BMW Wheels - Genuine & Performance for BMW 2 Series F22 (2014+)

• 70MM, 80MM, OR 90MM OVERALL LENGTH
• OUR HIGHEST-GRADE PREMIUM WHEEL STUD
• DRY LUBE WITH BLACK M-PHOSPHATE COATING
• STUD FOR RACE/TRACK USE
• CORRECT SHOULDER SIZE FOR A WIDE RANGE OF HUBS/BRAKE ROTORS
• USE WITH 14x1.5 NUT
  
• For the very best in a race-grade wheel stud, stop looking! These are the wheel studs that our race teams insist on (after years of trying every stud design on the market). MSI Racing specializes in hardware for motorsport use (NASCAR and IMSA) and other advanced industries. We tried them on our Grand-Am/IMSA racecars and were very impressed by the performance and durability of their designs. Race wins and championships can come down to the seconds of a pitstop. We could run any wheel stud in the world and we use these. After testing them over the course of a few endurance seasons we decided to offer them to all of our customers as well.
  
  These studs are available in three overall lengths - 70.5mm, 80.5mm, and 90.5mm. All sizes are made with aircraft quality alloy steel and have roll formed threads for greater strength than cut threads. We use a dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish. Manganese is preferred over the more common zinc because it's better at reducing friction and wear to prevent thread galling. With the dry lube applied over the phosphate this is the best corrosion resistance we have seen in any wheel stud! Salt tests have shown this stud is superior to others in corrosion resistance. The dry lube helps the nut engage and glide over the threads for faster engagement without cross threading or binding. Other features of our MSI studs include a large bullet nose nut-starter and a properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  We configured these studs to have a 14x1.25 thread to go into the wheel hub. But the exposed stud has 14x1.5 threads. We did this because threading a nut is faster on 1.5 threads than a finer 1.25 thread pitch, which saved us time during pitstops. There are also more wheel nut options in 14x1.5. When you order our 14x1.25 studs make sure you also order the 14x1.5 nuts.
   

  FREE red threadlocker with purchase of a full set of wheel studs (16 or more)MSI Dry Lube Bullet Nose Wheel Stud Features:
  

• Dry film lubricant HM-30 coating containing Teflon & Moly over a manganese phosphate finish
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Properly sized shank to work with a wide range of brake rotor, wheel, and nut combinations
• Heat-treated aircraft quality alloy steel
• Developed from over 20 years of top level NASCAR use
  
• These studs are installed using the traditional 'double-nut' method (one regular nut and one jam nut) with thread locking compound (Red Turbo-Lock or similar).
  
  Sold per stud.
  Wheel nuts sold separately.

Hub Extenders are the solution that no one else has! BMW wheels must fit on a hubcentric lip to be securely (and safely) mounted to the hub. But with a 3, 5, 8, or some 10mm spacers on a lip measuring no more than 11mm that presented a huge problem - there would be no lip left over for the wheel to rest on! As one of the world's leading BMW tuners and race teams, we came up with a way to extend the lip and get back the lost surface area for the wheel to safely mount on. Our Hub Extenders are the first of their kind.

Hub Extenders fit where the stock dust cap is usually fitted on the front wheel hub. Pop out the dust cap and tap the Hub Extender into its place. It becomes an extension of the original lip. These will only work on the front hubs of the cars listed below because the rear hub is tapered inside (narrows down). These will not work with Xi AWD models because the front axle shaft protrudes through the hub. With Hub Extenders in place you can use nearly any flat wheel spacer - 3mm, 5mm, 7.5mm, 10mm, or possibly more without worrying that the wheel will not be securely seated. This is perfect for wheels that have chamfers on the back of the wheel that don't match up to existing spacers (Kosei K1 spacers for example).

Turner Hub Extender Features --

+ hub extension makes flat spacers a true hubcentric fitment
+ precise tolerance fitment thanks to CAD process and CNC mill machine
+ aerospace grade aluminum  light weight but very strong with a high resistance to corrosion
+ additional military-spec hardcoat for further corrosion resistance
+ stealthy black color with laser engrave Turner logo
+ Turner Motorsport track and street tested!
+ Made in the USA

Wheel Limitations. Special consideration needs to be taken since wheel design and manufacture differ from brand to brand. The key dimension is the dept of the center bore. Some wheels won't work with larger spacers and a Hub Extender because of the additional protrusion into the center bore. Please measure your wheel to make sure it can accommodate an extra 2.5-5mm of hub extending into the center bore. Click here for a diagram.

