BMW Performance Intake Kits for BMW 4 Series F32 (2014+)

We are proud to present you with our long-awaited Turner Motorsport Carbon Fiber N55 Intakes. Like all of our Turner Motorsport products, our N55 intake was CAD Designed in-house to give you the best performing, most beautiful intake we could possibly imagine for your N55 powered BMW. The best part? Our design seamlessly integrates with OEM ducting and stock mounting locations to give you a simple install and an OEM+ fit and finish. We believe this is the way the N55 engine bays should have come from the factory. It’s time to ditch all that plastic.

Our higher flow filter and intake design gave our F30 335i an additional 7 WHP and 14 ft-lbs of torque over stock when we tested on our dyno. Our less restrictive intake design reduced post filter pressure by 0.2 psi over stock, allowing for gains across the entire RPM range - this reduced pressure drop also results in less stress on your N55’s turbo. Our enclosed intake also lowers your intake temperatures by 13 degrees over running an open intake.

We offer our N55 carbon intake in either gloss or matte finish, so you can choose what best suits your engine bay. Select either gloss or matte finish below, and then please select whether or not you are purchasing an intake for a manual transmission vehicle. If your vehicle has a manual transmission, it will require BMW Part # 13907515387.

If you are looking for our Turner Motorsport Open Carbon Intake, see T#568168

Download PDF Installation Instructions

Key Features & Benefits:

2x2 twill weave carbon fiber, clear coated for UV protection

Wrinkle Black Powder Coated heat shield

Ovaled Intake tube for OEM quality fitment

High flow cleanable Turner Motorsport air filter

+7 WHP / +14 lb-ft of torque!

Lowers intake temperatures by 13 degrees over running an open intake.

Special care instructions:

If clear coat gets scratched, reseal affected area with clear coat touch up

To retain UV resistance and protect finish, wax with high quality carnuba wax

Our N55 Carbon Intake fits the following BMWs:
2014 - 2016 F22 M235i, M235i xDrive
2012 - 2015 F30 335i, 335i xDrive
2012 - 2015 F32 435i, 435i xDrive

Want more in-depth details? We’ve got you covered below:

Carbon Fiber Intake Lid:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Reduces intake temperatures by 13 degrees compared to running an open intake

Carbon Fiber Intake Tube:

2x2 twill weave carbon fiber, protected by a clear coat for UV protection

Ovaled intake tube design allowing

MAF scaling matches factory intake

MAF sensor flange machined from 6061-T6, black anodized and bonded to the intake tube directly in the center of the tube for accurate temp/airflow reading

Vacuum line port machined from 6061-T6, black andozed and bonded to intake tube

Integrated carbon flange allows secure mounting of intake tube to our heat shield

Heat shield:

One piece design manufactured from 12 gauge 5052 aluminum

Wrinkle black powder coated

Supplied gold heat shield tape

High Flow Air Filter:

Conical high flow cleanable air filer

8 ply oiled cotton gauze

Bellmouth filter flange inlet reduces turbulence and maximizes flow

In BMW's with the N55, the intake system is partially limited. The bottom portion is lightweight and great for feeding cold air to the intake, but the top portion is excessively restrictive. Working with some of the original equipment, this intake continues to utilize the bottom portion of OE ducting and heat shielding, but replaces the top with new high flow ducting and a performance filter. Extensive testing showed up to a 10+ HP gain to the wheels and allows for quicker turbo spool speed. Plus, this design gives you a great sound improvement, letting you hear both the intake and turbo spooling!

Installation and removal is extremely quick and easy, taking only 5 minutes in the driveway!

Features:

• Adds up to 10+ Horsepower
• Dramatic sound improvement
• Super fast install and removal
• Improves throttle response 
• Retains OEM airbox base as a heat shield
• Retains OEM cold air ducting
• Looks great under the hood
• Cleanable and reusable filter
• Made in the USA

BMW B58 Replacement Filter For High Flow Carbon Fiber Intake is designed to enhance the performance of BMW's B58 engine by providing superior filtration and airflow. This high-quality replacement filter is engineered for use with high-flow carbon fiber intakes, ensuring optimal engine performance and longevity.

• Enhanced Airflow: Increases the volume of air entering the engine for improved horsepower and torque.
• Superior Filtration: High-performance filtration media traps contaminants while allowing maximum airflow.
• Durable Construction: Crafted with high-quality materials for long-lasting performance and reliability.
• Easy Maintenance: Designed for straightforward replacement, maintaining the efficiency of your high-flow intake system.
• Perfect Fit: Specifically engineered for the BMW B58 engine, ensuring compatibility and performance.

