Packaged by Turner for BMW 1 Series E82 (2008-2013)

The water pumps in BMW N54 models are known for failure near 80,000 miles. This is a very common issue that often times leaves the owner stranded. This kit provides a single stop for the water pump and thermostat replacement to save the search and get you back on the road.

Included in this kit:

Thermostat
Water pump
Genuine BMW coolant
Mounting hardware required for both the thermostat and water pump

Everything you need to upgrade your front and rear brakes in an afternoon in one simple kit!

By providing it all for you in a single click, this kit has made it easier to get the quality upgrade components you need when beginning a brake service. This performance brake service kit includes rotors, pads, sensors, assembly grease, and set screws to make your brake upgrade easy.

Includes the following parts:

Front ECS 2-piece drilled and slotted rotors Rear ECS V5 drilled and slotted rotors Front and rear ECS EP24 "Enthusiast Performance" Brake Pads Pad wear sensors ECS stainless steel rotor set screws Brake lubricant compound packet Includes ECS Stainless Rotor Set Screws to eliminate rusty factory fasteners

Just like the rest of your vehicle's major systems, the cooling system must also be addressed periodically to ensure proper cooling and component reliability. Plastic and rubber components become brittle and prone to splitting or cracking after long periods of heating and cooling cycles, especially in colder climates! The coolant itself can degrade or become contaminated, leading to potential corrosion or freezing issues. Finally, thermostats and sensors can fail completely, preventing proper cooling and/or coolant temperature readings to become inaccurate.

To make sure you are not left stranded on the side of the road with an overheated engine, we have put together this Basic Cooling System Service kit. This kit contains all of the most-likely-to-fail components, giving you peace of mind knowing your engine will continue to run cool for another 60,000+ miles.

See kit contents below for all included components.

Automatic transmissions are reliable, shift smoothly, and can last without issue so long as they are properly maintained. Over time, the transmission fluid becomes thick and the filter becomes contaminated with small metal particles. This can cause excess wear, high transmission operating temperatures, and eventual failure. To prevent this we recommend changing your filter, fluid, and seals to ensure your transmission continues to operate flawlessly. We recommend filter and fluid changes every 50,000 miles. 

Kit Includes:

• Automatic transmission oil pan with integrated filter 
• Oil pan gasket
• Drain plug with sealing washer
• Fill plug with sealing washer
• 7 quarts Redline D4 automatic transmission fluid

Fits the following BMWs:
E84 BMW X1 xDrive35i
​E90 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission), 330i/xi, 335i/xi
​E91 BMW 325i/xi, 328i/xi (with GA6HP19Z automatic transmission)
​E92 BMW 328i/xi (with GA6HP19Z automatic transmission), 335i/x
​E93 BMW 328i (with GA6HP19Z automatic transmission),  335i
E60 BMW 525i/xi, 528i/xi, 530i/xi, 535i/xi
E61 BMW 525i, 530xi, 535xi
E70 BMW X5 xDrive30i
E71 BMW X6 35iX
E82/88 BMW 128i(with GA6HP19Z automatic transmission), 135i (N54)
F01/02 BMW 740i/Li
E85/86/89 BMW Z4 3.0i/Si sDrive30i M54 N52

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance. 

Included in this E9X BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

• Pagid Front & Rear Brake Pads
• Zimmerman Front & Rear Rotors
• New Front & Rear Wear Sensors
• Brand New Stainless Steel Set Screws
• Syl-Glide Silicone Brake Lubricant 

Fits the following BMWs:
2006-2013 E9X BMW M3
2011-2012 E82 BMW 1M

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Often an oversight in maintenance, ignition components are also susceptible to wear and tear. Spark Plugs can accumulate carbon, reducing the spark intensity and it's ability to properly ignite the air/fuel mixture, leading to misfires and generally declining performance. Other ignition components, such as coils, boots, wires, caps, and rotors, can also wear out over time due to factors like heat and contamination, preventing the current from reaching the spark plug.

To start over fresh with all new components, we now offer these Ignition Service Kits. Each kit comes with brand new OE quality components, replacing any potential fault points in your ignition system for peak performance!

See kit contents below for a complete list of included components.

Don't buy into the hype that your car is maintenance-free! It was only free during the BMW warranty period, which simply deferred maintenance. Take charge of the care and servicing of your investment and it will reward you in driving pleasure and in your bank account. Using a preventative service schedule will not only keep your BMW running like new, but will also prevent a more costly repair and inconvenience in the future. Not to mention, complete and thorough maintenance records can add hundreds or thousands to a selling price of a used car and give a buyer unmatched piece-of-mind.

