BMW Engine Parts for BMW 3 Series E93 (2007-2013)

The VANOS system on your N51, N52, and N54 engine controls the valve timing inside the engine. The system is hydraulically operated based on instructions from the engine computer. It's very complex and BMW has not yet perfected the system. The VAN0S solenoid is the actuator that takes instruction from the ECU and activates the VANOS unit on the front of the engine. When the solenoid is failing (or failed) you can end up with a rough running engine, misfires, bad fuel economy, lack of power, and more. It should trigger multiple fault codes and a check engine light for misfires, camshaft control, VAN0S solenoid, boost pressure control, and maybe others. It's important to thoroughly troubleshoot fault codes but VAN0S solenoids are a known issue with these engines.

The VANOS solenoids are located on the front of the engine and may be replaced without removing many other components. In some cases, you may be able to remove the suspect one, clean it, reinstall, and reset your fault codes. If your fault codes come back it's a strong indication that a replacement is required. Or you can buy the new solenoid and replace instead of doing the work twice.

VANOS solenoid for the intake and exhaust are the same part number. Order 2 if you want to replace them both.

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

We recommend replacing the solenoid sealing gaskets as well when replacing the solenoid. You can find these under T#363393

This item fits the following BMWs:
2008-2012 E82 BMW 128i 1M Coupe
2008-2010 E82 BMW 135i
2006-2011 E90 BMW 325i 325xi 328i 328xi 328i xDrive 330i 330xi 335is - Sedan
2006-2010 E90 BMW 335i 335xi 335i xDrive - Sedan
2006-2012 E91 BMW 325xi 328i 328xi 328i xDrive - Wagon
2007-2013 E92 BMW 328i 328xi 328i xDrive 335is - Coupe
2007-2010 E92 BMW 335i 335xi 335i xDrive - Coupe
2007-2013 E93 BMW 328i - Convertible
2007-2010 E93 BMW 335i - Convertible
2006-2010 E60 BMW 525i 525xi 530i 530xi 528i 528xi 528i xDrive 535i 535xi 535i xDrive
2011 F10 BMW 528i
2006-2010 E83 BMW X3 3.0i X3 3.0si
2007-2013 E70 BMW X5 3.0si
2006-2008 E85 BMW Z4 3.0i Z4 3.0si
2009-2011 Z4 BMW Z4 sDrive30i Z4 sDrive35i Z4 sDrive35is

When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.

Genuine BMW Cylinder Head Gasket Asbestos-Free - 1,20Mm
This item fits the following BMW Chassis:
E71,E82,E90,E92,E93,F06,F10,F12,F13,F15,F16,F22,F25 X3,F26 X4,F30,F32,F33,F34,F36

Fits BMW Engines including:
N55

Oil venting and circulation continues to be a problem on BMW engines and now even more so on the turbocharged N54 and N55 engines. The existing stock system does a very poor job of separating fluid and vapor and this leads to an oily film or even small pools of oil throughout the turbos and intake. We're seeing a lot more 135 and 335 cars with drivability and performance issues because oil has sneaked by the ring seals and is coating the intake piping, intercooler, intake valves, and other critical areas. The problem is worsened with higher boost levels. Oil is excellent for lubricating moving parts but terrible when it gets into the combustion chamber, effectively lowering the octane rating and reducing performance. Our own shop has gone the extra step and offers media blasting of the intake valves to strip away the oily buildup we have seen.

Our shop also strongly recommends an oil catch can be installed in the line for the crankcase vent. The oil catch can traps oil as it leaves the valve cover and holds it in a canister. This catch can is located on the cooler side of the engine where the oil will condense easier and stay in the can. Whatever minimal vapors are left over in the oil is then vented back through the canister and into the intake where it is safe to be burned up in the engine or recirculated back through the system again. This is the way the system was designed! At each oil change simply unscrew the canister and empty the trapped oil with your regular used oil. The Burger Tuning oil catch can is the best we have seen so far. Installing one of these will avoid costly repairs in the future and help maintain your boost and performance. It's one of the smartest modifications you can make because it demonstrates a well-thought out tuning strategy and care for the condition of your engine.

The BMS Oil Catch Can is made from aluminum and with a stealthy black anodized finish. It installs on the cooler side of the engine with a dedicated bracket and new oversized vent lines. The location is key as heat will evaporate the oil and send too much vapor back into the engine (where cooler air will turn it back into fluid). The BMS OCC also has a factory-like appearance. Since BMS designed their catch can from scratch they can guarantee it fits and performs correctly for the N54/N55 engine, unlike other catch cans on the market that are poorly retrofitted from other applications and under-sized for the N54 engine.

Note: Since the crankcase vent system is considered part of the overall emissions system, installing this may be a violation of local, state, and federal laws. While exemptions are made for track/race and off-road use, check with your local state inspection facility on using this in street-driven vehicles

BMS Oil Catch Can Features:
+ Increases air intake efficiency
+ Promotes engine longevity
+ Double-baffled design allows excellent air/oil separation
+ Large In/Out ports (no tapered sizes that slow flow)
+ Stealth mounting on cooler side of engine bay (promotes condensation of oil to vapor)
+ Anodized black lightweight aluminum
+ N54 version mounts out of sight under the cowl
+ Made in USA with a lifetime guarantee