BMW Suspension Parts for BMW Z3 (1996-2002)

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 215mm (8.46") to 275mm (10.82") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints(M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability

Whether you need a camber change or you are looking for more adjustment with your camber plates, you can change your camber by shimming the strut and spindle with the TMS bolt kit. There are some things to take into account with this kit so please read the installation tips below. An alignment is strongly recommended after installing this kit.

Click here for installation instuctions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2006-2008 E85 E86 BMW Z4 M Roadster M Coupe

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

You get the best of both worlds with this pair of Turner Motorsport adjustable sway bar links. We searched far and wide to find the hidden gem of swaybar links. You get the same quiet operation and long life as the stock links plus the strength and adjustability of rod-end style sway bar links.

With the wide range of suspensions and sway bars available today adjustable sway bar links can help you with many problems. Along with the ability to remove preload you can change the length to maximize sway bar geometry. Example: if the sway bar hoop comes too close to the steering rack, oil cooler, or under tray in its suspension travel you can adjust it by simply lengthening or shorting the adjustment rod. In some cases you may need a longer or shorter adjustment rod to achieve optimal geometry. We also offer these same links in other custom lengths (click here) that may not be specific to BMW chassis.

Features:

• Adjustable to neutralize preload on sway bar (balanced handling)
• The ability to set sway bar geometry and clearance
• Low friction ball joints
• High articulation
• Direct replacement for OEM sway bar links
• Watertight boot seal
• Ball joint is made by a world leader in ball joint technology, THK. THK's OEM Customers: BMW, Porsche, Ford, GM, Nissan, Honda, and Toyota

Turner Swaybar Link Specs:
TSU9912AF1: 220.00mm - 235.00mm / 8.66" - 9.25"
TSU4612AF3: 250.00mm - 265.00mm / 9.84" - 10.43"
TSU5012AF8: 280.00mm - 295.00mm / 11.02" - 11.61"
TSU9912A95: 290.00mm - 305.00mm / 11.42" - 12.00"

These adjustable sway bar end links can be used on a variety of BMWs. Please select your car below. Please note these end links do not fit non-M E36, except 325i/is produced before 6/1992.

Elevate Your BMW's Performance with ECS Tuning's Ultimate Performance Rear Shock Mount Kit

ECS Tuning presents the Ultimate Performance Rear Shock Mount Kit, specifically designed to address recurring rear shock mount blowouts experienced by various BMW models, including the M3 and non-M 3 Series dating back to the E30 chassis in 1984. This innovative kit provides a long-term solution, ensuring optimal damper performance and longevity while eliminating rear clunking noises and handling issues caused by blown shock mounts.

Key Benefits:

• Solves rear shock mount blowout issues on BMW models
• Allows full articulation of rear dampers for improved performance
• Industry-first design with PTFE lined stainless steel monoball spherical bearing
• 80A polyurethane isolation bushings reduce noise, vibration, and harshness (NVH)
• Lower dust seal enhances bearing life by preventing road debris ingress
• Corrosion-resistant anodized 6061-T6 construction for durability
• Compatible with 10mm, 12mm, or 14mm damper shafts

Upgrade your BMW's rear shock mounts with ECS Tuning's Ultimate Performance Rear Shock Mount Kit, providing superior performance, reduced NVH, and increased bearing longevity for a more controlled and comfortable ride.

These bushings have the hole off-center to give your car a little more track, caster, and camber. This style came as standard equipment on E30 M3s (8/89-later) and 1995 E36 M3 but will work with any E30, E36, Z3.

Rubber control arm bushings are designed to flex and absorb energy. That's fine on a streetcar but on an all-out racing machine you want your alignment to stay constant. We have picked Delrin for this application due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change) but decreasing bushing windup or drag (friction). They are not recommended for street-use but highly-recommended for track cars.

To save time, pick up a pair of new bushing carrier brackets and hardware. This will save you the time and hassle of pressing out the old bushings. This will especially save you time if you're buying new control arms at the same time (no time wasted removing the old brackets from the arms). Stainless steel set screws included.

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle.

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S50 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Want a race-spec rear shock mount but with the comfort of a factory bushing? This ECS rear shock mount combines the precision and articulation of a spherical bearing with the isolation of urethane bushings. The stainless monoball bearing is lined with PTFE lubricant and suspended in 80A urethane and housed in a hard anodized 6061-T6 aluminum mount. The spherical bearing is a better design than most rear shock mounts because it allows the shock to move and tilt without side-loading the shock shaft (which leads to premature failure of the shock). Most Genuine BMW and aftermarket shock mounts are not designed for shock angles and the stress that track or performance driving will put on the shock shaft. The ECS shock mount is properly designed to handle these loads. The internal bearing is also replaceable - it will be years before you have to replace the entire mount. The ECS mount is fully encapsulated to prevent the common shock mount failure of the stock mount design.

ECS RSM features:

• Maintenance free, PTFE lined, stainless steel monoball spherical bearing for full shaft articulation
• 80A polyurethane isolation bushings for NVH control
• Accommodates 10mm, 12mm, or 14mm damper shafts
• Fully constrained shaft mount makes RSM blow out impossible
• Hard anodized 6061-T6 construction
• Fully rebuildable design

* - the RSM comes with the BMW standard 10mm shock shaft bushings. 12mm is used on some performance shocks and 14mm is used on some true motorsport rear shocks.