Emissions System for BMW 3 Series E46 (1999-2005)

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition.

The factory hoses offered through BMW are plastic and will yield the same results of becoming brittle and damaged over time. Our solution is a premium replacement that will outlast everyone of the OEM replacements. Our Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling

Design:

Retains OEM hose end fittings to ensure proper seal

“Black” 3 ply reinforced silicone w/ “White” Turner logo

Our engineers at Turner sought out to solve the degrading issues that happens with the factory crankcase vent hose and found the best solution is a silicone replacement. Our Turner Silicone Crankcase Vent Hose can be used to replace the factory brittle hose to prevent vacuum leaks and lackluster performance. Simply take your factory crankcase vent hose and remove the ends; the factory ends can be installed on the new Silicone Vent Hose with the supplied clamps for a tight seal.

Turner Silicone Crankcase Vent Hose replaces the following part #'s:

CSL Vent Hose (11157833649) - Silicone Crankcase Vent hose is a direct replacement
Non-CSL Vent Hose(11157831311) - Silicone hose will make a "U" bend with direct fitment and can also be trimmed for your own preferable fit.

- Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose that is susceptible to cracking overtime from constant heat cycling
- Design:

Turner logo forward facing when hood is open
Retains OEM hose end fittings to ensure proper seal and reduce cost
“Black” 3 ply reinforced silicone w/ “White” Turner logo
includes 2 German style 430 stainless worm-drive clamps for installation
- Special care instructions:

Do not overtighten hose clamps, hand tight is recommended.
Carefully cut the OEM plastic casing from both plastic fittings for reuse

Modern day emissions regulations require the use of a closed crankcase ventilation (PCV) system to recirculate combustion blow-by gases from the crankcase back in to the intake to be burned.  Unfortunately, these blow by gases contain water vapor (which is a byproduct of combustion) and pick up oil mist from and the windage cloud and cam lubrication system as they travel through the crank case.  Due to less than 100% effective air/oil separation in the stock PCV system, some oil mist and water vapor gets carried back to the intake tract and over time cause oil deposits in the intake manifold, intake ports, and on the back of intake valves.  All will eventually lead to poor performance and reduced fuel economy, and the presence of this oil mist in the intake charge may even increase the risk of engine-damaging detonation. 

With forced induction, track use, and/or extended high RPM usage, these symptoms increase as the factory PCV system is overwhelmed, and a catch can becomes a must for your E46 M3. This kit is a direct fit making this an easy reversal if desired as well as maintaining a clean appearance by utilizing the open "smuggler's compartment" on the passenger side of the engine bay.

*Click here for catch can instructions*

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton o-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Valved drainage system - no removal of can necessary to empty

A combination of billet fittings and AN lines for an upgraded and serviceable crankcase vent hose. Attaches between the oil separator and the CSL air box.

The factory rubber/plastic hoses become brittle and crack over time. Brittle and cracked hoses can cause multiple vacuum leaks that are impossible to repair without hose replacement. Vacuum leaks can cause many problems including rough running, missing, stalling at idle, and even a no-start condition. The factory hoses offered by BMW are plastic and will yield the same results of becoming brittle and damaged over time.

We have created a full motorsport-style solution with our CSL Crankcase made from machined 6061 billet aluminum with AN-style fittings and nylon fiber braided lines. This is a fully serviceable replacement that will outlast every one of the OEM replacements. Our AN crankcase line can be used to replace the factory brittle hose to ensure your S54 is free from vacuum leaks and performing properly.

OEM CSL Vent Hose (11157833649) - Direct Replacement for cars with secondary shut-off valve. (11157834056)

Key benefits:

Lifetime replacement of the brittle OEM plastic crankcase breather hose
Fully Serviceable
Motorsport Aesthetic to compliment your CSL Intake Plenum
Design:

Fittings are made from billet 6061-T6 aluminum and finished in Type II black anodizing
Pre-anodized machined Turner branding
Nylon fiber braided lines
Fittings are a direct replacement for the plastic OEM fittings
Not for sale or use in the state of California on any pollution-controlled vehicle as per the California Air Resources Board.

Modern day emissions regulations require the use of a closed crankcase ventilation (PCV) system to recirculate combustion blow-by gases from the crankcase back in to the intake to be burned.  Unfortunately, these blow by gases contain water vapor (which is a byproduct of combustion) and pick up oil mist from and the windage cloud and cam lubrication system as they travel through the crank case.  Due to less than 100% effective air/oil separation in the stock PCV system, some oil mist and water vapor gets carried back to the intake tract and over time cause oil deposits in the intake manifold, intake ports, and on the back of intake valves.  All will eventually lead to poor performance and reduced fuel economy, and the presence of this oil mist in the intake charge may even increase the risk of engine-damaging detonation. 

With forced induction, track use, and/or extended high RPM usage, these symptoms increase as the factory PCV system is overwhelmed, and a catch can becomes a must for your E46 M3. This kit is a direct fit making this an easy reversal if desired as well as maintaining a clean appearance by utilizing the open "smuggler's compartment" on the passenger side of the engine bay.

ECS engineers developed a catch can that utilizes a strategically designed 4 chamber baffle plate system engineered to create multiple changes in the direction of airflow to cause oil droplets to fall out of suspension, maximizing the efficiency of the PCV air/oil separation.  A dipstick is integrated into the cap so you can monitor the oil level, and the can is easily serviced.  At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil.  The ECS Oil Catch Can is CNC machined from billet 6061-T6 aluminum and with a stealthy black anodized finish for lasting durability and appearance, and includes everything needed for an OEM-like fully reversible installation.  

The ECS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The ECS OCC also has a factory-like appearance. Having a kit designed specifically for your E46 M3 makes for a clean looking setup that any skill level mechanic can install. 

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles.

*Click here for installation instructions*

ECS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ 4 chamber design promotes excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Anodized black lightweight aluminum
+ Made in USA

This item fits the following BMWs
E46 M3 2001-2006

Upgrade your exhaust system with the Stainless Steel Oxygen Sensor (O2) Weld Bung (M18x1.5mm). This high-quality weld bung is made from stainless steel, ensuring durability and resistance to corrosion. It features M18x1.5mm threads, making it compatible with most oxygen sensors. Perfect for custom exhaust setups or replacing damaged bungs, this weld bung is a must-have for any automotive enthusiast.

• Made from high-quality stainless steel for durability and corrosion resistance
• M18x1.5mm threads ensure compatibility with most oxygen sensors
• Ideal for custom exhaust setups or replacing damaged bungs
• Essential for automotive enthusiasts looking to upgrade their exhaust system