If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.

The camshaft position sensor is essential for assisting the engine DME by monitoring the camshaft's position. The data from this sensor is key to optimizing ignition timing and ensuring smooth engine performance.

Often referred to as the CMP sensor, this component is crucial for the overall functionality of the powertrain. A failing camshaft position sensor can cause a range of issues, including engine stumbling, hesitation during acceleration, power loss, and even starting difficulties or complete failure to start.

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

Long lasting alternative for sealing plate 11367831906. This sealing flange is located between the VAN0S adjusting unit and the VAN0S solenoid on the S54 engine. It can be the source of oil leaks and should be replaced when the the VAN0S solenoid is.

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW M Roadster M Coupe (S54)
2006-2008 E85 BMW Z4 M Roadster M Coupe

This top-end gasket set covers the cylinder head on the S54 engine used in the E46 M3, Z3 M Roadster/M Coupe, and E85/E86 Z4 M Roadster, M Coupe. If you're pulling the head, intake manifold, or doing any other upper end engine work this set can be a time and money saver. This set includes all of the commonly replaced gaskets, seals, and o-rings when overhauling the head. It's also a useful kit to have and dip into any time you're doing upper end engine work. Not having a critical seal or gasket on hand can ruin your work and this gasket set can prevent that from happening. This Victor Reinz set includes the head gasket.

BMW #QtyDescription

071199035461left timing rail upper bolt seal

071199630724VAN0S oil line seal ring

071199631292crankcase vent banjo bolt seals

071199632522screw plug seal ring

071199633421right upper timing rail bolt seal ring

071199634181timing chain tensioner seal ring

111214373952valve cover stud grommet seal

1112783097213valve cover stud grommet seal

111278312716spark plug hole profile gasket

111278320341main valve cover gasket

111278370241oil fill cap seal ring

111278370251crankcaske oil separator seal ring

111417367581VAN0S-camshaft plate o-ring

111578309661crankcase oil separator o-ring, large

111578321191crankcase oil separator plug o-ring

113113173181inside o-ring for internal VAN0S regulating valve

113490644572valve stem seal, 2 sets = 24 valves

113678319381VAN0S unit profile gasket

114113060821outside o-ring for internal VAN0S regulating valve

115313184021thermostat-to-water pump o-ring

115378307083coolant pipe o-ring gasket

115378307092thermostat housing connector o-ring

116114076951intake bellows o-ring profile gasket

116178301041intake bellows-to-airbox gasket

116278306676exhaust manifold port gasket

117275052591air pump valve profile gasket

121417483982camshaft position sensor o-ring

135478314836throttle body o-ring

136414374746fuel injector o-ring, upper

136478306116fuel injector o-ring, lower

111278359181head gasket

This item fits the following BMWs:
2001-2006 E46 BMW M3
2001-2002 Z3 BMW Z3 M Roadster Z3 M Coupe
2006-2008 E85 BMW Z4 M Roadster Z4 M Coupe

Meet modern emission regulations while preserving engine performance with the ECS Baffled Oil Catch Can. Designed for BMW and MINI vehicles, this system efficiently captures blow-by gases, preventing excessive oil vapor ingestion into the intake tract. The innovative 4-chamber baffle system maximizes oil/air separation, reducing carbon build-up and pollutants. Featuring a 1/4" drain fitting for easy maintenance, this catch can minimizes oil deposits, ensuring cleaner emissions and enhanced engine performance.

Key Benefits:

• Efficient 4-chamber baffle system for maximum oil/air separation
• Recirculated design reduces oil ingestion, promoting cleaner emissions
• Durable 6061-T6 billet machined body with anodized black finish for longevity
• Integrated dipstick and sealed reservoir for easy oil inspection and maintenance
• Serviceable design with removable baffle plates for cleaning
• Easy installation with customizable mounting options and leak-free fittings
• Engineered and manufactured in the USA for superior performance and durability

Note: Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

ECS Tuning introduces the solution to your engine bay aesthetic concerns with the Billet Aluminum Oil Dipstick. Say goodbye to the bright red plastic eyesore and elevate your under-the-hood style effortlessly. Designed to OE specifications, this dipstick boasts an easy-to-read fill line and is available in three stunning finishes: black, polished, or clear anodized.

• Billet aluminum construction for enhanced durability
• Easy-to-read fill line for convenient oil level checks
• Available in three finishes: black, polished, or clear anodized
• OE specifications ensure a perfect fit
• Improved ease of insertion compared to factory ribbon dipstick
• Aesthetic enhancement for your engine bay

Upgrade your engine bay's appearance and functionality with the ECS Tuning Billet Aluminum Oil Dipstick. No more struggles reinstalling your dipstick; enjoy a sleek and high-performing addition to your vehicle.

Includes connector housing with terminals and seals. Commonly used for the engine oil level sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433915 - Commonly used for the engine oil level sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Fix oil leaks on your BMW's passenger side engine with Turner Motorsport's CPV O-ring replacement. The O-ring failure in the CPV typically leads to slow oil leaks, and now you can address this issue at a fraction of the cost by replacing the O-ring instead of the entire CPV. Unlike the OEM Buna rubber, the new Viton Fluoroelastomer used in this O-ring is resistant to higher temperatures, ensuring prolonged life without leaks.

• Cost-effective solution for oil leaks on the passenger side of the engine
• Replaces the CPV O-ring without replacing the entire CPV
• Viton Fluoroelastomer resistant to higher temperatures
• Prolonged life without leaks
• Addresses O-ring failure due to heat cycling and oil exposure

Upgrade your exhaust system with the Stainless Steel Oxygen Sensor (O2) Weld Bung (M18x1.5mm). This high-quality weld bung is made from stainless steel, ensuring durability and resistance to corrosion. It features M18x1.5mm threads, making it compatible with most oxygen sensors. Perfect for custom exhaust setups or replacing damaged bungs, this weld bung is a must-have for any automotive enthusiast.

• Made from high-quality stainless steel for durability and corrosion resistance
• M18x1.5mm threads ensure compatibility with most oxygen sensors
• Ideal for custom exhaust setups or replacing damaged bungs
• Essential for automotive enthusiasts looking to upgrade their exhaust system