BMW Engine Parts for BMW 3 Series E93 (2007-2013)

Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.

Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.

From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.

As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

Upgrade your BMW's oil pressure sensor setup with the Oil Distribution/Sending Block. This versatile block is designed to mount in the stock oil pressure sensor location on the oil filter housing or in the original location on the engine block. It allows the use of up to two aftermarket sending units (not included) along with the factory sensor, providing accurate pressure and temperature measurements. Engineered for reliability and cleanliness, it ensures a reliable setup for your BMW's oil pressure monitoring needs.

• Mounts in stock oil pressure sensor location for easy installation
• Allows use of up to two aftermarket sending units in addition to the factory sensor
• Incorporates factory sending unit for utilizing the factory oil pressure light
• Threaded for one M12x1.5 port and two 1/8th NPT ports for versatility
• Includes banjo bolt and crush washers for secure installation
• Compatible with various BMW engines including M20, M42, M50, M52, M54, N52, N54, S50, S52, S54, S65, M10, S14, and M30

• 11127582245 - N52 valve cover gasket set
• 11127552280 - N52 eccentric shaft sensor seal
• 11127559699 - N52 Valvetronic gasket

Stainless steel filtration is not a new technology but is quickly gaining popularity in the automotive segment. With the ability to filter down as small as a paper filter element with the ability to be washed and reused!

The K&P Engineering filter element is made from medical grade, type 304 stainless steel micronic filter cloth to provide unmatched protection against oil contamination and resultant engine damage. A one inch square of this material flows an incredible 1.9 gallons of oil per minute at only 1 PSI pump pressure. The adhesive used in the filter assembly process is good to 600 degrees Fahrenheit, far above normal engine operating temperatures. A super strength nickel-plated neodymium rare earth magnet is installed in the top of the element for magnetic pre-filtering of the oil. The sophisticated bypass is engineered for proper differential pressures and consistent operation, delivering a greater percentage of filtered oil while being very easy to clean. The twist lock design assures positive filter element placement and allows for easy disassembly, inspection, and cleaning. The quad-ring gasket doubles the seal between the filter and the engine. Finally, the filter housing is carved out of solid 6061T6 billet aluminum, which not only looks trick but aids in dissipating heat.

K&P Engineering manufactures stainless steel filters for a vast array of engines around the world. Staying at the forefront of design and testing allows this company to offer a top tier product for your European vehicle.

Features:

• Consistent filtering across entire filter surface
• Superior ASTMF316 filtration performance
• Magnetic Prefiltering
• Progressive rate bypass combined with high flow characteristics of the filter media avoids unfiltered oil bypassing the filter during cold startup and high rpm
• Easy inspection of engine contamination
• Proven in Motorsports, Military and Aerospace applications for years. Technology is FAA approved for use in aircraft. 

At regular oil changes, clean to K&P's specifications for continued used - a true lifetime filter.

This part fits the following BMWs:
2012+ F30 3 Series Sedan 328i 328iX 328i 328iX 335i 335iX 
2006 - 2013 E9X 323i 325i 325xi 328i 328xi 330i 330xi 335i 335xi
2010 - 2016 F10 5 Series Sedan 528i 528iX 530i 535i 535iX 
2003 - 2006 E60 Sedan 525i 525xi 530i 530xi 
2007 - 2010 E60 528i 528xi 535i 535ix 
2009 - 2016 E89 Z4 Roadster Z4 sDrive28i Z4 sDrive30i Z4 sDrive35i 
2014+ F22 2 Series Coupe 228i 228iX M235i M235iX
2007 - 2013 E88 1 Series Convertible 128i 135i
2008 - 2013 E82 1 Series Coupe 128i 135i 135is 1M Coupe
2012 - 2013 E70 X5 xDrive35d X5 xDrive35i
2007 - 2011 E70 X5 3.0sd X5 3.0si