BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Enhance your BMW's performance with the upgraded BAV Ignition Coil, designed to boost firepower and optimize engine efficiency. These coils boast modified core windings for a faster, more efficient burn, resulting in increased torque at lower RPMs and heightened horsepower in the upper range. While improvements depend on your engine's condition, these coils ensure noticeable enhancements in performance and potential fuel economy benefits.

Product Benefits:

Improved engine firepower and efficiency
Increased torque at lower RPMs
Enhanced horsepower in higher ranges
Potential improvement in fuel economy
Set of six for complete BMW Cooper replacement

For BMW M54 applications, coil styles vary between M or N depending on the vehicle's production date. Models produced up to September 2002 require the M series style coil, while those manufactured after September 2002 use N series style coils. It's crucial to visually compare and verify the correct coil needed for your vehicle before making a purchase.

Benefits:

• Specific coil styles for different BMW M54 application dates
• Helps ensure the right replacement part for your vehicle's coil
• Visual verification recommended prior to purchase for compatibility

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

Fits the following BMWs:
2000-2006 E46 BMW 323/325/328/330

Rally Road Productions, Inc. is a team supported by a group of people with great abilities in their area of expertise. From the "web guy" and driving instructor friends, to owners of various machine shops, they have surrounded ourselves with people that can be trusted to create and manufacture quality products. This is the key to ensuring everything that they sell will perform as it was intended. The goal is to increase customer satisfaction and make the customization or performance enhancement of your vehicle a more enjoyable venture.

This oil cooler system is race tested and proven to outflow the euro M3 oil filter housing. Additionally, this particular system uses a sealing mechanism to direct the oil flow through the cooler lines and then through the oil filter.  Other cooler caps do not provide this seal and therefore the external oil coolers and lines act as a "balloon".  The lines and cooler are pressurized, but oil does not flow through them.  Flowing oil means it is being cooled and not just acting as an external reservoir.

Flow testing reveals that the oil cooler cap will outflow the Euro M3 Oil Filter Housing by more than 80% at the same, pressure, RPM, and oil temperature. In the upper RPM range, there is nearly a 100% improvement in flow from the RallyRoad oil cooler cap when compared to the Euro M3 oil filter housing.  This is a massive improvement over OE and is a worthwhile upgrade, especially in engines that see severe duty.

Features:

• -8AN o-ring ports to provide a leak free fitting without the use of Teflon tape or sealant used by other oil cooler caps.
• Viton o-rings are used throughout to maintain function and sealing in a high-temperature oil environment.
• Use of the stock filter cap bolt to reduce cost and simplify installation.
• An internal sealing mechanism to direct oil flow through the oil cooler and through the filter.
• 1/8" NPT side port for external oil pressure gauge.

Kit Includes:

• Oil filter cap with fittings
• Oil filter sealing ring
• BMW MANN Oil Filter and gasket

This part fits the following BMWs
1992-1999 E36 323i 325i 325is 328i 328is

Still looking for more power after bolt-ons? High performance camshafts from Schrick are the way to go. These cams are a direct replacement for the stock cams and give a solid 15+ horsepower boost at the top end and great midrange torque increases too! More gains can be expected with intake and header upgrades and custom software tuning. A slightly lumpy idle is expected at cold start but will be smooth once at operating temperature. This set is just a great all-around cam upgrade for the S54!

These Schrick cams were initially developed for the M3 CSL but they also work great on the US and other non-CSL S54 engines as well. With more duration they are a great match to high flow headers, no cats, or CSL intake manifold upgrades. These are the new "cast" cams from Schrick which require new rocker arms (Schrick recommended or BMW part #11337833259). Professional installation is a must due to the intricacies with the double VAN0S.

Schrick Technical Information / Specs

This item fits the following BMWs:

• 2001-2006 E46 BMW M3
• 2001-2002 Z3 BMW M Roadster M Coupe
• 2006-2008 E85 BMW Z4 M Roadster M Coupe

SEE T#338745 BMW S54 3.2L Schrick Camshaft Set 280/272 12.5mm Lift is the perfect performance upgrade for enthusiasts seeking to enhance their engine's capabilities. With over 40 years of experience, Schrick is dedicated to producing high-quality camshafts that deliver exceptional power and reliability. Designed for both street and track applications, these camshafts offer an impressive balance of performance and drivability. The intake cam features a duration of 280, while the exhaust cam has a duration of 272, with a valve lift of 12.5mm. These new "cast" cams from Schrick closely resemble the stock E46 M3 CSL cams, ensuring a smooth idle and a significant increase in horsepower throughout the RPM range. With a peak gain of 15 horsepower and no loss in low-end torque, these camshafts are a top choice for BMW enthusiasts.

Key Benefits:

• Enhanced Power: Delivers a peak gain of 15 horsepower.
• Smooth Idle: Maintains a factory-like idle quality for everyday driving.
• Linear Power Increase: Provides a steady increase in horsepower from midrange to redline.
• Compatibility: Designed to fit the BMW S54 engine with new rocker arms required.
• High-Quality Construction: Crafted from top materials for strength and durability.