BMW Suspension Parts for BMW 1 Series

The H&R Coil Over kit takes the traditional shock/spring package one step further. H&R combines their progressive-rate springs with specially valved shocks and adds height adjusters that let you set the ride height to your own personal tastes. These coil overs are designed for street use with progressive rate springs that start out soft and stiffen as they are compressed. This helps to keep the ride compliant while still giving better handling and balance.

H&R designs each suspension to work as a coil over. This means that the correct amount of travel has been built into each shock. And the shocks are valved specifically for the spring rates to give a tight and controlled ride without being harsh or ultra-stiff. Each H&R coil over is TUV tested and approved and meets ISO quality standards. These are used with the stock strut and shock mounts for a quick and easy install.

SPECIAL PRICING FOR A VERY LIMITED TIME!
FREE GROUND SHIPPING


Height adjustment range:
F: -1.2-2.5"
R: -1.0-1.75"

Eurotuner Magazine did a full tech article on installing this H&R coil over kit in a 135i. For the complete writeup, click here (E82 135i H&R Coil Over).

This coilover fits the following BMWs:
2008-2012 E82 BMW 128i 135i

H&R has introduced this Street Tuner CoilOver suspension kit for the 1M that has several unique features for the discerning enthusiast. H&R has designed this premium coil over specifically for the 1M using new materials and features not found on a typical 135 or M3 kit. The key features of this kit are the aluminum rear shocks with solid, Heim-joined lower mounts. The lighter weight from the aluminum and the free motion from the lower monoball makes for a more efficient shock motion and better response from the suspension. Combine these with our monoball upper shock mounts and you have race-bred shock technology for the ultimate BMW driver's car. H&R finely-tuned the rear shock dampening to reduce wheel hop. The wheel hop is inherent in the 1M and these H&R rear shocks go a long way in eliminating it. The front struts are a true nickel-plated, threaded body replacement for the stock strut. All four progressive-rate springs are included and rear aluminum ride height adjusters complete the set. You'll find this kit on H&R's own Project 1M so it has been dialed in by some of the best suspension engineers in Germany and the USA.

These 1M Coil Overs are height adjustable in the front and rear using spring perches associated with each spring. This helps to improve handling by lowering the center of gravity, reducing bodyroll with a stiffer spring, and reducing the unsightly wheel-fender gap.
Front Adjustment Range: -1.2 to -2.3 inches from stock
Rear Adjustment Range: -0.3 to -1.3 inches from stock

SPECIAL PRICING FOR A VERY LIMITED TIME! 
FREE GROUND SHIPPING 

This coil over fits the following BMWs:
2011+ E82 BMW 1 M Coupe

BMW’s are known to have failure prone front thrust arm bushings.  The flexible rubber bushings, even those found in M performance models, allow significant movement of the front wheels to maximize daily driving comfort, but also allow considerable alignment change.  This results in a disconnected and numb road feel, standing between you and a confidence inspiring driving experience.  Eventually the fluid filled rubber bushings fatigue and crack due to continual deflection and ozone degradation, and eventually the damping fluid leaks out resulting in complete failure. 

For the enthusiast looking for superior performance and longevity with a crisp, confidence-inspiring driving experience, our sealed ball joint monoballs are the best solution available!  Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer E31, E32, E34, E38, E39, E53, E60, E63, E64, and E83 owners similar levels of handling precision and control for the track and street. 

The bearing housing is precision CNC machined from 6061-T6 anodized aluminum and features a knurled OD to ensure a perfect press fit, and utilize a sealed OEM BMW ball joint for exceptional quality and durability, making them completely at home on both the street and track with no compromise.  We have done extensive street, autocross, and track testing to ensure the ball joint used in this bushing design excels in each setting.  The advantage of a sealed ball joint is that it eliminates all unwanted deflection while still allowing complete bind-free movement throughout suspension travel, resulting in exceptional control of wheel alignment.  What you get is superior steering precision, turn-in response, direct braking feedback, and better handling.

