BMW Engine Parts

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

T#:2206

Part#: 201-6102

Back Ordered

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

MHD Tuning CAN FlexFuel Analyzer - G-Chassis B58/S58

For vehicles with an Automatic Transmission only

T#:17937420

Part#: ECA-G-B58-S58-AT

In Stock

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

Upgrade your BMW's fueling system with the CAN Ethanol Content Analyzer from Turner Motorsport. This analyzer reads data from the E85 sensor and converts it to CAN format, enabling the DME to make accurate fueling decisions based on E85 content. Utilizing this analyzer alongside MHD or ECUTEK tunes allows you to activate a FlexFuel-like feature, optimizing performance and efficiency. Protect your engine from potential damage by ensuring your tune supports the FlexFuel feature for the E85 blend you're using.

Plug and play installation, no manual wiring or plumbing required

High-quality hoses tested with 10 bars of static pressure (145 Psi)

Each unit undergoes testing before leaving the manufacturer

Compatible with MHD or ECUTEK tuning solutions

Works with the stock or TU High-Pressure Fuel Pump

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

Back Ordered

$ 212.99

This product was last offered at the strikethrough price on
04-02-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

19% off MSRP $ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Qty

19% off MSRP

$ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP Connecting Rod Bolt Kit - E9X M3 S65

T#:2434

Part#: 201-6001

In Stock

$ 533.99

This product was last offered at the strikethrough price on
02-28-2026

$ 460.99 USD

Add to Wish List

Qty

$ 460.99 USD

Add to Wish List

NEW & REVISED!!! ARP has released a new version of their race-grade M3 connecting rod bolts and its better than ever before. If you're replacing your rod bearings these rod bolts are far superior to standard the OE BMW fasteners in terms of durability and ability to withstand stresses. This set of rod bolts is made specifically for the S65 4.0 liter V8, as found in the 2008-2013 M3 and replaces the previous ARP kit part number RBK_S65.

Show More Show Less

MHD Tuning CAN FlexFuel Analyzer - F-Chassis B48 B58 N55 S55 ...

For vehicles with an Automatic Transmission only

T#:17937419

Part#: ECA-F-B58-AT

In Stock

$ 490.00 USD

Add to Wish List

Qty

$ 490.00 USD

Add to Wish List

Upgrade your BMW's fueling system with the CAN Ethanol Content Analyzer from Turner Motorsport. This analyzer reads data from the E85 sensor and converts it to CAN format, enabling the DME to make accurate fueling decisions based on E85 content. Utilizing this analyzer alongside MHD or ECUTEK tunes allows you to activate a FlexFuel-like feature, optimizing performance and efficiency. Protect your engine from potential damage by ensuring your tune supports the FlexFuel feature for the E85 blend you're using.

Plug and play installation, no manual wiring or plumbing required

High-quality hoses tested with 10 bars of static pressure (145 Psi)

Each unit undergoes testing before leaving the manufacturer

Compatible with MHD, BM3, or ECUTEK tuning solutions

Works with any High Pressure Fuel Pump

Show More Show Less

ARP Connecting Rod Bolt Kit for E46 M3, MZ3 (M11 Size)

T#:2211

Part#: 201-6103

Back Ordered

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP Main Stud Kit for M50/M52 and S50/S52 (US)

T#:2208

Part#: 201-5000

Ships in 1 Business Day

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP main stud set for the 24 valves M50-based 6 cylinder engines (including M50, M52, S50US and S52US) and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes aerospace quality nuts. The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over. *Does not include washers*

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

BMW M20 Engine ARP Head Stud Kit - E30 325i, E34 525i

T#:189783

Part#: 201-4305

Ships in 1-2 days

$ 271.99

This product was last offered at the strikethrough price on
08-13-2026

$ 271.18 USD

Add to Wish List

Qty

$ 271.18 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1985-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships on Sep 2, 2026

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

Fuel injector and fuel supply rail caps

T#:5135630

Part#: AGA-CI-Y12

In Stock

$ 31.99 USD

Add to Wish List

Qty

$ 31.99 USD

Add to Wish List

Don't let dirt be the reason for bad fuel injectors.