This replacement filter is a vital component for BMW enthusiasts looking to maximize the efficiency and effectiveness of their high-flow carbon fiber intake systems.

Airflow efficiency and maximizing the potential of the stock intake design were the keys to development for the Dinan N55 intake. Dinan improves on the factory air box system by delivering more cool, dense air. The increased amount of air feeds into dual larger volume airbox complete with a larger cone filter that elicit a slightly more audible and sporty tone over its stock counterpart. Dinan claims 10hp and 15ft-lb torque gain with this kit.

For over 35 years, Dinan has been America's premier tuning company, pioneering advancements in BMW modification while retaining a focus on balanced performance that preserves the original character and driving feel that a BMW offers. When you install a Dinan part on your car, know that it's not only carefully developed and tested, but that Dinan stands behind it with a four year, 50,000-mile warranty. Dinan believes so fully in their “total package” approach that once your car has been fitted with enough of their parts, they celebrate your conversion from stock to Dinan with an exclusive trunk badge, displayed proudly by BMW enthusiasts everywhere. This intake is worth 3 points toward your Dinan badge.

Fitment note: Convertible models require modification to a factory chassis brace. Detailed instructions are included.

This item fits the following BMWs:
2014+ F22 F23 BMW M235i M235iX
2012-2015 F30 BMW 335i 335i X-Drive - Sedan
2012-2016 F32 BMW 435i 435i X-Drive - Coupe
2013-2016 F33 BMW 435i 435i X-Drive - Convertible
2012-2015 F34 BMW 335i 335i X-Drive - Gran Turismo
2012-2016 F36 BMW 435i 435i X-Drive - GranCoupe

Revitalize your BMW's performance with the Dinan Replacement Air Filter designed for Dinan air intake model D760-0038. Whether your filter is dirty, damaged, or lost, this replacement ensures the restoration of Dinan's expected performance and maintains the optimal functioning of your BMW.

For more than 35 years, Dinan has been a leading tuning company in America, specializing in BMW modifications that prioritize balanced performance while preserving the original driving experience. Every Dinan part is meticulously developed, rigorously tested, and backed by a comprehensive four-year, 50,000-mile warranty. Dinan's commitment to a holistic enhancement approach is symbolized by an exclusive trunk badge awarded to enthusiasts who embrace a complete Dinan conversion, showcasing their dedication to elevated performance.

Following in the footsteps of its big brother on the B58 engine, the 4 cylinder intake takes the same path to success. Improve upon the factory design by increasing flow via a larger airbox and filter element thereby improving throttle response and lessening the strain on the turbocharger for maximum efficiency. While box and filter enlargement and redesign is a major factor in ultimately producing a more potent intake they are not the only variables in creating a more efficient design either. The devil is in the details which is where Dinan thrives. Coupled with maintaining Dinan's standard practice of utilizing a sealed system to ensure as much cold, outside air as possible is employed Dinan engineers focused their attention on the intake pipe itself where numerous improvements could be made. In factory configuration, the intake tube comes complete with baffling and a small helmholtz chamber to reduce unwanted sound. As a byproduct, these features also cause a more turbulent air flow path which robs the factory system of potential power. These 2 specific details are diametrically opposed to our intended markets desires so the removal of these features was paramount. Through numerous iterations, a carbon fiber intake tube was developed that eliminated flow disruptions and allowed the natural sound of an unimpeded intake tract to sing. All told this thorough methodology of design allows the Dinan carbon fiber cold air intake for the B46/B48 engine to elicit gains of 6 HP and 6 TRQ at 5000 RPM on a completely stock vehicle. An impressive feat on today's turbocharged engines.

Not to be outdone by the performance side of the equation the B46/B48 intake also is completely made up of carbon fiber unlike 4 cylinder intakes of the past where a mix of materials was used. Not only is the intake completely carbon construction but the quality of the material has been improved over previous generations as well. While looks are surely important, and this piece has that department covered in spades, the improved construction and coating also guarantee that the appearance of the engine bay with the Dinan intake will not be marred over time. Built to present well, perform well, and last the duration, the Dinan B46/B48 carbon fiber cold air intake is a modification that is a must for any high-performance build.

