BMW Engine Parts for BMW 3 Series E46 (1999-2005)

Rogue Engineering has developed a power pulley kit that reduces the drag on specific pulleys while allowing others to remain at their same efficiency. This allows for perfect operation in daily driven vehicles without a hiccup or stutter. However, when the demand for power is requested, the power pulley kit allows for the freed power to become apparent.  The term "power" pulley is a bit of a misnomer. Underdrive pulleys actually free up power by reducing the drag caused by the accessories.  These pulleys are based off a calculated percentage from factory dimensions, so that particular component speeds are safely reduced without affecting their true purpose.

Rogue Engineering Power Pullies are CNC machined from 6061-T6, heat treated aluminum and specially coated with a MIL-A-8625 Type III hard coat anodize finish. This kind of anodizing is not to be confused with a Type II cosmetic anodize finish (typical colors such as red, blue, silver, green, etc.). The hard coat anodize finish actually builds a small surface layer on top of the aluminum, preventing wear.

This part fits the following BMW engines:
S54

This part fits the following chassis:
E46, Z3, Z4

This solenoid works with the VANOS engine timing system to improve horsepower and torque throughout the RPM range.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Solenoid Valve (Solv) -
This item fits the following BMW Chassis:
E39,E46,E53 X5,E83 X3,E85

Fits BMW Engines including:
M52,M54,M56

Head Gasket for M52TU and M54 Double VAN0S engines. Fits E46 325, 328, and 330.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

If you're the proud owner of an S54-equipped BMW, chances are you're passionate about enhancing your vehicle's performance and longevity. One crucial upgrade that can significantly improve your driving experience is Turner Motorsport's WPC Rod Bearing Replacement Kit, coupled with ARP Rod Bolts for increased durability.

Enhanced Durability: The WPC Performance Rod Bearing Replacement Kit is designed with superior materials and manufacturing processes. WPC treatment reinforces the surface of the bearings, making them highly resistant to wear, which is essential for high-revving engines like the S54. This durability ensures your engine will stand the test of time, even under strenuous driving conditions. Improved Performance: By reducing friction and wear, WPC-treated rod bearings allow for smoother and more efficient engine operation. This increases power and responsiveness, providing a more exhilarating driving experience. Whether tearing up the track or enjoying a spirited weekend drive, you'll notice a difference in your vehicle's performance. Precision Engineering: Crafted from premium quality materials, these bolts and bearings offer exceptional tensile strength and structural integrity. This guarantees that your connecting rods will stay securely in place, even during high-stress situations. Your engine's components will work in perfect harmony, minimizing the risk of catastrophic engine failure. Preventative Maintenance: The S54 is notorious for rod bearing failure, often necessitating complete short block replacement. Choosing to proactively replace your rod bearings with our WPC offering ensures smooth operation and eliminates potential engine failure. Included in the kit:

12 - Turner Motorsport "Race Series" WPC-Treated Bearing Shells 4 - Self-Locking Collar Nut - Priced Each 1 - Oil Pan Gasket - Elring 1 - Oil Pan Center Cover Gasket 1 - Oil Filter Kit 1 - Oil Drain Plug 1 - Dipstick O-ring 1 - ARP Connecting Rod Bolt Kit (M10x1.25 - for S54B32 produced after 02/2003) 6 - Castrol Edge Euro Car Engine Oil (10w-60) Quart 1 - Redline Assembly Lube - 4 oz

VAC's S54 Vanos Hub is designed as a direct replacement for the fragile BMW OE Vanos Hub which typically fails due to a broken drive pin. The VAC Hub has an Upgraded Drive Pin design, which is larger in diameter, as well as more material on the outside wall of the pin. In addition, the hub is made from 4340HT Billet Bar and heat treated to the same BMW OE Rockwell Hardness spec. The upgraded design is not only significantly stronger, but the larger diameter Drive Pins also minimize the huge clearance (approximately 1mm) that was in the original design by BMW and reduces the clearance to 0.2mm. This is critical in helping greatly reduce or eliminate the VANOS noise.

Also, this upgraded design eliminates the need for modifying the Pump Ring or having to buy a replacement, which further saves you money!!!

BMS Billet Spark Plug Gapper Tool - 14mm is an essential tool for achieving accurate and consistent spark plug gapping, ideal for automotive enthusiasts and professional mechanics alike. This precision tool helps maintain optimal plug performance by providing reliable, consistent gaps. Available in both 14mm and 12mm plug thread sizes, this tool is proudly made in the USA to deliver durability and precision.

• Precisely gaps spark plugs for enhanced engine performance and efficiency
• Speeds up the gapping process while ensuring accuracy and uniformity
• Available in two sizes (14mm and 12mm) for a wider range of compatibility
• Optional specialty feeler gauge included with 4 blades in thicknesses of .018, .020, .022, and .024
• Made in the USA for premium quality and durability

Crafted from high-grade domestic USA 6061-T6 Billet Aluminum, these pulleys are a testament to precision engineering. Rigorously tested through extensive hours of racing and street use, they've proven their reliability and performance excellence.

Each pulley is meticulously zero-balanced and thoroughly inspected to ensure zero-runout, guaranteeing optimal performance without compromising on reliability, noise, or vibration.

This comprehensive kit comprises a precision power steering pulley, water pump pulley, and an OE Contitech Brand drive belt. Experience a notable boost of 8hp and 7 ft/lbs. of torque to the wheels, making it ideal for stock vehicles, track cars, and even those with upgraded audio systems seeking consistent voltage output from their alternators.