Turner Motorsport for BMW 1 Series E82 (2008-2013)

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

*Still require a solid mount? Turner Motorsport solid engine and transmission mounts for N52/N54/N55 coming early July 2017.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

High Performance air filter, replacement filter for Turner Motorsport intakes, or great for your custom intake project. 

Filter Dimension 

• 178MM length 
• 127MM base
• 75MM inlet 

Track-tested and street-ready. the ULTIMATE cooling system upgrade for your N54 or N55!

Ditch your failure-prone plastic end tanks and increase cooling capacity by 25%, all without modifying your core support or accompanying shrouds. The CSFxTurner Performance Triple-Pass Radiator is the best cooling system upgrade for your N54/N55-equipped BMW!

The BMW 135i and 335i deliver serious performance straight from the factory, thanks to the twin-turbocharged N54 and single-turbo N55 engines. With strong midrange torque, high-revving capabilities, and proven tuning potential, these engines punch well above their weight. However, while the powertrain excels, the factory cooling system often falls short, especially under sustained boost or track conditions. Heat soak, rising coolant temps, and long-term thermal stress are common issues for enthusiasts pushing their N54 or N55 hard, making a performance radiator an essential upgrade for reliability and consistency.

Recognizing the critical need for increased cooling capacity, the team at Turner Motorsport partnered with CSF Race, world leaders in high-performance cooling systems with over 50 years of experience. The result is an Upgraded Performance Radiator: a high-performance, motorsport-grade upgrade engineered to keep your N54/N55 cooler and on the track for longer.

Design:

CSF-Exclusive "B-Tube" Technology
Unlike conventional "O-tube" designs, CSF’s patented "B-tube" structure increases wall strength while creating a more efficient flow path. This alone accounts for a 15% increase in cooling capacity over an OE "O-tube" radiator!
Dual Core Design
2-Row 42mm Core (Dual Core) Featuring CSF's Exclusive B-Tube Technology
Two-Row Compact Structure
This radiator was designed with precise fitment in mind. While total tube count and size are increased, the overall radiator dimensions stay the same as OE, ensuring a drop-in fit with zero modifications required.
25% Increase in Cooling Capacity
All of the above design features translate to a massive 25% cooling increase over the stock radiator!
FEATURES & BENEFITS

Direct-fit upgrade, no modifications required!
Accepts all OEM attachments via CNC-machined "Quick-Connect" hose ends and accessory mounting provisions
TIG-welded aluminum construction provides increased durability
An all-aluminum drain plug replaces the weak OE plastic unit, ensuring seamless functionality for the life of the radiator
Increased cooling efficiency for high-performance and racing use
Aluminum drain plug
Designed and tested by Turner Motorsport in collaboration with CSF Race
Backed by the Turner Lifetime Replacement Program
Every unit features precision CNC-machined brackets and OE-style connections for a seamless, drop-in installation using factory or aftermarket hoses. Whether you're building a track weapon or a high-horsepower street car, this Turner x CSF radiator is the cooling solution your N54 or N55 needs to perform reliably under pressure. All backed by the Turner Lifetime Replacement Program.

When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system  baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.

Our catch can was also designed with the idea that the cans fill level can easily be checked with a top mounted dipstick and an optional use bottom drain hole. The drain system comes complete with a valve and hose to be mounted at a lower area of the vehicle so when you're doing an oil change you can drain the catch can.

Features:

• 6061-T6 billet machined body, anodized black for lasting protection and appearance
• Strategically positioned 4 chamber baffle system maximizes oil / air separation 
• Knurled and black anodized oil dipstick makes inspecting oil volume of reservoir clean and simple
• Sealed with a pre-installed viton O-Ring
• Includes 2.5mm allen key to remove baffle plates for cleaning
• Engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can
• Closed / recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation
• Optional use drain hole - drain kit included!
• Universal mounting kit

Unlock the full potential of your turbocharged N54 or N55 engine with the Turner Motorsport Stepped Intercooler. Whether you're running higher boost, track days, or just spirited street driving, this direct-fit upgrade is engineered to dramatically reduce intake air temperatures (IATs) and improve charge air flow for consistent, reliable performance.

Cooler air is denser air, and that means more oxygen per cycle for better combustion and more power. The factory intercooler quickly becomes a bottleneck under increased load or in warm conditions. Turner’s stepped intercooler solves that by offering an 80% increase in frontal surface area and cross-sectional flow, helping your BMW stay cooler and pull harder.

Constructed with high-quality cast aluminum end tanks and a bar-and-plate core, this intercooler delivers superior cooling efficiency and reduced pressure drop, even under sustained high-boost operation. The black powder-coated finish offers a clean, stealthy appearance, while the etched Turner logos add just the right touch of motorsport style.

