Intercooler for BMW 4 Series F32 (2014+)

Engines make more power when you're able to move as much air and fuel as possible through them. However, air density is just as important as air volume. Cooler air is denser air, so in addition to keeping your engine cool, it's important to make sure that your intake charge is as cool as possible. Turner Motorsport's upgraded intercooler works to reduce air temperatures with a bare minimum of pressure drop. Less pressure drop means less restriction, and a turbocharger that doesn't have to work as hard. This results not only in a longer service life for your turbocharger, but a substantial increase in performance as well.

The stepped design increases volume and surface are in a limited space by adding an additional smaller core at the top of the intercooler. Both cross sectional area and frontal surface area are increased by a whopping 56%, with a design that still weighs under 20 pounds. On the stock intercooler, the temperature differential between the inlet and outlet sides of the intercooler represented a 95 degree drop. With the Turner Motorsport intercooler, that drop was increased to a chilling 140 degrees. The dyno results don't lie: as a bolt-in upgrade, expect gains of 18 wheel horsepower and 10 lb/ft of torque. With a tune and supporting modifications, further gains are possible, up to 36 horsepower and 28 lb/ft of torque.

This cast aluminum intercooler features an attractive, easy to clean matte black finish, with etched Turner logos on the front and bottom. If you're looking for the ultimate cooling system upgrade for your turbo BMW, look no further.

• Cast aluminum construction
• Bar and plate design
• 56% increase in frontal surface area & cross sectional area
• Decrease in temperature of 45 degrees from inlet side to outlet side (95 degree drop stock on outlet side vs. 140 degree drop on Turner outlet side)
• Significantly less restriction (pressure drop of consistently 0.75 psi vs. 1.5-2.5 psi stock)
• +18HP/10TQ (+36HP/28TQ with tune and supporting mods)
• Weighs under 20 lbs.
• Overall size: 520mm wide, 210mm tall
• Mounting hardware inlcuded

Upgrade to the following OE Intercoolers: 17517600531, 17517600530, 17517618809

Fits the Following BMWs:

F22 F23 228i 228i M235i M235ix

F30 F31 F32 F33 F34 F36 328i 328ix 335i 335ix 428i 428ix 435i 435ix

This BladeRunner Intercooler represents the next generation of intercoolers. Designed specifically for the 2012-2016 BMW 328i (F3X) 12-16 L4-2.0L (t) with the N20 engine, this BladeRunner intercooler utilizes a 5" bar and plate core design. This design outflows the factory tube and fin core design, while the 3/16" TIG-Welded end tanks offer superior strength and durability. In testing, this intercooler showed flow gains up to 21% and lowered the intake air temperatures.

End Tanks: 
The unique BladeRunner end tanks are constructed out of 3/16" thick aluminum plates and include two 1/8" NPT ports for sensors or water-methanol injection.

5" Bar and Plate Core Design:
The use of the bar and plate core design allows for greater airflow and increased heat dissipation over the much smaller tube and fin design used by the factory.

TIG-Welded:
100% TIG-Welded inside and out by a certified craftsmen for strength and durability. TIG-Welding provides the strongest welds while reducing stress cracks.

Pressure Tested: 
The BladeRunner Intercooler is test pressure rated at 200psi.

Cold Side Tube:
Constructed of 2-1/2" to 2-3/4" mandrel-bent aluminum tubing and powder-coated wrinkle-black for heat and corrosion resistance. The smooth transition mandrel bends decrease turbulence which increases horsepower and torque. The high-temp wrinkle-black powder-coating insulates the tube from engine heat and protects the tube from corrosion. Includes stainless steel clamps for a leak-free seal and heavy-duty 5-Ply reinforced silicone coupling for strength.

Perfect Fit:
Utilizes the factory mounting locations for a hassle-free installation. The intercooler and tubes utilize billet factory style quick connects to assure a leak-free connection.

Also Fits:
2014-2016 BMW 128i/ix (F20/21) L4-2.0L (turbo) N20
2014-2016 BMW 228i/ix/220i (F22/23) 14-16 L4-2.0L (turbo) N20
2013-2016 BMW 320i/ix (F30/31/34) L4-2.0L (turbo) N20
2012-2016 BMW 328ix (F30) L4-2.0L (turbo) N20
2013-2016 BMW 328i/ix (F31/34) L4-2.0L (turbo) N20
2014-2016 BMW 420i/ix (F32/33) L4-2.0L (turbo) N20
2014-2016 BMW 428i/ix (F32/33/36) L4-2.0L (turbo) N20

Note: This intercooler kit is not CARB exempt at this time and is not legal for sale in California or use on vehicles registered with the California Department of Motor Vehicle.