BMW Engine Parts for BMW 3 Series E46 (1999-2005)

The main reason all of the VANOS units will eventually fail is because the material used for the sealing rings from the factory is not designed for that type of environment. When this happens the only option that BMW leaves you with is buying a new and expensive VANOS unit with the same sealing rings that failed in your original unit.

The VANOS system found in BMW engines is a great feature (when it’s working properly), keeping your power curve smooth and responsive especially in lower to mid RPM range. What usually goes unnoticed is the gradual loss of power within this range as the vehicle's age due to slowly failing seals within the VANOS unit. The way the VANOS system works is based off of oil pressure triggered by a solenoid that allows for a small range of timing degree adjustment, this is where the power curve is affected. When the seals begin to fail (all of them do) there is less pressure to advance the timing reducing the power in that low to mid range. Because this happens slowly it's very hard to notice a difference until you refresh your VANOS unit, then you easily realize the response you've been missing.

There are a number of symptoms that will plague your car as a result of these failing seals such as erratic idle, engine hesitation, stalling, and increased fuel consumption to name a few. If you've been chasing down any of these symptoms with no fix then this could be your issue.

While you're replacing the seals in your VANOS unit it a good time to install anti-rattle spacers to tighten up the gaps in your stock assembly and get rid of that noisy VANOS clatter.

Seals & O-rings:

The seals  were the main focus of this project since the OE units are built with Buna-N rubber o-rings instead of the ECS supplied Viton rubber o-rings. The Buna-N material quickly hardens from the heat and chemical exposure within the engine, where the Viton is significantly more resistant to these chemicals. This knowledge was also used when it came to the commonly failed o-rings found on the VANOS seal plate, replaced at the solenoid.

Rattle Repair:

When it comes to the VANOS rattle this is commonly described as "marbles in a can", and can be heard throughout the different RPM ranges depending on the engine. These upgraded rings and washers are precision ground from hardened steel to resist wear and deformation keeping your VANOS rattle free. The rattle repair tools are designed specifically for this VANOS anti-rattle repair, design from hardened steel to stand up to the job. Designed to perfectly follow the splines of the shaft for a tight grip when applying the necessary torque to disassemble & reassemble the VANOS transfer gear. The keyed socket was designed with the intent to use a "common" wrench so this can be completed at home in your garage.    

When Servicing your VANOS unit we recommend getting everything you need to replace on the way to service which includes an oil change and valve cover gasket set. Fresh oil and gaskets is the best way to start off a fresh rebuild of any kind giving you the maximum performance of your freshly serviced components.

Don't forget to check out our rebuild PDF to make sure you have everything to get the job done and eliminate the rebuild guess work.

This item fits the following BMWs: 
2000-2001 E46 3 Series M3 M3 Convertible 2000-2006 
2001-2002 Z3 Roadster / Coupe Z3 M Roadster Z3 M Coupe w S54 Engine 
2006-2008 E86 E86 Z4 Z4 M Roadster Z4 M Coupe

Bremi Camshaft Position Sensor - Intake is an essential component for optimizing your BMW’s engine timing and performance. Manufactured by Bremi and available through Turner Motorsport, this high-quality intake camshaft position sensor precisely monitors the camshaft’s rotation and communicates critical data to the engine control unit. By ensuring accurate timing for the intake valves, this sensor helps maintain optimal fuel efficiency, smooth idling, and reduces emissions. Replacing a faulty camshaft position sensor can prevent common engine issues such as misfires, stalling, or rough idling.

The Bremi Camshaft Position Sensor - Intake meets OEM specifications, providing a reliable, durable solution that’s designed to withstand high temperatures and vibration for long-lasting performance.

Benefits:

Improves Engine Timing: Provides precise timing data for smooth, responsive engine performance Enhances Fuel Efficiency: Optimizes fuel use, saving on fuel costs and reducing environmental impact Reduces Emissions: Helps maintain cleaner combustion and lowers vehicle emissions Prevents Engine Issues: Minimizes risk of misfires, rough idling, and stalling, prolonging engine life Easy to Install: Direct fit for BMW models, making replacement quick and hassle-free Bremi Camshaft Position Sensor - Intake is the perfect choice to maintain your BMW’s high performance and reliability.

The Borescope Inspection Camera offers 1920P HD resolution, a flexible 7.9mm probe, and a 16.4ft semi-rigid cable, making it ideal for inspecting hard-to-reach areas. Easily connect to IOS and Android devices, and use the IP67 waterproof probe for various applications, including automotive, plumbing, and home inspections.

Key Features:

• 1920P HD Resolution: Capture clear images and high-quality video at 1920x1440 resolution.
• Easy Connection: Connect quickly to IOS 9.0+ and Android 7+ devices via the 'SUP-ANESOK' app.
• Semi-Rigid Cable: 16.4ft cable offers a mix of flexibility and rigidity for precise inspections.
• Waterproof Probe: IP67-rated, capable of operating underwater up to 3.28 feet for 1 hour.
• Wide Applications: Suitable for automotive, plumbing, and home inspections, with adjustable brightness for low-light environments.

Includes:

• Borescope Camera
• Android Adapter
• Lightning Port Adapter
• USB Type-C Connector
• 16.4 ft. Semi-Rigid Cable
• Magnet
• Hook
• Mirror
• Protective Cap
• Manual

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.

Bad oxygen sensors can cause check engine lights and poor fuel mileage. Replace your faulty sensor with this high quality Bosch sensor to turn off your check engine light and restore fuel mileage.

This is the pre-cat oxygen sensor for cylinders 1-3 for BMW E46 M3. Bosch # 13 949. This is a OEM replacement part for BMW part # 11781743994.

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 convertible
2001-2002 Z3 BMW M Roadster M Coupe

BMW M42 M50 M52 M54 6mm Single Groove Valve Keeper is a precision-engineered component essential for securing valves in BMW engines. Turner Motorsport offers this high-quality valve keeper, designed to fit specific Supertech valves for enhanced performance and reliability.

• Precision Fit: Designed specifically for BMW M42, M50, M52, and M54 engines, ensuring a perfect fit with 6.0mm single groove valves.
• High-Quality Construction: Made from durable materials to withstand high-pressure conditions and provide long-lasting performance.
• Enhanced Valve Security: Two keepers are required per valve to securely hold the valve in place, preventing movement and ensuring consistent engine performance.
• Compatibility: Ideal for use with certain Supertech valves, providing a reliable solution for engine builds and upgrades.
• Easy Installation: Simple to install with standard tools, offering a hassle-free upgrade or replacement option.

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!