Perfect for:
E82/E88 135i, E9X 335i/335xi, E84 X135i, E89 Z4 35i/35is

Key Features:

Direct-fit upgrade for E chassis N54 & N55 engines
Durable cast aluminum end tanks
High-efficiency bar-and-plate design
80% increase in frontal and cross-sectional area vs. stock
90% increase in charge air volume
Substantially lower IATs for improved power and reliability
Reduced and more consistent pressure drop
Lightweight design (under 20 lbs)
Dimensions: 520mm wide × 210mm tall × 130mm deep
Stealth black finish with Turner-etched logos
If you're looking to push your turbo BMW harder, the Turner Motorsport Stepped Intercooler is the cooling solution that keeps your engine running strong—pull after pull.

M3 upper and lower control arms are a known upgrade for non-M E82 and E9X chassis. But our Monoball Thurst Arms are even more of an upgrade over the stock M3 arms. This package bundles the Turner Monoball upper thrust arms with the stock M3 lower control arms. If there's one big fail point in the E82/E9X front suspension it's the thrust arms. The front inner thrust arm bushing is filled with dampening fluid that leaks over time. Once it's gone the bushing has the strength of a rubber band. Even though we sell two types of upgraded rubber bushings there was still room for improvement. For someone looking for superior performance and longevity these sealed monoball bushings are the best out there. 

The advantage of a monoball bearing is that it will not deflect under load. All of the rubber bushings, including the M3, move in all sorts of directions and that changes your alignment, especially when used with big brake kits or when driven hard. And when worn out, performance suffers. Our monoball sits in a CNC machined aluminum housing which has zero deflection. The monoball allows complete freedom of movement but only at the desired angles. What you get is superior steering precision, better handling from more consistent alignment, and almost infinite bushing life. And thanks to the inner liner and sealed rubber boots there's none of the extra noise or reduced service life of fully solid race bushings.

The lower M3 control arm bushings use a similar sealed monoball bushing instead of rubber. This package gives you monoball precision and performance with OE-quality components.

This item fits the following BMWs: 
2008-2012 E82 BMW 128i 135i 1M Coupe 
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan 
2006-2012 E91 BMW 328i - Wagon 
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe 
2007-2013 E93 BMW 328i 335i M3 - Convertible 
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is 

Set of 2 universal 2.5" inlet to 3.5" outlet exhaust tips.

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

Swivel feature for perfect alignment of the exhaust tips in the rear bumper
2.5" Inner Diameter
3.5" Outer Diameter
Brushed Aluminum Finish
Double Wall Construction
Angle Cut Style
Includes Stainless Steel Clamp

Rubber engine and transmission mounts for a street car and solid aluminum for the track, right? Well, it's not that straightforward anymore.

Stock rubber fluid-filled mounts are designed to be soft and comfortable, limiting the NVH (noise, vibration, and harshness) felt by the driver. The drawback inherent with a conventional design is driveline deflection, making it more difficult to put the power to the wheels, as well as making a money-shift or miss-shift more likely as they age. Solid mounts are exactly the opposite of this - they permit tons of NVH while offering zero deflection, making these a must have for track-driven vehicles looking to capitalize on every ounce of performance available. Enthusiasts looking to find the best of both worlds often look to polyurethane engine mounts - and many are disappointed with other designs on the market. Seeking a mount that offers a positive connection yet doesn't deform, fail, or rattle the fillings out of their mouths is frequently a lost cause.

Until now. 

We engineered these mounts with these very concerns in mind. We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration. Understanding that heat is a concern for the passenger side mount's close proximity to the exhaust, we utilize a PEEK thermal insulation plate to greatly reduce heat transfer to the polyurethane, making heat a non-issue for these mounts. 

We offer two durometers, with both densities offering similar "positive connection" feeling. 60A is slightly softer and offers more of a stock feel, while 80A delivers a little more engine "feel" while under acceleration. 

Product features and benefits:

• Crisper throttle response, positive shifter location, direct power transfer
• High quality polyurethane offered in both 60A & 80A durometers (rebuildable, too)
• Resistant to water, ozone, and chemicals, maintaining its resiliency and elasticity longer than conventional rubber.
• Precision machined billet 6061-T6 aluminum housing, black anodized for durability and corrosion resistance. Grade 10.9 stud - fear not, big turbo owners.
• Thermal isolation spacer on the hot side to resist heat transfer into the poly
• Engineered in-house and made in America

*Still require a solid mount? Turner Motorsport solid engine and transmission mounts for N52/N54/N55 coming early July 2017.