Our approach to servicing and caring for newer BMW models is not radically different than when we opened nearly twenty years ago. The design and materials of some components have changed but that only affects WHEN you should replace something, not IF. Through our own Service Department, and thousands of sales annually, we have put together packages for your newer BMW model that will reinject some life into your car and keep it performing at its peak. We use Original Equipment (OE) or Original Equipment Manufacturer (OEM) parts that we have trusted since we opened in 1993. In some cases, we recommend a performance alternative part that we have found works better, or resolves a design flaw, with the original. So you get top quality parts, first-rate service, and unbeatable expertise.

The LL-01 BMW oil specification marks stringent requirements from BMW that oil must meet in order to receive this approval rating. Still used today in many BMW NA and Turbo engines, LL-01 TwinPower Turbo 5w-30 and all LL-01 approved oils are great for ensuring proper wear protection and low fuel consumption, even during high oil change intervals. When BMW LL-04 oil was developed, it was not approved at the time for use in the US. This was due to the high sulfur and ethanol content in US fuels. Originally used mostly for diesel engines and euro motors, LL-04 demand is now starting to pick up with changes in US fuels such as lower sulfur content since 2014 and thanks to LL-04 and LL-01 being interchangeable/compatible. The slight advantage of LL-04 over LL-01 is due to LL-04's higher ZDDP levels and HTHS ratings. This allows for increased engine protection at higher temperatures and engine pressures. In addition, LL-04 also has a lower SAPS level which benefits direct-injection engines, including all BMW turbo engines since 2007.

5,000 Mile Oil Service

(click to expand)

• engine oil change with filter, using OE BMW 5W30 or Motul
• replace drain bolt crush washer
• reset oil service/maintenance indicator
• inspect and top off any other fluids

Annual Service

(click to expand)

• air filter cleaning or replacement
• MAF/airflow sensor cleaning
• A/C microfilter/cabin filter replacement
• brake fluid flush/bleeding
• top off power steering fluid (make sure you use the correct Pentosin fluid!)
• wiper blade replacement
• lubricate door hinges and treat rubber door seals
• inspect spare tire or tire repair kit, and tire-changing tools
• inspect drive belt for cracking or stretching
• inspect intake boots and vacuum lines for cracks
• inspect brake system for pad wear, rotor wear, parking brake operation, and brake pedal pressure
• inspect bushing and ball joints for excess play/movement
• ensure the cooling systems are functioning correctly (hoses and thermostat, thermostat housing, auxiliary fan, A/C system, etc)

40,000 Mile Major Service

(click to expand)

• spark plug replacement
• ignition coil and coil boot inspection and replacement
• inspect spark plug cavity in valve cover for leaking valve cover gasket
• engine oil change with filter, using OE BMW 5W30 or Motul
• reset oil service/maintenance indicator
• air filter replacement or cleaning for aFe/K&N type
• fill and bleed cooling system
• manual transmission fluid change, using Red Line ATFD6 or Genuine BMW MTF-LT-3
• differential fluid change, using Red Line 75/90 or Motul Gear300
• brake fluid flush/bleeding
• serpentine belt replacement
• inspect belt roller pulleys (drag and rotation) and belt tensioners
• complete chassis inspection, including: front control arms, tie rods, ball joints, wheel bearings, rear suspension arm bushings, rear upper shock mounts, rear subframe mounts, axle shaft boots
• complete brake system test and inspection
• engine and transmission leak detection and diagnosis
• shifter linkage, driveshaft guibo, CV, and center support bearing inspection
• exhast system inspection, including hanger replacement

80,000 Mile Major Service

(click to expand)

• spark plug replacement
• ignition coil and coil boot inspection and replacement
• inspect spark plug cavity in valve cover for leaking valve cover gasket
• engine oil change with filter, using OE BMW 5W30 or Motul
• reset oil service/maintenance indicator
• air filter replacement or cleaning for aFe/K&N type
• fill and bleed cooling system
• manual transmission fluid change, using Red Line ATFD6 or Genuine BMW MTF-LT-3
• differential fluid change, using Red Line 75/90 or Motul Gear300
• brake fluid flush/bleeding
• fuel filter, pressure regulator replacement
• serpentine belt replacement
• replace belt roller pulleys and belt tensioners
• complete chassis inspection, including: front control arms, tie rods, ball joints, wheel bearings, rear suspension arm bushings, rear upper shock mounts, rear subframe mounts, axle shaft boots
• complete brake system test and inspection
• engine and transmission leak detection and diagnosis
• shifter linkage, driveshaft guibo, CV, and center support bearing inspection
• exhast system inspection, including hanger replacement
• water pump and thermostat inspection or replacement. The water pump on this car is electric and will not display warning signs of impending failure. The output of the water pump can be tested however, and your local full-service BMW repair shop should have the diagnostic tools to perform this test.

You may also want to pick up these other helpful items:

• E90 Bentley Service Manual (not specific to the 1-series but still very helpful)
• We offer many DIY-related tools, specifically for the 135i owner -
  drain plug sockets, fluid suction and bleeder pumps, spark plug sockets and install guides, oil filter cap adapter, oil funnels, and more!
• SprintBooster throttle enhancement
  
• This package fits the following BMWs:
  2008-2012 E82 BMW 135i
  2008-2012 E88 BMW 135i Convertible
  
  
  
  Put a check in the boxes next to the items you wish to order.

