ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

T#:2206

Part#: 201-6102

Back Ordered

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

Back Ordered

$ 212.99

This product was last offered at the strikethrough price on
04-02-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

19% off MSRP $ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Qty

19% off MSRP

$ 295.92

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP Connecting Rod Bolt Kit - E9X M3 S65

T#:2434

Part#: 201-6001

In Stock

$ 533.99

This product was last offered at the strikethrough price on
02-28-2026

$ 460.99 USD

Add to Wish List

Qty

$ 460.99 USD

Add to Wish List

NEW & REVISED!!! ARP has released a new version of their race-grade M3 connecting rod bolts and its better than ever before. If you're replacing your rod bearings these rod bolts are far superior to standard the OE BMW fasteners in terms of durability and ability to withstand stresses. This set of rod bolts is made specifically for the S65 4.0 liter V8, as found in the 2008-2013 M3 and replaces the previous ARP kit part number RBK_S65.

Show More Show Less

ARP Connecting Rod Bolt Kit for E46 M3, MZ3 (M11 Size)

T#:2211

Part#: 201-6103

Back Ordered

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP Main Stud Kit for M50/M52 and S50/S52 (US)

T#:2208

Part#: 201-5000

In Stock

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP main stud set for the 24 valves M50-based 6 cylinder engines (including M50, M52, S50US and S52US) and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes aerospace quality nuts. The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over. *Does not include washers*

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

BMW M20 Engine ARP Head Stud Kit - E30 325i, E34 525i

T#:189783

Part#: 201-4305

In Stock

$ 271.99

This product was last offered at the strikethrough price on
08-13-2026

$ 271.18 USD

Add to Wish List

Qty

$ 271.18 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1985-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix
1989-1990 E34 BMW 525i

Show More Show Less

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships on Sep 3, 2026

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

VAC Performance Coated Rod Bearing Kit - Standard Size - S65 ...

T#:1061445

Part#: VAC-HPRBK-S65

In Stock

$ 799.99 USD

Add to Wish List

Qty

$ 799.99 USD

Add to Wish List

VAC's S65 bearings are embraced by BMW engine builders world wide. Popular for both forced induction and N/A builds, their coated bearings are "friction resistant" making thermal breakdowns that can occur due to lack of lubrication a much less common occurrence. Helping to prevent premature engine failures on street cars, and spun bearings under stress at the track when things are most critical.

Show More Show Less

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

ARP Connecting Rod Bolt Kit for E36 325 with 53mm Rod Bolt

T#:2186

Part#: 201-6301

In Stock at Vendor

20% off MSRP $ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Qty

20% off MSRP

$ 243.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 53mm length factory BMW rod bolts with part number 11-24-1-713-342 (11241713342) which was used on SOME of the M50 2.5 liter engines from 1992-1995. Check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 44mm rod bolts, you will require kit part# 201-6201 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 53mm rod bolts only ***

Show More Show Less

Part#: VAC-HPRBS-S54

Ships on Sep 1, 2026

$ 479.99 USD

Add to Wish List

Qty

$ 479.99 USD

Add to Wish List

BMW S54 VAC Performance Coated Rod Bearing Kit is highly regarded by BMW engine builders worldwide for its superior quality and performance. Ideal for both forced induction and naturally aspirated builds, these coated bearings are designed to be friction-resistant, reducing the risk of thermal breakdowns due to inadequate lubrication. This feature significantly decreases the chances of premature engine failure in street cars and minimizes the risk of spun bearings during high-stress track conditions.

The VAC Performance Coated Rod Bearing Kit is proven to help maintain engine reliability, even in situations with reduced oil pressure.

Enhanced Durability: Coated bearings are friction-resistant, reducing the risk of thermal breakdown.
Increased Reliability: Helps prevent premature engine failure and spun bearings under stress.
Versatile Performance: Suitable for both forced induction and naturally aspirated engine builds.
Proven Track Record: Tested by customers to ensure reliable performance even with oil pressure loss.

