N55

T#:42335661

Part#: ARP-HSK-N55-S

Ships in 3 Business Days

$ 743.99 USD

Add to Wish List

Qty

$ 743.99 USD

Add to Wish List

Enhance your BMW N55 engine's ability to handle higher levels of boost with 5150's custom-designed Head Stud Kit from ARP, the global leader in fastener technology!

ARP Main Stud Kit for E30 M3 S14 Engine

T#:2207

Part#: 201-5001

In Stock

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

This ARP main stud set for the E30 M3 eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each S14 main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
1988-1991 E30 M3 - S14 engine
1984-1985 E30 318i (M10)

Show More Show Less

Main Bearing Set - Standard Size - E30 M3 2.3 liter

T#:3166

Part#: 11210666110

Ships in 3 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

This E30 M3 Main bearing set is in standard size for the 2.3 liter S14 engine. This main bearing kit includes the thrust bearings.

This item fits the following BMWs:
1988-1991 E30 BMW M3

Show More Show Less

ARP Cylinder Head Stud Kit - Custom Age 625+ - BMW B58 3.0L

T#:25241791

Part#: B58-CA-203-4706

In Stock

20% off MSRP $ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

Qty

20% off MSRP

$ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

The Custom Age 625+ is made from a material that has a tensile strength of 260 ksi, which is substantially higher than the 190 ksi of the ARP 2000 head stud. It's an ideal choice for individuals who want to push the limits of their B58 builds and require a stronger head stud.

Show More Show Less

ARP Connecting Rod Bolt Kit for E30 M3 2.3 liter

T#:2187

Part#: 201-6104

In Stock at Vendor

$ 175.99 USD

Add to Wish List

Qty

$ 175.99 USD

Add to Wish List

Set of 8 Pro-Series connecting rod bolts, made by ARP -- the world leader in fastener technology. ARP Pro Series connecting rod bolts are precision CNC-machined to exacting specifications and designed for optimum reliability. Heat-treated with threads which are rolled to provide up to ten times more fatigue strength, these rod bolts are far superior to standard OEM BMW fasteners in terms of durability and ability to withstand stresses. This rod bolt set is specifically for the E30 M3 S14 2.3 liter engine.

Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1988-1991 E30 M3 - S14 4 cylinder

Show More Show Less

Rogue Engineering Power Pulley Set - E9X M3 (05/2008+)

T#:553839

Part#: PP.S65.V8.B

Ships in 6 Business Days

$ 295.00 USD

Add to Wish List

Qty

$ 295.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Show More Show Less

Rogue Engineering Power Pulley Set - S54 - E46 M3, Z3/Z4 M

T#:553971

Part#: PP.S54

In Stock

$ 259.00 USD

Add to Wish List

Qty

$ 259.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Show More Show Less

ARP Cylinder Head Stud Kit - E9X M3 S65

T#:554124

Part#: 201-4307

Back Ordered

$ 363.99 USD

Add to Wish List

Qty

$ 363.99 USD

Add to Wish List

ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Show More Show Less

ARP Head Stud Kit B48 Undercut CA625+, 12pt

T#:48367044

Part#: 401-4704

Ships on Oct 28, 2026

$ 588.99 USD

Add to Wish List

Qty

$ 588.99 USD

Add to Wish List

ARP Cylinder Head Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105898

Part#: 201-4701

In Stock at Vendor

20% off MSRP $ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

Qty

20% off MSRP

$ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

For engine builders crafting a high-performance powerhouse, the ARP Cylinder Head Stud Kit is the industry-standard choice for reliability and strength. Each kit features studs, nuts, and washers manufactured from ARP’s proprietary ARP2000 alloy, a material rated far superior to standard aircraft-quality steels.

Show More Show Less

ARP Harmonic Damper Bolt Set - BMW S58

T#:49092362

Part#: ARP-CBS-S58

Ships in 3 Business Days

$ 134.99 USD

Add to Wish List

Qty

$ 134.99 USD

Add to Wish List

The OE crank bolts are grade 10 torque-to-yield bolts, designed for only a single use. For vehicles making stock power, the stock bolts are more than enough. Unfortunately, vehicles making more power than stock have experienced issues with the stock damper bolts coming loose and breaking, leading to engine and crank damage. 5150 AutoSport worked with ARP to create this ARP Harmonic Damper Bolt Set to address this issue. These upgraded bolts are stronger than the factory bolts and are designed to provide even repeatable torque load, preventing them from breaking and allowing them to be re-torqued as needed.

Show More Show Less

BMW S14 Engine ARP Head Stud Kit - E30 M3

T#:189786

Part#: 201-4605

In Stock at Vendor

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

Rogue Engineering Power Pulley - E46 (Non-M)

T#:554021

Part#: P.E46

Back Ordered

$ 225.00 USD

Add to Wish List

Qty

$ 225.00 USD

Add to Wish List

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent. The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories. These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

Show More Show Less

Schrick Camshaft - M20 288 degree

T#:3501

Part#: 05601880-00

Ships on Dec 18, 2026

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

SEE T#338236

Schrick - S54 Intake Camshaft (288 Degree, 12.5mm Lift)- E46 M3, Z3M,...

T#:3572

Part#: TMS3572

Ships on Dec 18, 2026

$ 1,775.98 USD

Add to Wish List

Qty

$ 1,775.98 USD

Add to Wish List

E46 M3 Schrick 288 Degree Intake Camshaft with 12.5mm valve lift. Originally desinged for the M3 CSL but works great in a standard M3. A new rocker arm is required (Schrick or new BMW part #11337833259). This is a more agressive cam that the Schrick 280 degree cam that we also offer for the E46M3

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick - S55 Performance Camshaft Set - 238/272 - F80 M3, F82/83 M4 ...