Hub Limitations. BMW has multiple hub designs but not all are compatible with our Hub Extenders. The inside lip of the hub must be flat and smooth for at least 13mm (the depth our Extender fits into the hub). Some BMW hubs have a bowl shape or have tapered inside walls which will prevent the Hub Extender from seating all the way. Remove the hub dust cap to check before opening your Turner Hub Extenders.

This item fits the following BMWs:
2014+ F22 F23 BMW 228i M235i
1988-1991 E30 BMW M3
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3
10/2013+ F30 BMW 320i 328i 335i - Sedan
10/2013+ F31 BMW 328i - Wagon
10/2013+ F34 BMW 328i - Gran Turismo
10/2013+ F32 BMW 428i 435i - Coupe
10/2013+ F33 BMW 428i 435i - Convertible
10/2013+ F36 BMW 428i 435i - Gran Coupe
1982-1988 E28 BMW 524td 528e 533i 535i 535is M5
1989-1995 E34 BMW 525i 530i 535i 540i M5
1982-1989 E24 BMW 633csi 635csi M6
1988-1994 E32 BMW 735i 735il 740i 740il 750il
1995-2001 E38 BMW 740i 740il 750il
1990-1999 E31 BMW 840i 840ci 850i 850ci 850csi
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

• 60MM, 75MM, 82MM, OR 90MM OVERALL LENGTH
• EASY INSTALL WITH ALLEN SOCKET
• CERTIFIED ISO/TS 16949 AND ISO 9001 BY TUV
• MANUFACTURED IN EUROPE
• BLACK M-PHOSPHATE COATING
• CORRECT SHOULDER SIZE FOR HUBS/BRAKE ROTORS
• STUD FOR MIXED STREET/TRACK USE

• Wheel studs are among the safest and most beneficial upgrades you can make on a track car. Not only are wheel studs safer than wheel bolts but they make changing wheels/tires much easier. One of the frustrating things about installing your wheels on the hub is that it's difficult to line up the wheel on the bolt holes. As wheels get larger but also heavier it's even more trouble. Add in a wheel spacer and the task is twice as hard. BMW does produce a wheel alignment pin for this purpose but if you're changing wheels often a stud conversion is the better way to go.
  
  Our original bullet nose studs are available in 60mm, 75mm, 82mm, or 90mm. The 75mm works great for cars that do not use a spacer (or a spacer smaller than 10mm). We recommend the 90mm length for cars that have spacers up to 20mm. The 82mm length is a happy medium between the 75mm and the 90mm. These studs come with a OEM-style black zinc coating for excellent corrosion resistance. These studs are perfect for dual-purpose street/track cars. The studs are stronger and safer than wheel bolts with protection against corrosion which makes them suitable for street use. For a dedicated race or track car, where wheel changes or pit stops are more frequent, check out our racing dry lube studs.
  
  Our studs are also designed and manufactured with the properly sized shank to work with a wider range of BMW wheel, nut, and brake rotor combinations. We intentionally avoid the extra large shoulders you see on other studs because they can interfere with some brake rotor hats. The extra large shoulder can be too large to allow the rotor to pass through and drilling out the holes is required (not cool!) Our studs have the sufficient shank for the brake rotor without interfering.
  
  Not all wheel studs are created equal. We don't take a manufacturer's generic wheel stud from their catalog and call it our own. Turner Wheel Studs are manufactured to meet our own specifications. Beware of cheaper studs on the market! We have seen other studs similar to our own designs that are not a true BMW fitment. There are differences that we have ironed out over our years of selling wheel studs for the BMW market. Our stud prices may be slightly higher than the rock bottom prices on the web but we promise that it's a higher quality.
   Turner Bullet Nose Wheel Stud Features:

• Black phosphorous corrosion resistant coating
• Innovative nut-starter and bullet shape radius that all but eliminates cross-threading
• Long shank for good brake rotor alignment
• Heat-treated aircraft quality alloy steel
• Installation Instructions
  Click here for installation instructions and more information.
  
  
  
  Sold per stud.