VAC Tech Notes:

Ensure proper tolerance and size checks before installation.
Professional installation is recommended due to specialized tools required.
Returns are not available on any engine bearings.

Show More Show Less

ARP Rod Bolt Kit - S85

T#:1637703

Part#: 201-6002

Ships on Sep 9, 2026

$ 569.99 USD

Add to Wish List

Qty

$ 569.99 USD

Add to Wish List

ARP ARP2000 Head Stud Kit - N55

T#:42335661

Part#: ARP-HSK-N55-S

In Stock

$ 699.99 USD

Add to Wish List

Qty

$ 699.99 USD

Add to Wish List

Enhance your BMW N55 engine's ability to handle higher levels of boost with 5150's custom-designed Head Stud Kit from ARP, the global leader in fastener technology!

ARP Cylinder Head Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105898

Part#: 201-4701

In Stock

20% off MSRP $ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

Qty

20% off MSRP

$ 459.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 367.99 USD

Add to Wish List

For engine builders crafting a high-performance powerhouse, the ARP Cylinder Head Stud Kit is the industry-standard choice for reliability and strength. Each kit features studs, nuts, and washers manufactured from ARP’s proprietary ARP2000 alloy, a material rated far superior to standard aircraft-quality steels.

Show More Show Less

ARP Main Stud Kit for BMW/MINI 1.6 N12/N14/N16/N18 Engine

T#:189787

Part#: 201-5401

In Stock at Vendor

$ 251.99 USD

Add to Wish List

Qty

$ 251.99 USD

Add to Wish List

This ARP main stud set for the new MINI F engines eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each main stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the MINI, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

BMW N54 ARP Head Stud Kit

T#:17538610

Part#: ARP-HSK-N54-14

In Stock

$ 599.99 USD

Add to Wish List

Qty

$ 599.99 USD

Add to Wish List

The VAC Motorsports ARP Head Stud Kit was put together by VAC and ARP’s finest engineers. This is a completely custom kit designed specifically for the almighty N54. *High Boost (25+ psi application) option features: (14) 11mm ARP Head Studs (14) ARP Washers for 11mm Studs (14) ARP Nuts for 11mm Studs Install Tips: MUST drill and tap the (4) 9mm holes in the engine block to make them 11mm holes. This way all the engine block holes are 11mm, and fit ALL (14) 11mm Studs. Torque Specs: All studs torque down through 3-equal steps to 95 ft lbs ***This is NOT the Chrysler and Volvo stud kits! VAC Motorsports and ARP engineers designed and assembled this kit with high grade material, specifically so standard street-use or high-boost N54 owners have a PROPER kit that does not fail over time, such as the retro-fit Chrysler and Volvo head stud kits. ARP is the world leader in fastener technology. Makers of the finest fasteners in the market, especially for BMW engines, ARP is the brand you can count on when you want the highest reliability possible. If you are looking for high performance from your BMW engine, then ARP Head Stud Kits are a must. All kits come complete with hardened parallel-ground washers and aerospace-quality nuts.

Show More Show Less

Main Stud Kit - M50/M52/S50/S52

T#:26171653

Part#: ARP-MSK-M50

Back Ordered

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the M50/M52/S50/S52 engines that were used in a variety of BMW models. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best. Installation Instructions: To ensure accurate torque readings and proper thread engagement, thoroughly clean all threads in the engine block. If necessary, use an ARP chaser to chase the threads. Before installing any hardware, carefully inspect and clean it for defects, shipping damage, and proper fit, length, and dimension. Gently screw the main studs into the engine block by hand until they are snug. Install the main caps, checking for any binding or misalignment. Apply ARP Ultra-torque fastener assembly lubricant to the threads of the studs, nuts, and washers. Install the washers and nuts onto the studs and tighten them by hand. It is highly recommended to use the ARP Ultra-torque fastener assembly lubricant provided with the kit, as it provides consistent clamping force and reduces friction on the studs. Do not use motor oil or other low-quality lubricants. PRELOAD (TORQUE) RECOMMENDATIONS 7. Following the manufacturer-recommended torque sequence tighten the nuts in steps 1-3 Step 1: Tighten to 20 ft-lbs. Step 2: Tighten to 40 ft-lbs. Step 3: Tighten to 60 ft-lbs. With the included ARP Ultra-Torque fastener assembly lubricant