In short, if you're seeking the ultimate in precise, predictable handling and control, with crisp braking response and a long service life that’s equally at home on the street or track - look no further. We have you covered.

We offer these thrust arms with the monoball bushings pre-installed for your convenience. Since BMW recommends the control arms be replaced for every other bushing change, we prefer to sell these as a pre-assembled set. The bushings are also available separately if you wish to source your own control arms.

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum
• Knurled OD to provide the perfect fit for the wide range of thrust arm bore diameters among brands.
• CNC machined 304ss ball joint sleeve inserts, providing a precision fit between the ball joint and the subframe. 

Bearing

• OEM BMW sealed and greased ball joint for exceptional durability and service life.

Performance

• Nearly instantaneous, crisp steering and braking response.
• Maintenance free, long lasting performance. 
• Improved road feel without undesirable NVH.

Sold as a pair for RWD models only.

Click here for installation instructions.

This item fits the following BMWs:
2008-2012 E82 BMW 128i 135i 1M Coupe
2006-2011 E90 BMW 325i 328i 330i 335d 335i M3 - Sedan
2006-2012 E91 BMW 328i - Wagon
2007-2013 E92 BMW 328i 335i 335is M3 - Coupe
2007-2013 E93 BMW 328i 335i M3 - Convertible
2009+ Z4 BMW Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Our E90 E92 E93 fixed camber plates are designed from the knowledge we gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. Our camber plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to -2.5° depending on your individual suspension setup, while only increasing ride height by 6mm. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Fixed mount camber plates are legal in many racing and autocross classes - these are the perfect camber solution when adjustable plates are not allowed in your class.

These are very simple to install, requiring only pressing out locator dowels and studs in your factory strut mounts. See below for detailed instructions.

Koni suspension has taken their long running FSD (Frequency Selective Dampening) Technology and improved upon it to create their new Special Active suspension package. Improving handling while also improving the comfort of your BMW's ride, Special Active shocks and struts prove they are a top contender in the replacement suspension market.

Koni's Special Active dampers adapt to the continuous imperfect road conditions in order to provide you with a more responsive and smoother ride. Thanks to multiple generations of suspension expertise, these shocks and struts rival expensive ride control systems of newer vehicles but at a cost that is significantly lower and a capability to be retrofitted into existing vehicles.

Designed by Koni for the vehicle's original stock ride height, these are not intended to be used with lowering springs and will perform best when paired with stock springs.

Koni Special Active Features:

• KONI’s latest generation of Frequency Selective Damping Technology
•  Improves safety and road holding
•  Technology proven on over 1.5 million factory equipped vehicles
•  Secure and stable feeling for spirited driving
•  Unrivaled aftermarket solution can be fitted to most new and older cars
•  Driving refinement for cars, trucks, SUVs, etc.
•  Technology that rivals expensive Original Equipment electronic systems
•  Performance for driver and comfort for passengers in one

Activate your Koni Rebate!

Fits the following BMWs:
2008-2013 E82/88 BMW 128i/135i without EDC

Rubber mounts in any position of a vehicle are usually designed with comfort and longevity in mind leaving performance as a sacrifice. This kind of sacrifice here at Turner just won't do, so we did what we do best and designed a solid monoball mount.

Our engineering team first wanted to tackle the issue with wear found on rubber mounts. Due to their combination of steel, rubber, and low mounting location, these mounts are a direct target for deterioration and failure. As they are positioned out in the open and exposed to the elements, bonded steel and rubber components inevitably hold moisture, separating as the steel bearing begins to rust. Our solution was to offer a rebuildable mount with a Teflon lined bearing for increased durability, combined with a blue anodized body and melonite coated bushing sleeves for corrosion resistance.

