BMW Brakes & Brake Parts for BMW 1 Series E82 (2008-2013)

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a superior zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Turner has developed a proprietary zinc-nickel coating finish with nearly twice the salt-spray corrosion resistance of a standard plating. Turner SS brake lines also feature new low profile connecting hardware, for a cleaner mounted look. Get the brake lines that will continue to look as good as they feel!

-Fully compliant with DOT Standards (MVSS-1006) -Lines burst-tested to 3000psi (maximum tested pressure from a BMW braking system is 1200psi) -Zinc-Nickel coating for maximum corrosion resistance -Low profile connectors for clean and recessed look

Everything you need to upgrade your front and rear brakes in an afternoon in one simple kit!

By providing it all for you in a single click, this kit has made it easier to get the quality upgrade components you need when beginning a brake service. This performance brake service kit includes rotors, pads, sensors, assembly grease, and set screws to make your brake upgrade easy.

Includes the following parts:

Front ECS 2-piece drilled and slotted rotors Rear ECS V5 drilled and slotted rotors Front and rear ECS EP24 "Enthusiast Performance" Brake Pads Pad wear sensors ECS stainless steel rotor set screws Brake lubricant compound packet Includes ECS Stainless Rotor Set Screws to eliminate rusty factory fasteners

This caliper bushing kit will eliminate flex caused by weak rubber caliper bushings. As the brake pedal is pressed the caliper grabs the rotor and twists on its mounting bushings. The rubber bushings allow the caliper to deflect and twist which affects pedal feel and results in uneven pad wear. These solid brass bushings will not twist or deflect so your calipers can squeeze the pads evenly on both sides of the rotor (sort of like what multi-piston big brakes do). This will give you much longer pad life and a more consistent pedal feel. This is the most complete kit we have ever sold with stainless steel caliper slide bolts, o-rings, and new dust boots. Unlike other kits, these bushings are pressed into the caliper and will not shift or slide on their own.

Installation is straightforward: remove the old rubber bushings and press in the new brass bushings (we recommend special tool 003326ECS03). High temp caliper grease or anti-seize is required. The new bushings include an inner o-ring that helps trap grease on the slide bolt, reducing friction and wear.

***Click here for installation instructions*** 

***Click here for the installation tool***

For most models with floating calipers. Fits the rear of E90/2 and E60, but for the front you'll need the kit found here. Does not fit E30 models with Girling calipers, but is compatible with Ate calipers. 

Installs bushings straight and true with minimal effort. Includes tools for both iron and aluminum calipers. Purchase only one tool set for your entire caliper guide bushing upgrade - tools are not one time use.

***Click here for installation instructions*** 

BRAKE BLEEDER:

We know bleeding brake alone is not only no fun, but much more complicated than it needs to be. Having a pressure bleeder give you the ability to keep the pressure on the brake system while you go under and crack open the bleeder screws to relieve the air pockets.

Features:

• Holds a full 3-Liters (3.17 qts) of brake fluid
• Easy to read 0-30 lbs pressure gauge built into the tank top
• Pressure relief valve for safe release of pressure
• 40" hose with detachable swivel fitting

Note:

• Do not exceed 20 PSI
• LIFETIME REPLACEMENT

Includes:

• 3 Liter (3.17 qts) storage tank
• Pressure cap with 0-30 lb gauge and pressure relief valve
• 40" hose
• Dual preventative fittings on the hose, featuring a chrome quick coupler on one end to snap onto the master cylinder cap and a detachable swivel fitting on the other end

Note:

• Recommend working at 10 PSI
• Dimensions for cap seal: 12x21x4 mm
• LIFETIME REPLACEMENT

CATCH BOTTLE:

Keep your fluid's off the floor and into our catch bottle.  The bottle has fluid level markings from 0.2L to 0.7 liter. This feature allows you to measure how much fluid you have sent thru the system.  Our bleeder bottle features an expandable/collapsible top portion for easier storage. Gasket in cap prevents leakage. Tubing is extra long at 24" from cap to nipple. Flexible hose can be pushed down into bottle for storage when done. Bottle now features a handy hanger bracket to hang bottle from bottom of car.

CALIPER HOOK SET:

Tired of messing with bent coat hangers or bungee cords to hang your calipers up and out of the way when performing brake maintenance? These hooks make working on your brakes easier by letting you hang your calipers with ease, no more fighting with the bungee cords or zip ties to hold the caliper just right or having to make your own "custom" hooks with wire.

• Holds brake calipers out of the way while working on brakes
• Also use to hang other automotive parts and tools while working on your vehicle.
• Stronger than zip ties or wire.
• Save the brake hose by not hanging caliper by hose.
• Made of  thick steel for strength and durability. length is 8"

BILLET ALUMINUM CAP:

This aluminum cap with 90 degree swivel will work with our T#363245 Euro bleeder or our T#366970 3-Liter Multi-functional Fluid Pump Kit.

Features an all aluminum 45mm cap with quick coupler nipple.

BLEEDER WRENCH:

Finally, a bleeder wrench with just the right angle to open the bleeder screw without having to spend all that time removing each wheel from your car.

WARNING: This product contains chemicals known to the state of California to cause cancer, birth defects, and/or reproductive harm. See above warning label as well as http://www.p65warnings.ca.gov for further information on Proposition 65 warnings.