Show More Show Less

ARP Head Stud Kit B48 Undercut CA625+, 12pt

T#:48367044

Part#: 401-4704

Ships on Sep 1, 2026

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

Qty

$ 588.99

This product was last offered at the strikethrough price on
08-13-2026

$ 529.99 USD

Limited Qty Sale

Add to Wish List

MINI 1.6 W10/W11 Engine ARP Head Stud Kit

T#:212677

Part#: 201-4301

In Stock

$ 156.99 USD

Add to Wish List

Qty

$ 156.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following MINIs:
2002-2006 R50 MINI MINI Cooper
2002-2006 R53 MINI MINI Cooper S

Show More Show Less

ARP Main Stud Kit - ARP2000 - BMW B58 3.0L

T#:1105897

Part#: 201-5402

In Stock at Vendor

20% off MSRP $ 292.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 233.99 USD

Add to Wish List

Qty

20% off MSRP

$ 292.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 233.99 USD

Add to Wish List

This ARP main stud set for the 24 valves B58 6 cylinder engines and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design, and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts. Replaces BMW part number 11118604584 The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

Cam Sprocket Bolt Kit for MINI W10 W11 1.6L Engine

T#:26404847

Part#: 206-1001

In Stock

$ 38.99 USD

Add to Wish List

Qty

$ 38.99 USD

Add to Wish List

Enhance the strength and reliability of your Mini's engine with the ARP Main Stud Kit. Engineered to exceed aerospace specifications, these main studs provide superior durability and performance for your engine build. Prevent camshaft flex and ensure optimal torque down for all main caps with ARP's high-quality hardware.

Benefits:

Exceeds aerospace specifications for superior strength
Prevents camshaft flex for improved engine performance
Ensures optimal torque down for all main caps
Complete kit includes main bolts and hardened washers for convenience

Show More Show Less

Pro Series Connecting Rod Bolts N12 N14 N16 N18 1.6L Engine

T#:594611

Part#: 201-6305

In Stock

$ 84.99 USD

Add to Wish List

Qty

$ 84.99 USD

Add to Wish List

Upgrade your MINI Cooper's engine with Pro Series Connecting Rod Bolts designed for N12, N14, N16, and N18 1.6L engines. Crafted from hardened ultra-strength steel by ARP, these rod bolts play a crucial role in maximizing the power output of your engine. Whether you're keeping your MINI stock or pushing it to higher power levels, these bolts ensure sufficient strength and durability for your bottom end.

Hardened ultra-strength steel construction
Compatible with OEM connecting rods or aftermarket options with similar through-bolt fastening
Essential upgrade for maximizing power output and ensuring engine longevity

Show More Show Less

MINI 1.6 N12/N14/N16/N18 Engine ARP Head Stud Kit

T#:189781

Part#: 201-4304

In Stock

$ 227.99 USD

Add to Wish List

Qty

$ 227.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW/MINI head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

Show More Show Less

ARP Head Stud Kit - N63

T#:26238387

Part#: ARP-HSK-N63

Ships in 3 Business Days

Starting at $ 749.99 USD

Add to Wish List

Starting at $ 749.99 USD

Add to Wish List

Upgrade the performance of your BMW N63 engine with our ARP Head Stud Kits, specifically designed for the turbocharged V-8 N63 engine. As you increase the power output of your engine beyond its factory specifications, the head and block may start to separate, causing factory bolts to stretch and fail. Our ARP Head Studs are designed to be stronger than factory bolts, ensuring your race engine stays together even under extreme conditions. Our Custom Age 625+ kit is made from a material with a tensile strength of 260 ksi, substantially higher than the 190 ksi of the ARP 2000 head stud. It's an ideal choice for individuals who want to push the limits of their N63 builds.

