BMW Drivetrain Parts for BMW 3 Series E46 (1999-2005)

When it comes to the torque found on axle nuts you're already looking at using a breaker bar or impact gun not to mention the corrosion collected over the years. The safest approach is using impact socket, since they are built with the strength needed to avoid breaking under pressure.

Features:

• Heavy duty ½ inch-drive sockets and drivers have extra thick alloy steel walls, and take a beating that would destroy normal sockets
•  Durable black oxide coating wipes clean easily and resists rust
• Contains three 12-point sockets for a sure grip on the most common sized axle nuts, plus three hex drives for removing common hex-head plugs and fasteners
• Conveniently packaged in a blow molded case, this set will please the most demanding professional technician or discriminating prosumer

Kit includes:

• 30mm, 32mm, and 36mm - 12-point axle nut sockets - ½" drive

• 14mm, 17mm, and 19mm hex head drive axle shoulder bolt sockets - ½" drive

Commonly used when replacing axle shaft boots.

Features:

• Crimp and flatten design
• Produces a clean factory style crimp
• Limited Lifetime Warranty

Upgrade the holding power of your clutch with the Clutch Masters FX250 clutch kit.

FX250 (Stage II)

• Extra long life street system
• Holding capacity 70% over stock
• Heavy-Duty reinforced pressure plate
• Rigid organic/fiber tough disc

All Clutch Masters clutch kits come complete with:

• Pressure Plate
• Clutch Disc
• Throw-out Bearing
• Pilot Bearing or Bushing
• Alignment Tool

Fitment in following BMWs:
E46 BMW - Non-M submodels, For vehicles with 5 speed transmissions only. Fits 325i/Ci models with a production date up to 03/2003.
Z3 BMW - Non-M submodels,  ACT recommends upgrading to the E36 M3 Slave cylinder for best clutch operation.

A sloppy shifter is one of the common complaints of older BMWs. In addition to the shifter linkage the transmission mounts contribute to rough and clunky shifting. BMW transmission mounts are rubber and get softer over time. This allows the transmission to dance around which changes the geometry of the shift linkage and could make it harder to shift. These urethane transmission bushings are stiffer than the stock rubber mounts and won't let the transmission shift around as much. The round design also has more surface area than the stock mounts which helps spread the load. Because the urethane is stiffer, expect more vibration to make its way into the shift lever area. Engine motor mounts should also be considered as a cause for driveline vibration, transmission movement, and poor shifting. Consider replacing your motor mounts at the same time as your tranny mounts.

Price is for the pair of transmission mounts with hardware.

This item fits the following BMWs: 
1989-1995  E34 BMW  525i 530i 535i 540i M5 
1992-1998  E36 BMW  318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 
1997-2003  E39 BMW  525i 528i 530i 540i M5 
1999-2005  E46 BMW  323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 
2008-2012  E82 BMW  128i 135i 1M Coupe 
2006-2011  E90 BMW  325i 328i 330i 335d 335i - Sedan 
2006-2012  E91 BMW  328i - Wagon 
2007-2013  E92 BMW  328i 335i 335is - Coupe 
2007-2013  E93 BMW  328i 335i - Convertible 
1997-2002  Z3 BMW  Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 

Your rear differential is indirectly connected to your right foot through the engine and driveline, and connected to the seat of your pants through the chassis. Soft factory rubber differential bushings absorb vibrations between chassis and differential, providing comfort and softness in both of these connections.

Enter ECS Tuning's In-House Engineered Performance Polyurethane Differential Bushings. By eliminating the deflection factory rubber bushings permit, the connection between your right foot (and your seat) to the wheels is improved. Removal of this slop allows for crisper power transfer from differential to wheels, which means better throttle control while carving a canyon road, drag racing, sliding the rear end out, or just driving to work. This is achieved without the harshness or vibration associated with delrin or solid differential mounts.

Featuring a tough 88A durometer polyurethane and Black anodized 6061-T6 aluminum Sleeve, our Performance Polyurethane Differential Bushings are more resistant to chemicals, ozone degradation, road salt, and general wear and tear than factory rubber bushings, resulting in a longer service life.

A sloppy shifter can make your driving experience miserable. Luckily these Genuine BMW shifter rebuild kits are available to restore the crisp feel of a brand new shifter. This kit includes all of the Genuine BMW components that normally wear down and cause issues such as the bushings, clips, and dowel pin.

See all of the included components below!

Upgrade the shifting experience of your BMW E36 325xi with the BMW E36 325xi Teflon Shifter Bushing Kit. This high-quality bushing kit features Teflon construction, providing smoother and more precise shifts compared to stock rubber bushings. Engineered specifically for BMW E36 325xi models, this kit offers improved durability and longevity, ensuring long-lasting performance. Enhance the driving experience of your BMW E36 325xi with this premium shifter bushing kit.

• Teflon construction for smoother and more precise shifts
• Improved durability and longevity compared to stock rubber bushings
• Engineered specifically for BMW E36 325xi models
• Enhances driving experience with smoother shifting

Performance clutch installation kit includes everything you need for a stage one clutch upgrade. Dampened Disc version. 

• FX300 (Stage 3)

• High performance street system

• Holding capacity 70% over stock

• Heavy-Duty reinforced pressure plate

• Hi-Leverage™ pressure ring design

• Sprung hub/cushioned disc

• Steel-backed Sprung Hub Segmented Kevlar Disc friction material

Fitment in following BMWs:This item fits the following BMWs: 
2003-2005 E46 BMW 330i 330ci  only for 6-speed manual transmission