THINKOBD 100

T#:2302720

Part#: 301050512

Ships in 1 Business Day

14% off MSRP $ 34.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 29.99 USD

Add to Wish List

Qty

14% off MSRP

$ 34.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 29.99 USD

Add to Wish List

This THINKOBD 100 obd2 car code reader can fast scan and clear trouble codes, even a beginner can use this unit to read the error code.

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

ARP Connecting Rod Bolt Kit for E36 325 with 53mm Rod Bolt

T#:2186

Part#: 201-6301

In Stock at Vendor

20% off MSRP $ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Qty

20% off MSRP

$ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 53mm length factory BMW rod bolts with part number 11-24-1-713-342 (11241713342) which was used on SOME of the M50 2.5 liter engines from 1992-1995. Check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 44mm rod bolts, you will require kit part# 201-6201 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 53mm rod bolts only ***

Show More Show Less

ARP Head Stud Kit - N54

T#:24112781

Part#: ARP-HSK-N54-S

Back Ordered

$ 499.99 USD

Add to Wish List

Qty

$ 499.99 USD

Add to Wish List

N54 Turbo Boost Leak Tester - BMW 3-Series E9X N54 3.0L

T#:641167

Part#: BMW-N54-CAP

In Stock

$ 49.00 USD

Add to Wish List

Qty

$ 49.00 USD

Add to Wish List

This Boost Leak Tester kit mounts inside both of the flexible intake hoses that lead to your turbo's compressor inlet flanges. You will need to remove the air box (or your aftermarket air filters) to expose the 2 intake pipes. Install the testers in each pipe and pressurize the system using the tire schrader with your tire inflation tool. The kit comes with the necessary caps to block the diverter valve return flanges on the intake pipes, also a cap to block the breather line at the bakc of the valve cover. Once the kit is installed, use compressed air to charge the system and you will see that both gauges read the compressor pressure you are filling with. You'll be able to test the turbo to the motor checking all leak points in between, including intercooler, clamped connections, intake manifold, divertor valves and the many random potential leak points. Note: Testing at the intake pipe, you may hear noise coming from the o-ring (at ~12 psi test pressure) that seals the intake pipe to the turbo inlet from debris. This is not a boost leak, these are not meant to see boost and not intended to be perfectly sealed, however hearing this hissing may be mis-diagnosed as a leak. In this case reduce the pressure. If no obvious leaks are heard in any other location, the test is complete and there are no significant leaks The gauge on the boost leak tester allows the user to: apply a safe amount of pressure to prevent injury or damage to the charge pipes or engine read how fast the system holds and bleeds air after removing the air source give a good comparison of compressor outlet air Vs. boost test air while pressurizing. The smaller the difference the lesser the air loss in the system Design Features: Plastic End Caps with 1/8" NPT threaded gauge port & fitting port Boost Gauges with 30 PSI / 1Bar Boost Gauge Universal Tire Schrader Valve (can be removed and tapped for 1/4" NPT thread fitting if desired) (2) Stainless Steel T-Bolt Clamps with Teflon lock-nut (3) Vinyl Caps for diverter valve return and valve cover breather

Show More Show Less

MINI R53 Sport Camshaft Single 263/267 - 219/223 - 10.00mm/8.50mm - 0...

T#:23284096

Part#: 1302469

In Stock

$ 413.99 USD

Add to Wish List

Qty

$ 413.99 USD

Add to Wish List

Enhance your BMW's engine performance with Cat Cams, crafted in Belgium to deliver outstanding performance at an affordable price point. Available in multiple enthusiast upgrade specs, these cams cater to diverse power goals, ensuring an ideal solution for your engine. Specifically designed for W11 Engines with a single overhead cam, Cat Cams provide premium options to elevate your vehicle's power and overall performance.

