BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Includes connector housing with terminals and seals. Commonly used for the engine oil level sensor.

ECS Tuning replacement harness connectors include all necessary pins and wire seals for a complete harness repair. Whether you have a broken harness connector or need a complete wiring repair, we have the components you need.

Each connector includes an additional terminal in case one becomes lost or damaged during installation.

*OEM cross reference PN# 12521433915 - Commonly used for the engine oil level sensor.

Please reference the original part number from the existing connector to confirm fitment, before ordering.

Suggested tools:

Suggested crimping pliers: T#387193
Wire De-pin tools:
12pc De-Pin Tool Set - T#386379
23pc De-Pin Tool Set - T#641943

Fix oil leaks on your BMW's passenger side engine with Turner Motorsport's CPV O-ring replacement. The O-ring failure in the CPV typically leads to slow oil leaks, and now you can address this issue at a fraction of the cost by replacing the O-ring instead of the entire CPV. Unlike the OEM Buna rubber, the new Viton Fluoroelastomer used in this O-ring is resistant to higher temperatures, ensuring prolonged life without leaks.

• Cost-effective solution for oil leaks on the passenger side of the engine
• Replaces the CPV O-ring without replacing the entire CPV
• Viton Fluoroelastomer resistant to higher temperatures
• Prolonged life without leaks
• Addresses O-ring failure due to heat cycling and oil exposure

If you have a faulty fuel pump relay, fuel will not be pumped to the engine and your engine may not start. Replace your relay with this high quality Bosch replacement to restore fuel pump operation.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This 4 prong relay fits many BMW's and fulfulls a variety of functions. Please check your relay pins configuration to ensure the proper fitment. Fits BMW 2002, e30 e36 e46 e28 e34 e39 e24 e23 e32 e38 e31 z3

This item fits the following BMWs:
1970-1976 2002 BMW 1600 2002 2002tii
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
1997-2003 E39 BMW 525i 528i 530i 540i M5
1982-1989 E24 BMW 633csi 635csi M6
1981-1987 E23 BMW 733i 735i
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M coupe M Roadster

This is an OEM INA tensioner pulley, also known as the adjusting pulley and lower pulley. This pulley is mounted on the belt tensioner near the center of the belt assembly. The upper and lower pulleys are known to be the primary sources for 'belt squealing'. This pulley is also encased in rubber which will crack over time. If left without service the rubber could fail completely, chucking the belt and leaving you stranded. Replacement is a very simple procedure and can be done anytime the fan is off the engine (belt replacement, water pump service, alternator replacement, etc).

This pulley is mounted along with the hydraulic belt tensioner but can be replaced on its own. It is used for the main drive belt on the M50-M54 family engines (M50, M50TU, M52, S52, M52TU, M54, M56, and S54 engines). This is the same belt that covers the water pump/alternator/power steering systems. Replacement is a very easy procedure (requires fan removal) and will have your engine purring in no time. Belt replacement is strongly recommended at the same time. If you have a mechanical belt tensioner, the pulley can only be replaced with a new tensioner.

OEM Schaeffler (INA, LuK, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

If you need the hydraulic belt tensioner, click here.

This item is 70mm Diameter. Please check the diameter before ordering.

This tensioner pulley fits the following BMWs:
1991-1995 E34 525i (M50 engine)
1992-1999 E36 325i, 325is, 328i, 328is, 323is
1995-1999 E36 M3 (M3 3.0 & M3 3.2 liter)
1997-2003 E39 525i, 528i, 530i - Only for Hydraulic Tensioner
1999-2000 E46 323i, 323Ci, 328i, 328Ci - Only for Hydraulic Tensioner
2001-2005 E46 325i, 325Ci, 325xi, 330i, 330Ci, 330xi - Only for Hydraulic Tensioner
2001-2006 E46 M3 coupe & convertible - Only for Hydraulic Tensioner
2000-2006 X5 3.0 liter (E53 chassis)
2004 E60 525i, 530i (M54 engine)
1997-2002 Z3 & MZ3 2.5, 2.8, 3.0, M Roadster, M Coupe
2003-2009 Z4 M Coupe and Roadster

Upgrade your Mini Cooper's hose clamping mechanism with the 3/8" (9mm) Band Hose Clamp from ECS. Designed for precision and durability, this clamp ensures a secure fit for hoses, preventing leaks and ensuring optimal performance. Crafted to meet high-quality standards, it provides reliable sealing and resilience against varying temperatures and pressures. Easy to install and engineered for long-term use, this hose clamp is an essential addition to maintain your Mini Cooper's functionality.

• Precision-engineered for Mini Cooper hoses
• Ensures a secure and leak-free fit
• Resilient against temperature and pressure variations
• Easy to install and durable for long-term use