When replacing your worn out brakes, the market is flooded with performance options. If your BMW doesn't see track time, it's not very practical. Performance pads and rotors tend to result in a lack of bite at low braking temperatures and cause excessive noise in daily driven vehicles that becomes irritating. BMW brakes from the factory are perfectly suited for trips around town, across the country, and even the occasional spirited driving session, delivering smooth, quiet, and long lasting performance.

Included in this BMW brake package are all of the OEM equivalent components needed to replace your Front & Rear brakes with comfort, reliability, and optimal lifespan in mind.

Brake components in this kit:

Textar Front & Rear Brake Pads
Zimmerman Front & Rear Rotors
New Front & Rear Wear Sensors
Brand New Set Screws

The external temperature sensor on a BMW is placed within the underbody plastics that extend very close to the road. As a result it's easy to damage by rolling into a low curb or parking lot tire stop. The first sign you may have a problem with your external temperature sensor is if you have a really low reading. This is caused by the sensor either being damaged, missing or having an open circuit; the wires leading to the sensor may have torn off in an impact.

Includes solder filled heat shrink connectors, contact leads with wire, plug housing, temperature sensor, 10 pack of zip ties, and a panel mount zip tie for mounting the sensor.

This packages covers the major components you would install along with a new water pump or thermostat. On the N54 cars (135i, 335i, 535i) the water pump and theremostat are mounted together. In fact, to get to the thermostat, BMW expects you to remove the water pump. This package covers the whole job. With the electric water pump now an integral part of the efficiency and performance of the engine, staying on top of its maintenance and replacement is the smart thing to do.

Our water pump/thermostat overhaul includes:

• OEM VDO electric water pump, p/n 11517588885 or 11517632426
• OEM mounting screws for water pump (set of 3), p/n 11517602123
• OEM Behr thermostat, p/n 11537549476
• Original BMW connecting hose from thermostat to water pump, p/n 11537545665
• Original BMW hose clamps for hose (x 2)
  
• BUY AS A PACKAGE AND SAVE $$!
  
  The water pump on the N54 engine has more cooling responsibilities than ever before. Not only must it provide cooling for the engine, but it's also pumping fluid used to cool the turbocharger oil and automatic transmission oil. The good news is that the pump only works when, and only as much, as it needs to. The engine computer dictates how much fluid needs to be pumped through the system depending on the load. That means the system can actually stop the pump when warmer temperatures are needed. No longer is the pump spinning all the time from an engine-driven belt. The bad news is that it's now an electrical part, so a failure is usually immediate and with no warning. And if the electronics are at fault, there is no way to rebuild or repair it. Fortunately, the engine computer will force a shut down or reduce power if a problem occurs, preventing catastrophic engine damage.
  
  How to avoid a water pump failure in the future? Replacing the water pump as part of a regular interval schedule will ensure you always have a functioning pump in place. Since this technology is relatively new for BMW, therefore the lifecycle of the pump isn't yet known, we have been recommending replacement every 80-100k miles. This package of OE/OEM parts covers everything with Original BMW coolant offered to finish off the job. A proper bleeding procedure must be followed with the new electric pump.
  
  This water pump package fits the following BMWs with the N54 engine:
  2007-2010 E60 BMW 535i 535xi 535i xDrive
  2008-2010 E82 BMW 135i
  2011-2012 E82 BMW 1M Coupe
  2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
  2007-2010 E92 BMW 335i 335is 335xi 335i xDrive - Coupe
  2007-2010 E93 BMW 335i - Convertible

N54 HPFP failure is common with BMWs that use this powerplant. Our Packaged by Turner N54 High Pressure Fuel Pump Replacement Kit includes everything you need to replace your N54 HPFP.

Kit includes:

• Genuine BMW Re-manufactured High pressure fuel pump
• Intake manifold gasket sets  
• Throttle body gasket 
• Low pressure fuel sensor 
• High pressure fuel sensor 

Front Wheel Hub Assembly with Bearing fits BMW E90 E92 E82 E84 E89. This is the OEM FAG brand. Requires 4 wheel bearing hex bolts - #3112676203 per wheel bearing.This bearing can be used on the left or right side. Sold individually.

FAG is an OE supplier to BMW as well as several other German marques. 

GSP is a high-quality supplier for aftermarket suspension components. They have quickly position themselves as an industry leader, and pride themselves on offering high-quality alternatives to their expensive OEM counterparts.

This item fits the following BMWs:
2008+ E82 BMW 128i 135i 135is
2006-2011 E90 BMW 325i 328i 330i 335d 335i - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2013+ E84 BMW X1 sDrive28i
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is