BMW Engine Parts for BMW 1 Series E82 (2008-2013)

Ignition coils are key to the efficiency and performance of your BMW. With a faulty coil the spark plug is not burning the air/fuel mixture properly and that can lead to problems anywhere in the engine and exhaust (including catalytic converters and O2 sensors). Problems with one or more coils will cause a fault code but not always a check engine light. A misfire code may be related to an ignition coil but could be from other things as well. Sometimes a visual inspection of a coil and coil boot will give an indication of a failure. You can also move coils around to different cylinder banks to see if the misfire code follows a suspect coil. We suggest always having one or two coils on hand to keep as spares.

This is the current replacement for some BMW 6 and 8-cylinder engines built in the late 2000s and after. BMW has made numerous changes to ignition coil part numbers in recent years but has approved this part number to work in the vehicles listed below. It's listed as a replacement coil for N20, N55, and S55 engines. In March 2015 BMW approved it for N51/N52 engines. This part number replaces the previous BMW part number 12137594937 for the cars listed below.

Sold per coil. Includes boot and connector.

If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On E9X BMWs, the engine ground strap is a thin, non-insulated cable that spans from the left engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.

To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your E9X BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.

Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.

FEATURES

Direct-fit replacement and upgrade for RWD E82/E88, E84, and E9X applications Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12427549393, 12427795404, and 12427790559.

Elevate your custom installation with the ECS -10AN O-Ring Boss fitting, a crucial component that connects your ECS Tuning Catch Can to a 3/4" ID hose. This fitting simplifies your plumbing setup, ensuring a seamless solution.

Featuring a pre-installed Viton O-ring, this fitting is engineered for excellence, providing a leak-proof seal that resists the effects of oil and fuel exposure, guaranteeing long-term durability.

The 3/4" nipple is thoughtfully designed with barbs to secure hose position effectively, minimizing the risk of hose disconnection. Keep in mind that clamps and hoses are available for separate purchase. These fittings are sold individually, with most installations requiring a pair of them.

Ensure the correct voltage is being sent to/from the alternator, keep you electrical system safe from excessive voltage peaks that could cause damage to sensitive electronics and blow out fuses. Bosch's high quality unit will give you peace of mind knowing the electrical system will be safe and the voltage will remain steady. OEM replacement for BMW part # 12317561939

Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

BMW N52 3.0L Spark Plug - Set Of 6 (LZFR6AP11GS) ensures optimal engine performance by providing reliable ignition and efficient combustion. These high-quality spark plugs are essential for maintaining the performance of BMW N52 engines, as poor spark can lead to reduced fuel economy, lower horsepower, and the dreaded check engine light.

Replacing spark plugs every 60,000 miles is crucial to restoring and enhancing your vehicle's performance. With these spark plugs, drivers can expect improved acceleration, smoother idling, and better overall engine responsiveness.

• Direct replacement for BMW N52 3.0L engines, ensuring compatibility and optimal performance
• High-quality construction designed to withstand high temperatures and pressures
• Improved fuel economy and reduced emissions for a more eco-friendly drive
• Restores lost power and acceleration, enhancing the driving experience
• Recommended replacement interval of every 60,000 miles for peak performance

Port Injection Fuel Line For Top Mount Fuel Rail - N54 N55 is designed for seamless compatibility with most aftermarket intake manifolds featuring top mount port injection. It works with leading brands such as Black Market Parts, BKC, BMS, Sharp Custom, Doc Race, and more, ensuring a high-performance fuel delivery solution for BMW N54 and N55 engines.

Constructed with premium 6061 aluminum and anodized for 100% E85 compliance, this fuel line is engineered for durability and optimal fuel flow. The female quick connectors feature an air hose-style quick connect with dual seals (primary and secondary) to eliminate any risk of fuel leaks. Precision Raceworks utilizes Smooth Bore PTFE hose, a trusted component in high-end E85 applications worldwide.

This plug-and-play solution is fully compatible with both factory and aftermarket fuel lines, providing an easy, reliable way to supply fuel to the port injection system of your upgraded intake manifold.

• Seamless fit – Compatible with most aftermarket top mount port injection manifolds
• Durable construction – Machined from 6061 aluminum and anodized for E85 compatibility
• Leak-proof design – Dual-seal quick connectors for maximum fuel safety
• High-performance fuel delivery – Utilizes Smooth Bore PTFE hose for optimal flow
• Easy installation – Direct plug-and-play with factory and aftermarket fuel lines