Show More Show Less

MINI R56 Sport Camshaft Pair 257/250 - 216/209 - 10.00mm/9.50mm - 0.0...

T#:18899191

Part#: 1302603

In Stock

$ 933.99 USD

Add to Wish List

Qty

$ 933.99 USD

Add to Wish List

Made in Belgium, Cat Cams are the epitome of high-quality performance at a reasonable price. These cams have been meticulously crafted to meet the demands of automotive enthusiasts, offering a diverse range of upgrade specifications to help you reach your power goals.

Cat Cams are designed specifically for N14 Engines, each of which features two overhead cams. These cams are the key to unlocking your engine's true potential. Please note that for optimal results, ECU reprogramming is required.

Elevate your engine's performance with Cat Cams and experience the true power of German engineering.

Show More Show Less

BMW S14 Engine ARP Head Stud Kit - E30 M3

T#:189786

Part#: 201-4605

In Stock at Vendor

$ 160.99 USD

Add to Wish List

Qty

$ 160.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1987-1991 E30 BMW M3

Show More Show Less

ARP Main Stud Kit for E30 M3 S14 Engine

T#:2207

Part#: 201-5001

In Stock

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

This ARP main stud set for the E30 M3 eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each S14 main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
1988-1991 E30 M3 - S14 engine
1984-1985 E30 318i (M10)

Show More Show Less

ARP Connecting Rod Bolt Kit for E30 M3 2.3 liter

T#:2187

Part#: 201-6104

In Stock at Vendor

$ 175.99 USD

Add to Wish List

Qty

$ 175.99 USD

Add to Wish List

Set of 8 Pro-Series connecting rod bolts, made by ARP -- the world leader in fastener technology. ARP Pro Series connecting rod bolts are precision CNC-machined to exacting specifications and designed for optimum reliability. Heat-treated with threads which are rolled to provide up to ten times more fatigue strength, these rod bolts are far superior to standard OEM BMW fasteners in terms of durability and ability to withstand stresses. This rod bolt set is specifically for the E30 M3 S14 2.3 liter engine.

Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1988-1991 E30 M3 - S14 4 cylinder

Show More Show Less

ARP Cylinder Head Stud Kit - M30 BMW 3.0L 3.4L

T#:379415

Part#: 201-4602

In Stock at Vendor

$ 255.99 USD

Add to Wish List

Qty

$ 255.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

This item fits the following BMW Engines:
M30 3.0L 3.4L I6

Show More Show Less

407 Piece O-Ring Assortment

T#:1809147

Part#: W5202

In Stock at Vendor

$ 21.99 USD

Add to Wish List

Qty

$ 21.99 USD

Add to Wish List

Nitrile Butadiene Rubber

Universal Valve Spring Compressor

T#:1809130

Part#: W89409

In Stock at Vendor

$ 126.99 USD

Add to Wish List

Qty

$ 126.99 USD

Add to Wish List

For servicing overhead valve engine with cylinder head removed.

ARP Cylinder Head Stud Kit - E9X M3 S65

T#:554124

Part#: 201-4307

Ships in 7 Business Days

$ 363.99 USD

Add to Wish List

Qty

$ 363.99 USD

Add to Wish List

ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated, ensuring complete heat penetration, to increase the clamping load up to 200,000 psi. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Show More Show Less

ARP Rod Bolt Kit - S85

T#:1637703

Part#: 201-6002

Ships on Sep 8, 2026

$ 569.99 USD

Add to Wish List

Qty

$ 569.99 USD

Add to Wish List

Clean Oil Drain Plugs - M12 x 1.5mm

T#:5135644

Part#: AGA-CODP-12-15

In Stock

$ 99.00

This product was last offered at the strikethrough price on
06-22-2026

$ 93.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 99.00

This product was last offered at the strikethrough price on
06-22-2026

$ 93.99 USD

Limited Qty Sale

Add to Wish List

Change the way you change oil

ARP ARP2000 Head Stud Kit - N55

T#:42335661

Part#: ARP-HSK-N55-S

In Stock

$ 699.99 USD

Add to Wish List

Qty

$ 699.99 USD

Add to Wish List

Enhance your BMW N55 engine's ability to handle higher levels of boost with 5150's custom-designed Head Stud Kit from ARP, the global leader in fastener technology!