This item fits the following BMWs:
2008-2013 E82 E88 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 325xi 328i 328xi 330i 330xi 335d 335i 335xi - Sedan
2007-2011 E91 BMW 325i 325xi 328i 328xi - Touring Wagon
2007-2013 E92 BMW 328i 328xi 335i 335is 335xi - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible
2009-2016 E89 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

Whether you are looking to replace your old stock wheel lug bolts, or need longer bolts to accommodate wheel spacers or for other special considerations, our silver wheel bolts are probably what you need. They are high grade (10.9) and feature a durable bright silver finish. These are 12 x 1.5mm bolts with a 17mm head -- as used on most BMWs. Replaces BMW part numbers 36136781150 and 36131095390.

The standard length wheel bolts are for stock BMWs, and the longer length bolts are listed below (select your length with the drop down box) with the size / thickness wheel spacers they are suitable for. Longer wheel bolts are only 20 cents more than standard, and are available in lengths to work with spacers up to 20mm thick. Please select your desired length below (default is the standard/stock BMW length bolt).

Price is for a set of 10 bolts.

These silver wheel bolts fit the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
1977-1983 E21 BMW 320i 320/5 323i
1984-1991 E30 BMW 318i 318is 318ic 325e 325es 325i 325ic 325is 325ix M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive M3 - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
1997-2003 E39 BMW 525i 528i 530i 540i M5
2004-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive 545i 550i M5
1982-1989 E24 BMW 633csi 635csi L6 M6
2004-2011 E63 E64 BMW 645ci 650i M6
1977-1987 E23 BMW 728i 733i 735i 745i L7
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 E85 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe
2009-2015 E89 BMW Z4 sDrive28i sDrive30i sDrive35i sDrive35is
2000-2003 E52 BMW Z8 Roadster
2002-6/2006 R50 MINI MINI Cooper
2005-6/2006 R52 MINI MINI Cooper Convertible, MINI Cooper S Convertible.
2002-6/2006 R53 MINI MINI Cooper S

Full carbon fiber intake to increase flow, performance and aesthetics! Dual inlet design for maximized air flow while retaining the OEM+ fitment.

The most common N55 intake utilizes a short plastic tube and oversized cone filter; it is your job to have better taste than the common N55 owner. This carbon intake changes the whole image of the N55 engine while maintaining a flow of cool air and added induction noise. With a dual inlet design the engine bay retains its functionality while adding a second inlet to provide your engine with improved air flow and sound. To ensure the engine gets the coolest air possible the second inlet is located in the "sweet spot" on the cold side of the engine for the lowest intake air temps and most air flow possible. The cone filter features a bellmouth velocity stack filter that creates the satisfying flutter after letting of the throttle.

Our Turner Carbon Fiber Intakes start with a 3D scan of the factory intake and engine bay. Engineers use the 3D imaging of the chassis to design the intake in SolidWorks modeling software. Using a Flow Bench, the Intake is then airflow tested against the factory intake, to ensure optimal airflow improvement against stock. The final product is a beautiful and functional Carbon Fiber Intake, CAD designed for perfect integration with the OEM inlet ducting and stock mounting locations and proven to flow better than factory.

Key Benefits:

Increased flow over the factory intake
Carbon fiber airbox and intake tube with gloss clear coat for UV protection
CAD-Designed for perfect Integration
Custom high flow air filter specially designed to to pair with the carbon fiber airbox
Kit Contents:

Carbon Intake Tube
Full Carbon 2 Piece Airbox
Bellmouth Velocity Stack Cone Filter
Billet Turbo Inlet Adapter
Silicone Coupler
Hardware For Installation
Design:

- Carbon Fiber Intake Tube

Carbon inlet tube featuring a smoother interior without corrugations for a smooth flow path.
Integrated carbon flange allows secure mounting of the tube to the carbon air boxes.
Intake tube is manufactured using 2x2 twill weave carbon fiber for a great look in the engine bay.
Gloss finish clear coat for UV protection.
4-ply reinforced silicone coupler and 6061-T6 black anodized aluminum flange that utilizes the factory o-ring and retaining clip.
- Air Box

Carbon fiber airboxes are manufactured using 2X2 twill weave carbon fiber and protected with a gloss finish clear coat for UV resistance to match the intake tube.
Air box mounts in stock location with supplied hardware.
- Air Filter

Conical hi-flow reusable air filter; featuring 8 ply oiled cotton gauze construction to maximize filtration efficiency.
Bellmouth (velocity stack) filter flange inlet to reduce turbulence in order to maximize flow.
Product Development:

Turner N55 Intake System was designed, engineered, tested and quality inspected by our Research and Development team at Turner. Nothing but the highest level of precision and quality through leading-edge product development technology including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modeling, rapid prototyping utilizing our in-house 3D printer and rigorous long term product testing. Performance data metrics are collected utilizing Mustang AWD 500 SE in ground dyno and in-house Superflow SF-750 Flowbench.

Fitment:

E82 135i N55
E88 135i N55
E84 X1 35i
E90 335/xi N55
E92 335/xi N55
E93 335/xi N55