BMW Brake Pads for BMW 7 Series E32 (1988-1994)

A high-performance street pad with much-improved braking performance and without the levels of dust from a factory pad. The Street 5.0 pads are perfect for drivers who don’t want an ordinary replacement pad and want something that will hold up during aggressive street driving. The Street 5.0 pads are similar to the established Hawk HPS pads but with more initial bite. While the HPS pads fill the need of a direct replacement OEM-type pad, the Street 5.0 kicks braking performance into the next gear. With the Street 5.0 pads you can expect:

• Better stopping power even when the pads are cold
• Good initial bite (more than on Hawk HPS)
• Excellent resistance to fade during street use
• Moderate dust during normal street driving
• Quiet operation
• Easy on rotors

Fits the following BMWs:
E32, E34, E36 M3, E46 M3, E39 528i 525i, Z3 M

Pagid's newest sprint racing pad was developed for racing cars achieving very high average speeds with short braking distances and functional aero. The RST pads feature very high friction levels for the quickest bite and highest fade resistance than any other Pagid pad. RST pads are broken into 5 levels and all have ranging bite and release characteristics. RST pads will trade low wear for torque output and faster response. These were developed based on the needs of race engineers in World Challenge, Daytona Prototype, and GTLM where functional aero meant high grip in the corners and smaller braking zones.

RST Brake Pad Types:

• RST1 -  Very high friction coefficient, high initial bite, progressive torque curve, very high fade resistant
• RST2 - Medium high friction coefficient, good initial bite, mild progressive torque curve, good pedal feel
• RST3 - High friction coefficient, good initial bite, low heat conductivity, excellent modulation and release characteristics
• RST4 - Medium friction coefficient, good initial bite, mild progressive torque curve, high heat tolerance with consistent feel
• RST5 - Optimum thermal management, absolutely fluid fade resistant, highly developed recovery properties, extremely high friction coefficient

This item fits the following BMWs:
1995-1998 E36 BMW M3 
2001-2006 E46 BMW 330i M3 
1989-1995 E34 BMW 525i 530i 535i 540i M5 
1988-1994 E32 BMW 735i 735il 740i 740il 750il 
1997-2002 Z3 BMW M Roadster M Coupe
2006-2008 Z4 BMW M Roadster M Coupe

Brake pad wear sensor should be replaced at ever brake service, even if not worn down. This ensures the sensor is as new as possible and less likely to fail due to built up corrosion.

Fits the following BMWs:
E31 850Ci - Rear
E32 735i/iL 740i/iL 750iL - Front and Rear
E34 525i 535i 530i 540i M5 - Front and Rear

The latest in the Yellow line takes all of the RSL29 characteristics and adds a bit more aggressive behavior. Friction levels go up for more initial bite and better fade resistance. Modulation and release stays close to RSL29 levels. Pad and rotor wear is a little more than on the previous Yellows but still within reasonable levels and the RSL1 is still considered an extended endurance pad. Its development stemming from GT classes at Le Mans and Nürburgring.

Since Pagid pads tend to "out-gas" we recommend using these pads with a new gas-slotted or cross-drilled rotor for the best performance. Pagid brake pads are not compatible with previously used rotors, especially if used with a carbon or Kevlar based race pad.

This item fits the following BMWs:
1995-1998 E36 BMW M3 
2001-2006 E46 BMW 330i M3 
1989-1995 E34 BMW 525i 530i 535i 540i M5 
1988-1994 E32 BMW 735i 735il 740i 740il 750il 
1997-2002 Z3 BMW M Roadster M Coupe
2006-2008 Z4 BMW M Roadster M Coupe