Cat Cams Sport Camshaft set 269/269 10.00mm - E30 318i E36 318i ...

T#:578594

Part#: 1301413

In Stock

$ 1,051.99 USD

Add to Wish List

Qty

$ 1,051.99 USD

Add to Wish List

Made in Belgium, Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in most popular enthusiast upgrade specs to ensure there is a option for what ever your power goal is.

ARP Main Stud Kit for BMW/MINI 1.6 N12/N14/N16/N18 Engine

T#:189787

Part#: 201-5401

In Stock at Vendor

$ 251.99 USD

Add to Wish List

Qty

$ 251.99 USD

Add to Wish List

This ARP main stud set for the new MINI F engines eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the MINI, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

ARP Cylinder Head Stud Kit - Custom Age 625+ - BMW B58 3.0L

T#:25241791

Part#: B58-CA-203-4706

Back Ordered

20% off MSRP $ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

Qty

20% off MSRP

$ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

The Custom Age 625+ is made from a material that has a tensile strength of 260 ksi, which is substantially higher than the 190 ksi of the ARP 2000 head stud. It's an ideal choice for individuals who want to push the limits of their B58 builds and require a stronger head stud.

Show More Show Less

ARP Harmonic Damper Bolt Set - BMW S58

T#:49092362

Part#: ARP-CBS-S58

Ships in 3 Business Days

$ 134.99 USD

Add to Wish List

Qty

$ 134.99 USD

Add to Wish List

The OE crank bolts are grade 10 torque-to-yield bolts, designed for only a single use. For vehicles making stock power, the stock bolts are more than enough. Unfortunately, vehicles making more power than stock have experienced issues with the stock damper bolts coming loose and breaking, leading to engine and crank damage. 5150 AutoSport worked with ARP to create this ARP Harmonic Damper Bolt Set to address this issue. These upgraded bolts are stronger than the factory bolts and are designed to provide even repeatable torque load, preventing them from breaking and allowing them to be re-torqued as needed.

Show More Show Less

ARP Cylinder Head Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105898

Part#: 201-4701

In Stock

20% off MSRP $ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

Qty

20% off MSRP

$ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

For engine builders crafting a high-performance powerhouse, the ARP Cylinder Head Stud Kit is the industry-standard choice for reliability and strength. Each kit features studs, nuts, and washers manufactured from ARP’s proprietary ARP2000 alloy, a material rated far superior to standard aircraft-quality steels.

Show More Show Less

N63 chain tensioning kit

T#:5175740

Part#: AGA-11-9-900-K

Ships in 7 Business Days

$ 249.00 USD

Add to Wish List

Qty

$ 249.00 USD

Add to Wish List

A must have for a timing job.

3/8" Dr. 5/8" Extended Spark Plug Socket

T#:2242226

Part#: W80533

Ships in 1 Business Day

$ 20.25 USD

Add to Wish List

Qty

$ 20.25 USD

Add to Wish List

Extended socket length reaches confined areas.

Piston Ring Comp 3-1/2" to 7"

T#:2242223

Part#: W80573

Ships in 1 Business Day

$ 22.99 USD

Add to Wish List

Qty

$ 22.99 USD

Add to Wish List

Use to install pistons on most passenger cars and truck engines

BMW E60 M5 Crank Case Test Cap

T#:6924319

Part#: AGA-6061-TC

Ships in 7 Business Days

$ 99.99 USD

Add to Wish List

Qty

$ 99.99 USD

Add to Wish List

BMW E60 M5 Crank Case Test Cap

The BMW E60 M5 Crank Case Test Cap is designed to facilitate accurate testing of crankcase pressure across a range of vehicle models. This versatile test cap is compatible with early and late model vehicles equipped with steel, aluminum, or plastic valve covers. Featuring a multi-diameter fitting, it connects directly to IMIBs, handheld manometers, and smoke machines, eliminating the need for adapters and ensuring precise readings without leaks.