Show More Show Less

BMW M62/M62TU Engine ARP Rod Bolt Kit - E39 540i, E38 740i/iL, E53 X5...

T#:189788

Part#: 201-6302

In Stock at Vendor

$ 258.99 USD

Add to Wish List

Qty

$ 258.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the M60 and M62TU. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1997-2003 E39 BMW 540i
1995-2001 E38 BMW 740i 740il
2000-2003 E53 BMW X5 4.4i X5 4.6is

Show More Show Less

ARP Main Stud Kit, BMW S14

T#:28537458

Part#: ARP-MSK-S14

Ships in 3 Business Days

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the S14 B20, S14B23, S14B25, S14B27 engines found in the E30 M3. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best.

Show More Show Less

BMW M50 M52 S50 S52 Shrick Camshaft Set 276 intake / 270 exhaust ...

T#:4731086

Part#: SCH-CSS-S52-276/

Ships in 2 Business Days

$ 2,640.99 USD

Add to Wish List

Qty

$ 2,640.99 USD

Add to Wish List

Elevate your BMW's engine performance with Schrick's premium camshafts, crafted with over 40 years of dedication to excellence. Catering to both street and track enthusiasts, Schrick ensures top-quality materials for strength and accuracy. This renowned brand has formed a lasting bond with BMW enthusiasts, providing advanced camshaft options that have stood the test of time.

Premium Schrick camshafts for BMW
Over 40 years of dedicated engine performance expertise
Ideal for both street and track applications
Top-quality materials for strength and accuracy
Trusted by BMW enthusiasts worldwide
Advanced engine testing and manufacturing technology

Show More Show Less

CP Carrillo Forged Piston Set - BMW M20B25

T#:23847551

Part#: CP-FPS-M20-B25

Ships in 2 Business Days

$ 1,399.99 USD

Add to Wish List

Qty

$ 1,399.99 USD

Add to Wish List

Elevate Your Engine's Performance with Customizable CP Pistons

When it comes to optimizing your engine's performance, flexibility is key. That's why we offer a range of CP pistons with customizable compression ratios to cater to your specific needs. Whether you're embarking on a basic engine rebuild, planning to implement a low boost turbo or supercharger, or aiming to maximize power with high-performance camshafts, we have the ideal piston solution for you.

Our collaboration with CP ensures that you'll receive pistons of the highest quality, meticulously designed to meet the most demanding expectations. These pistons are a top choice for high-performance and racing engines.

We maintain a diverse selection of compression ratios in stock, making it convenient to find the right fit for your project. And if you require a custom piston application, our efficient service has you covered.

BORE: 84mm
Rod Length: 135mm
Compression Ratio: 8.5:1

Show More Show Less

HEAD STUD KIT - BMW S85

T#:20089537

Part#: ARP-HSK-S85

Ships in 5 Business Days

$ 579.99 USD

Add to Wish List

Qty

$ 579.99 USD

Add to Wish List

ARP Cylinder Head Stud Kit - Custom Age 625+ - BMW S63 4.4L

T#:51110152

Part#: 201-4703

Ships in 8 Business Days

$ 1,099.99 USD

Add to Wish List

Qty

$ 1,099.99 USD

Add to Wish List

For engine builders pushing the absolute limits of high-performance engineering, the ARP Custom Age 625+ Cylinder Head Stud Kit represents the pinnacle of fastening technology. While standard aircraft-quality steels and even the renowned ARP2000 alloy are impressive, the proprietary Custom Age 625+ super-alloy provides a massive leap in capability by increasing tensile strength by an additional 40,000 to 60,000 psi. This specialized hardware is engineered specifically for ultra-high-boost applications, offering superior fatigue resistance and the unique ability to maintain its structural integrity under extreme temperatures that would cause lesser materials to weaken.

Show More Show Less

BMW M10 Engine ARP Head Stud Kit - 2002, E21 320i, E30 318i

T#:189784

Part#: 201-4601

Ships in 8 Business Days

$ 196.99 USD

Add to Wish List

Qty

$ 196.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found and we highly recommend them in both racing and forced induction applications. Due to the additional clamping force between the head and block, these are IDEAL for turbocharged engines.