Benefits of the Dinan Carbon Fiber High Flow Air Intake for the F22/F23 230i, F30/F31/F34 330i, and F32/F33/F36 430i:

More Power: +6 HP & +6 lb-ft of torque at 5000 RPM
Sportier Sound
Improved throttle response
Larger volume air box (30% larger than stock) that completely seals
34% increase in filter area (stock: 76.3in², Dinan: 102.1in²)
Optimized carbon fiber intake tube
Free flowing injection molded Air Mass Meter housing (over 20% larger than stock)
Quick and easy installation

HP Gain: +13hp
Trq Gain: +13ft-lbs
Airflow: +28% over stock

aFe has engineered the Momentum GT intake to outperform the stock air box and deliver substantial power and torque gains over the factory system. The B58 3.0L Turbo benefits from aFe's oversized cotton filter element in a Rotomold plastic housing that blocks heat saturated air while flowing more volume of cooler dense air. The system has been CAD designed to achieve the maximum volumetric flow rate into the turbo. The intake tube is a smooth, unobstructed single piece from the air inlet to the airbox and incorporates a port for the air flow sensor. aFe's advanced engineering and design have made this a direct bolt-in intake upgrade.

The aFe filter has been designed specifically for this application and uses aFe's high flow/low maintenance design. The ProDry S filter has an oil-free filter media for less maintenance. For the best flowing filter, with the best performance gain, we always recommend the standard aFe Pro5R filter (which has a blue pre-oiled filter media), but this oil-free filter flows only slightly less than the blue Pro5R style aFe filter, and requires no re-oiling after cleaning the filter.

Features:

• +13 HP and +13 lbs. x ft. Torque max gains
• Outflows factory intake by up to 28%
• High Quality One-Piece Roto-Molded Sealed Housing with Auxiliary Air Scoop
• CAD-Designed Roto-Molded Intake Tube
• Lightweight high gloss, clear-coated 2 x 2 twill-weave carbon fiber trim on housing for styling
• Built-In Sight Window Provides Easy Inspection of Filter Without Disassembly
• Pro 5R oiled 5-Layer Progressively Finer Mesh Cotton Gauze Oiled Media for Maximum Performance
• Unique (Patent Pending) Filter-to-Housing Interface for Easy Installation
• No Cutting or Drilling on factory Parts for Faster Installation

This all new Momentum sealed intake system produced up to 11hp and 15lbs. x ft. torque and outflows the factory intake by 37%. The air filter is housed in a one-piece, patent pending black roto-molded housing that keeps warm engine air out for maximum performance. This unique, one piece, housing with a built in clear sight window allows you to inspect the filter without disassembly. A C.A.D. designed intake tube was engineered to unleash all available horsepower and to fit perfectly. The kit comes complete will all necessary hardware.

Sealed Housing w/ Sight Window: A unique, one piece, sealed housing with a built in clear sight window allows you to inspect the filter with no disassembly.

Housing/Air Filter Interface: This intake system features a unique patent pending filter to housing interface which allows for an easy installation and maximizes filter size.

Horizontal Louvers: The louvers were added to the roto-molded housing to increase the cold air to the air filter.

This part fits the following BMWs:
2012-2015 F30 335ix N55
2013-2015 F31/34 335i/ix N55
2014-2016 F32/36 435i/ix N55
2012-2016 F20/21 M135i/ix N55
2014-2016 F22 M235i N55

7" Tall "Oil Free" Air Filter:
This intake system utilizes an oil free, 7" tall conical 360 degree radial flow performance air filter with 3-layers of synthetic media providing maximum airflow and performance.

High Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Lightweight Vacuum Form Plastic Cover w/ Auxiliary Air Inlet:
Creates a stealthy under-hood look while reducing air intake noise without sacrificing power. A urethane plug is also included if you wish to block off the auxiliary air inlet.

Hassle-Free Installation:
All clamps, coupling and hardware are included for hassle-free installation. This is a direct bolt-on kit that requires no cutting or drilling on factory parts.

DETAILS:

• 350 CFM Rating
• +12 HP / +12 lbs. x ft. Torque max gains
• Outflows factory intake
• CAD-Designed Roto-Molded Intake Tube
• Vacuum Form Cover for Stealthy Under-Hood Look
• Pro DRY S oil-free 3-Layer Synthetic Media for Maximum Convenience With Excellent Filtration Efficiency
• No Cutting or Drilling on Factory Parts for Faster Installation

Note 1:
Does NOT fit Convertible models.