Benefits:

Versatile Compatibility: Suitable for use with steel, aluminum, and plastic valve covers on early and late model vehicles.
Direct Connection: Multi-diameter fitting allows direct connection to IMIBs, handheld manometers, and smoke machines.
Leak Prevention: Eliminates the need for adapters, reducing the risk of leaks and inaccurate readings.
Enhanced Accuracy: Provides reliable crankcase pressure testing for better diagnostic results.

Show More Show Less

Cat Cams Upraded Camshafts - 268/268 - 230/230 - 10.45mm/10.45mm - 1....

T#:28271168

Part#: 1304214

Ships on Sep 25, 2026

$ 1,524.99 USD

Add to Wish List

Qty

$ 1,524.99 USD

Add to Wish List

Cat Cams Sport camshaft set 258/247 10.00mm/9.40mm - M60 V8 ...

T#:578583

Part#: 1303506

Ships on Sep 25, 2026

$ 2,233.99 USD

Add to Wish List

Qty

$ 2,233.99 USD

Add to Wish List

Made in Belgium, Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in most popular enthusiast upgrade specs to ensure there is a option for what ever your power goal is.

Main Stud Kit - M50/M52/S50/S52

T#:26171653

Part#: ARP-MSK-M50

Back Ordered

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the M50/M52/S50/S52 engines that were used in a variety of BMW models. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best. Installation Instructions: To ensure accurate torque readings and proper thread engagement, thoroughly clean all threads in the engine block. If necessary, use an ARP chaser to chase the threads. Before installing any hardware, carefully inspect and clean it for defects, shipping damage, and proper fit, length, and dimension. Gently screw the main studs into the engine block by hand until they are snug. Install the main caps, checking for any binding or misalignment. Apply ARP Ultra-torque fastener assembly lubricant to the threads of the studs, nuts, and washers. Install the washers and nuts onto the studs and tighten them by hand. It is highly recommended to use the ARP Ultra-torque fastener assembly lubricant provided with the kit, as it provides consistent clamping force and reduces friction on the studs. Do not use motor oil or other low-quality lubricants. PRELOAD (TORQUE) RECOMMENDATIONS 7. Following the manufacturer-recommended torque sequence tighten the nuts in steps 1-3 Step 1: Tighten to 20 ft-lbs. Step 2: Tighten to 40 ft-lbs. Step 3: Tighten to 60 ft-lbs. With the included ARP Ultra-Torque fastener assembly lubricant

Show More Show Less

Cat Cams Camshaft Set - 288/280 12.75mm/12.50mm Lift - E46 M3 With R...

T#:4414885

Part#: 1301805KIT

Special Order: No Guaranteed ETA

$ 4,372.99 USD

Add to Wish List

Qty

$ 4,372.99 USD

Add to Wish List

Made in Belgium, Cat Cams offer great performance at a reasonable price. Cat Cam offers cams in most popular enthusiast upgrade specs to ensure there is a option for what ever your power goal is. The included rocker arm kit consist of: - 24x "CAT031" rocker arm, steel billet, coated - 1x oil connector bridge - rocker arms with 0.5mm oil jet hole towards the cam/follower contact area - rocker arm shafts need to be drilled at each rocker arm (in the groove already present) - rocker arm shafts need to be drilled at oil bridge connector (no need to make extra groove, connector has internal groove) - intake rocker arm shaft needs front plug to close - intake rocker arm shaft has no oil feed so an oil bridge is required to connect the intake/exhaust rocker arm shafts *Please note that the factory cams ave a pressure regulator valve that needs to be removed and installed in the new cams*

Show More Show Less

Cam Sprocket Bolt Kit for MINI W10 W11 1.6L Engine

T#:26404847

Part#: 206-1001

In Stock

$ 38.99 USD

Add to Wish List

Qty

$ 38.99 USD

Add to Wish List

Enhance the strength and reliability of your Mini's engine with the ARP Main Stud Kit. Engineered to exceed aerospace specifications, these main studs provide superior durability and performance for your engine build. Prevent camshaft flex and ensure optimal torque down for all main caps with ARP's high-quality hardware.