The performance side of these mounts is primarily found in the articulation allowed by the bearing. Rubber mounts do not allow for proper free damper movement, hindering shock performance. By eliminating the deflection found in factory rubber mounts and allowing full shock articulation, this solid monoball design eliminates slop and maximizes shock efficiency and performance, allowing for more predictable handling on the street or the track - with almost zero added noise, vibration, and harshness.

Replaces OE part #: 33526768544

Key Benefits:

• Monoball rear lower shock mount eliminates unwanted deflection, maximizing shock efficiency and performance.
• Allows full shock body articulation for low friction movement and reduced side loading and improved shock wear.
• Designed to work with stock non-M taper seat stud style shocks (not M eyelet mount type).
• Maintains OE shock position

Design features:

• Rebuildable using off the shelf bearings - these are the last rear shock mounts you’ll need to buy
• Includes new hardware
• Made in USA

Housing:

• Billet CNC 6061-T6 aluminum housing, type II anodized for exceptional durability and corrosion resistance

Bearing:

• FK WSSX14T teflon lined spherical bearing
• 440C heat-treated stainless steel ball, 1 ⅜” ball dia.
• 17-4 PH heat-treated stainless steel race
• Self-lubricating PTFE liners are chemically bonded to the inner diameter of the race to offer a very high load-carrying capacity with greatly increased dynamic wear characteristics.
• Static Axial Load Rating: 10,800 lbs.
• Rod End Misalign Angle: 6 degrees

Bearing inserts:

• CNC machined 1144 steel, heat treated and melonite coated designed to maximize ball articulation while offering exceptional durability and corrosion resistance.

This item fits the following BMWs: 
2008-2013 E82 BMW 128i 135i 135is Coupe 
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335d 335i 335xi 335i xDrive - Sedan 
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon 
2007-2013 E92 BMW 328i 328xi 328i xDrive 335i 335is 335xi 335i xDrive - Coupe 
2007-2013 E93 BMW 328i 335i 335is - Convertible 

KONI's entry level performance STR.T (pronounced Street) shocks and struts bring improved handling and KONl quality to the budget minded driving enthusiast. Whether to simply refresh and upgrade a stock vehicle or to match with street performance lowering springs and other modifications, KONl STR.T provides performance at a value price point. 

• Entry level performance shock absorber
• Compliments lower springs
• Perfect for OE replacement or vehicle improvement
• Non-adjustable
• Lifetime Warranty

Activate your Koni Rebate!

This kit fits the following BMWs:

E82 E88 128i 135i

E9x RWD non-M 323i 325i 328i 330i 335d 335i 335is

KONI's entry level performance STR.T (pronounced Street) shocks and struts bring improved handling and KONl quality to the budget minded driving enthusiast. Whether to simply refresh and upgrade a stock vehicle or to match with street performance lowering springs and other modifications, KONl STR.T provides performance at a value price point. 
 

• Entry level performance shock absorber
• Compliments lower springs
• Perfect for OE replacement or vehicle improvement
• Non-adjustable
• Lifetime Warranty

Activate your Koni Rebate!

This kit fits the following BMWs:
E82 128i 135i

E9x 323i 325i 328i 330i 335i (RWD non-M cars only)

KONI's entry level performance STR.T (pronounced Street) shocks and struts bring improved handling and KONl quality to the budget minded driving enthusiast. Whether to simply refresh and upgrade a stock vehicle or to match with street performance lowering springs and other modifications, KONl STR.T provides performance at a value price point.

• Entry level performance shock absorber
• Compliments lower springs
• Perfect for OE replacement or vehicle improvement
• Non-adjustable
• Lifetime Warranty

Activate your Koni Rebate!

This kits fits the following BMWs:
2008-2013 E82 BMW 128i 135i 135is
2006-2011 E90 BMW 325i 328i 330i 335d 335i  - Sedan
2007-2013 E92 BMW 328i 335i 335is  - Coupe
2007-2013 E93 BMW 328i 335i 335is - Convertible