Note 2:
This product is not currently CARB exempt and is not available for sale in California or for use on any vehicle registered with the California Department of Motor Vehicle.

Unique One-Piece High-Quality Housing w/ Auxiliary Inlet:
The smooth one-piece high quality sealed housing with auxiliary air inlet is used to eliminate the use of multiple-piece housings and ensure the coolest air intake charge available. A large, clear sight window is used for a hassle-free filter inspection and an aggressive style. Unique Filter-to-Housing Interface. (US PAT 9440175)

Carbon Fiber Trim On Housing:
This Momentum GT intake system offers carbon fiber trim on the housing to give that motorsport appearance. This cover overlay is constructed of lightweight high gloss, clear-coated 2 x 2 twill-weave carbon fiber.

High-Quality Tube:
This system uses a high quality, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit.

Large 5-Layer Performance Air Filter:
The Momentum GT intake is designed around an oil-free, large 7-1/2" tall inverted top 360-degree radial flow performance air filter with 5-layers of progressive finer mesh cotton media providing maximum airflow and performance. The unique air filter to housing interface (patent pending) allows for maximum filter size which increases the available air volume while simplifying the installation process.

Premium Hardware:
Premium stainless steel clamp is used for strength while also providing the most secure installation available. Momentum intakes are designed with fewer parts for a quick and simple installation.

Note:
This intake system is not CARB exempt at this time and is not legal for sale in California or use on vehicles registered with the California Department of Motor Vehicles.

In BMW's with the B58 engine, the intake system is partially limited. The bottom portion is lightweight and great for feeding cold air to the intake, but the top portion is excessively restrictive. Working with some of the original equipment, this intake continues to utilize the bottom portion of OE ducting and heat shielding, but replaces the top with a new high flow inverted performance cone filter. Extensive testing showed up to a 10+ HP gain to the wheels and allows for quicker turbo spool speed. Plus, this design gives you a great sound improvement, letting you hear both the intake and the turbo spooling!

**B58 Engine - BMW 140 240 340 440 - (B58 Intake)**

Bespoke. A word that perfectly encapsulates the mindset of Eventuri. Performance parts with an obsessive attention to detail and an unyielding dedication to quality. Perfectly designed to maximize the potential of each individual vehicle and meticulously refined through rigorous testing. Eventuri offers a product that stands in a class of its own and delivers outstanding power increases without making false claims or exaggerating dyno numbers. With patented designs such as a custom velocity stack filter housing and improved ducting that guides the flow of air into the engine, to the breathtaking uniformity of the weave pattern. These are performance products for the truly discerning customer.

When it comes to styling a vehicle the proper look is one that compliments, not cheapens the inherent design. Race inspired carbon fiber completes the look and style of every BMW M-powered model and Eventuri delivers on an entirely new level. Instead of simply offering black carbon and yellow kevlar that has become the norm, Eventuri has stepped things up by offering their carbon/kevlar accessories in multiple colors. Now you can choose between Blue, Red, Orange and Yellow weave to further set your ride apart from the pack.

The N55 intake system is a perfect example of Eventuri's “Complete System” principal. It demonstrates the perfect balance between allowing for unrestricted airflow with an open filter housing and cold air saturation with proprietary scoop and duct combination. Every detail has been meticulously developed from the prepreg carbon pieces to the precision bracket work. This intake sets a new benchmark in design and craftsmanship for the N55 platform. 

The Eventuri system uses a Patent Pending Carbon fibre Housing which provides an aerodynamically efficient airflow path from the filter to the MAF tube. Not just another cone filter with a heat shield but a unique design which invokes the Venturi affect.

The filter housing comprises of a high flow filter, aluminium cowl, laser cut bracket and the carbon pod itself. The carbon pod shrouds the reverse mounted filter and smoothly shapes the airflow down to the intake tube. This smooth reduction in cross sectional area invokes the Venturi effect where the airflow accelerates whilst maintaining laminar conditions. It can be thought of as a large velocity stack.

Each intake system includes:

• Prepreg Carbon Fiber Venturi Housing
• High Flow Double Cone Air Filter
• Aluminium Cowl for smooth airflow entry
• Prepreg Carbon Fibre Intake Tube with integrated MAF Sensor Mount
• Prepeg carbon Fibre Air Scoop
• Laser Cut Intake Duct
• Laser Cut Stainless Steel Brackets
• High quality Silicone couplers with BMW specification hose clamps