T#:637691

Part#: SCHCSSS55238/272

Back Ordered

$ 1,899.99 USD

Add to Wish List

Qty

$ 1,899.99 USD

Add to Wish List

High-performance camshafts are key to increasing the top-end power output of your S55 engine at high boost. 238/272 degree, 10.6mm/10.5mm lift. Perfectly compatible with OE valves, springs, VANOS, Valvetronic etc

Show More Show Less

Pro Series Connecting Rod Bolts N12 N14 N16 N18 1.6L Engine

T#:594611

Part#: 201-6305

In Stock

$ 84.99 USD

Add to Wish List

Qty

$ 84.99 USD

Add to Wish List

Upgrade your MINI Cooper's engine with Pro Series Connecting Rod Bolts designed for N12, N14, N16, and N18 1.6L engines. Crafted from hardened ultra-strength steel by ARP, these rod bolts play a crucial role in maximizing the power output of your engine. Whether you're keeping your MINI stock or pushing it to higher power levels, these bolts ensure sufficient strength and durability for your bottom end.

Hardened ultra-strength steel construction
Compatible with OEM connecting rods or aftermarket options with similar through-bolt fastening
Essential upgrade for maximizing power output and ensuring engine longevity

Show More Show Less

MINI 1.6 W10/W11 Engine ARP Head Stud Kit

T#:212677

Part#: 201-4301

In Stock

$ 156.99 USD

Add to Wish List

Qty

$ 156.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following MINIs:
2002-2006 R50 MINI MINI Cooper
2002-2006 R53 MINI MINI Cooper S

Show More Show Less

Glyco Main Bearing Set (Standard) - E21, E28, E30

Features All Single-Tang Main Bearings for Earlier M20 Engines

T#:1196183

Part#: 11211722342

In Stock

$ 259.99

This product was last offered at the strikethrough price on
05-03-2026

$ 234.99 USD

Add to Wish List

Qty

$ 234.99 USD

Add to Wish List

MINI 1.6 N12/N14/N16/N18 Engine ARP Head Stud Kit

T#:189781

Part#: 201-4304

In Stock

$ 227.99 USD

Add to Wish List

Qty

$ 227.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

Schrick - S52/M52 Exhaust Camshaft (256 Degree/10.6mm Lift) E36 M3, Z...

T#:300485

Part#: 261.A1.561-02.C

In Stock

$ 1,401.99 USD

Add to Wish List

Qty

$ 1,401.99 USD

Add to Wish List

ARP Main Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105897

Part#: 201-5402

In Stock

10% off MSRP $ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 210.99 USD

Limited Qty Sale

Add to Wish List

Qty

10% off MSRP

$ 233.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 210.99 USD

Limited Qty Sale

Add to Wish List

This ARP main stud set for the 24 valves B58 6 cylinder engines and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design, and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts. Replaces BMW part number 11118604584 The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

Ignition Coil Pack - R50 / R52 / R53

T#:23383348

Part#: 12137510738

Ships in 6 Business Days

$ 92.99 USD

Add to Wish List

Qty

$ 92.99 USD

Add to Wish List

Is your Mini experiencing sluggish acceleration or misfires? It might be time to check the coil pack. The coil pack plays a crucial role in the ignition system and can affect engine performance. Replace it as necessary or ideally every 100,000 miles to keep your Mini's ignition system operating smoothly.

Show More Show Less

Schrick - S54 Exhaust Camshaft (280 Degree, 12.5mm Lift) - E46 M3, Z3...

T#:1259

Part#: TMS1259

In Stock

Sale - Save 5% $ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

Qty

Sale - Save 5%

$ 1,775.98

This product was last offered at the strikethrough price on
07-07-2026

$ 1,687.18 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Schrick Exhaust Camshaft - E46 M3, MZ3, MZ4 (S54) - 280 Degree, 12.5m...

T#:338216

Part#: TMS1259

Ships on Feb 1, 2027

Starting at $ 2,432.99 USD

Add to Wish List

Starting at $ 2,432.99 USD

Add to Wish List

E46 M3 Schrick 280 Degree Exhaust Camshaft with 12.5mm lift. This was originally desinged for the M3 CSL but works great in the standard M3. This cam is slightly more agressive than the "original" Schrick 272 degree (which we also offer). A new rocker arm is required (Schrick or new BMW part #11337833259).

BMW Schrick Technical Specs

Schrick Technical Information / Specs

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe
2006-2008 E85 BMW Z4 M Roadster M Coupe

Show More Show Less

Extended Spark Plug Socket

T#:391150

Part#: SUU884506

In Stock

9% off MSRP $ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

Qty

9% off MSRP

$ 31.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 28.99 USD

Add to Wish List

3/8" drive socket with 5/8" opening for most spark plugs

Cam Sprocket Bolt Kit for MINI W10 W11 1.6L Engine

T#:26404847

Part#: 206-1001

In Stock

$ 38.99 USD

Add to Wish List

Qty

$ 38.99 USD

Add to Wish List

Enhance the strength and reliability of your Mini's engine with the ARP Main Stud Kit. Engineered to exceed aerospace specifications, these main studs provide superior durability and performance for your engine build. Prevent camshaft flex and ensure optimal torque down for all main caps with ARP's high-quality hardware.

Benefits:

Exceeds aerospace specifications for superior strength
Prevents camshaft flex for improved engine performance
Ensures optimal torque down for all main caps
Complete kit includes main bolts and hardened washers for convenience

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results