Benefits:

Exceeds aerospace specifications for superior strength
Prevents camshaft flex for improved engine performance
Ensures optimal torque down for all main caps
Complete kit includes main bolts and hardened washers for convenience

Show More Show Less

ARP Head Stud Kit B48 Undercut CA625+, 12pt

T#:48367044

Part#: 401-4704

In Stock

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

ARP Main Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105897

Part#: 201-5402

In Stock at Vendor

20% off MSRP $ 292.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 233.99 USD

Add to Wish List

Qty

20% off MSRP

$ 292.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 233.99 USD

Add to Wish List

This ARP main stud set for the 24 valves B58 6 cylinder engines and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design, and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts. Replaces BMW part number 11118604584 The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

MINI 1.6 N12/N14/N16/N18 Engine ARP Head Stud Kit

T#:189781

Part#: 201-4304

In Stock

$ 227.99 USD

Add to Wish List

Qty

$ 227.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

Pro Series Connecting Rod Bolts N12 N14 N16 N18 1.6L Engine

T#:594611

Part#: 201-6305

In Stock

$ 84.99 USD

Add to Wish List

Qty

$ 84.99 USD

Add to Wish List

Upgrade your MINI Cooper's engine with Pro Series Connecting Rod Bolts designed for N12, N14, N16, and N18 1.6L engines. Crafted from hardened ultra-strength steel by ARP, these rod bolts play a crucial role in maximizing the power output of your engine. Whether you're keeping your MINI stock or pushing it to higher power levels, these bolts ensure sufficient strength and durability for your bottom end.

Hardened ultra-strength steel construction
Compatible with OEM connecting rods or aftermarket options with similar through-bolt fastening
Essential upgrade for maximizing power output and ensuring engine longevity

Show More Show Less

MINI 1.6 W10/W11 Engine ARP Head Stud Kit

T#:212677

Part#: 201-4301

In Stock

$ 156.99 USD

Add to Wish List

Qty

$ 156.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following MINIs:
2002-2006 R50 MINI MINI Cooper
2002-2006 R53 MINI MINI Cooper S

Show More Show Less

THINKDIAG (include 1 Free Software)

T#:2302718

Part#: 301180767

Ships in 1 Business Day

$ 101.99 USD

Add to Wish List

Qty

$ 101.99 USD

Add to Wish List

ThinkDiag is prefect to use with the unique THINKCAR app. Easy and convenient, anytime and anywhere.

AGA Tools N63 Updated Rear Engine Cover - BMW N63 (2008-2019) ...

T#:26404835

Part#: AGA-N63-6061-URC

Ships in 7 Business Days

$ 449.99 USD

Add to Wish List

Qty

$ 449.99 USD

Add to Wish List

The BMW N63 rear cover is a metal plate that covers the rear of the BMW N63 V8 engine. It helps to seal the engine and prevent oil leaks. Over time, the original sealing gasket becomes brittle and does not seal, causing leaks between the engine and transmission bell housing. This repair can be very expensive and is usually misdiagnosed for a rear main seal. The AGA Updated N63 Rear Cover is an inexpensive alternative, made of 6061 billet aluminum. This kit includes the rear cover, viton o-ring, alcohol wipe, scotch-brite pad and o-ring grease. BMW Part # 11142446298 & 11148483799 BMW Service Bulletin (SIB) 11 09 16

Show More Show Less

Project Cars

SELECT YOUR BMW

Sub-Categories

BMW E60 M5 Crank Case Test Cap

Benefits:

Benefits:

Select Vehicle

Purpose

Category

Brand

Price

Special Offers

Shipping

Narrow Results