BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

After the introduction of the M52TU/M54 engines, BMW observed an uptick in CCV-related issues, especially in cold regions. Vehicles operating in extremely low temperatures often encountered a blockage in the CCV dipstick hose, leading to elevated crankcase pressure and visible blue smoke from the exhaust. To address this issue, BMW introduced cold climate-specific hoses with foam insulation, preventing condensation and facilitating quicker oil warm-up. This kit incorporates top-notch reproduction cold climate hoses to ensure optimal CCV performance across all weather conditions.

The crankcase ventilation valve, known as the oil separator, PCV, CCV, or crankcase pressure regulator valve, plays a vital role in redirecting oil from your vehicle's intake system back into the engine oil pan. This system comprises numerous plastic and rubber hoses, prone to damage due to prolonged exposure to chemicals and heat.

Designed to tackle or prevent impending CCV system failures, this kit includes four foam-insulated hoses made from durable plastic capable of withstanding heat fluctuations and chemical exposure. Additionally, a new ventilation valve is included for a comprehensive and long-lasting repair solution.

Signs indicating the need for crankcase ventilation system replacement include:

Whistling sounds from the intake manifold, caused by crankcase pressure venting through holes in the CCV hoses. Blue smoke emitting from the tailpipe, indicating oil consumption. Excessive oil usage. Milky or yellowish buildup under the oil cap, suggesting condensation due to ventilation valve malfunction. If you're experiencing misfires, lean fuel codes, decreased fuel efficiency, or noticeable oil consumption, it's advisable to overhaul your crankcase ventilation system. Opt for this reliable system from Febi-Bilstein for a repair that meets factory standards and ensures consistent performance.

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top-tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• 7 times the flow of comparable paper oil filters
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• No more cutting apart messy paper filters for trapped debris inspection
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This product fits the following BMWs:
1995 - 1999 E36 M3
2001 - 2006 E46 M3
1998 - 2002 E36/8 Z3 M Coupe
1998 - 2002 E36/7 Z3 M Roadster
2006 - 2008 E86 Z4 M Coupe
2006 - 2008 E85 Z4 M Roadster