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set.

This item fits the following BMWs:
1970-1976 2002 BMW 1600 2002 2002tii
1977-1983 E21 BMW 320i
1984-1985 E30 BMW 318i

Show More Show Less

JE Pistons Forged Piston Set - 84mm - 10.5:1 - M52

T#:11857228

Part#: JE-FPS-M52-84-10

Ships on Sep 1, 2026

$ 1,439.99 USD

Add to Wish List

Qty

$ 1,439.99 USD

Add to Wish List

Boost Your BMW's Engine with JE Pistons

Upgrade your BMW's engine with the JE Pistons Forged Piston Set designed for the M52 engine. These high-quality forged pistons feature a diameter of 84mm and a compression ratio of 10.5:1, ensuring improved performance and reliability for your BMW.

Enhances engine performance and reliability
Precision-engineered for optimal fit and function
High-quality forged construction ensures durability
Designed specifically for the M52 engine

Show More Show Less

ARP Rod Bolt Set - M20 - 53mm

T#:1061435

Part#: ARP-RBS-M20

Ships on Sep 1, 2026

$ 314.99 USD

Add to Wish List

Qty

$ 314.99 USD

Add to Wish List

ARP, the world’s leader in fastener technology. There is no substitute for the best! Planning to boost your M20? Building a high HP stroker engine? This rod bolt kit is for you! This kit provides higher strength, more clamping power, and the option to re-use the hardware unlike your OEM bolts. We run these in many of our own builds as well and are 110% satisfied with the fit and finish of these ARP bolts. We offer a 53mm UHL version for those running OEM M20 rods or a 44mm UHL version for those who have upgraded to S50/S52 OEM rods.

Show More Show Less

ARP Connecting Rod Bolt Kit - M10 1.8L

T#:554123

Part#: 201-6304

Ships on Sep 1, 2026

$ 119.99 USD

Add to Wish List

Qty

$ 119.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMW Engines:
M10 1.8L

Show More Show Less

VAC Motorsports Performance Coated Rod Bearing Set - BMW E30 M3 S14 ...

T#:638307

Part#: VAC-HPRBS-S14STD

Ships on Sep 1, 2026

$ 249.99 USD

Add to Wish List

Qty

$ 249.99 USD

Add to Wish List

VAC Rod Bearing Sets are specially coated to reduce friction to a minimum; enabling lower temps and faster revolutions in your expensive S14 engine. The coated bearings are thermal breakdown resistant, helping to prevent premature engine failures under stress when things are most critical. The rod bearing area is a common stress area in the S14, these bearings can last much longer than any normal bearing sets and are used in all of VAC's highest performance BMW engine builds. These bearings have become a favorite product of all of VAC's race and engine building customers around the globe who have reported unparalleled wear characteristics under all conditions. Made for VAC by the same company who manufactures for the US military, NASCAR teams, and other customers that require "mission-critical" quality. If you are looking for high-performance rod bearings, this is the set for your S14. VAC Tech Notes: As with all bearings, please check your tolerances and size before installation. Due to the specialized tools needed, professional install recommended. There are no returns available on any engine bearings.

Show More Show Less

Pro Series Connecting Rod Bolts

T#:31556195

Part#: 206-6008

In Stock

$ 74.99 USD

Add to Wish List

Qty

$ 74.99 USD

Add to Wish List

ARP Ultra-Torque Fastener Assembly Lubricant (Select Your Size) ...

T#:338571

Part#: TMS1733

In Stock

Starting at $ 1.99 USD

Add to Wish List

Starting at $ 1.99 USD

Add to Wish List

If you are using a premium fastener, such as the ARP brand rod bolts, head bolts, or main bolts, then you will want this assembly lube. Made to be used to precisely duplicate all ARP fastener preload specifications.

Show More Show Less

Pro Series Head Bolts W10 W11 1.6L Engine

T#:26404879

Part#: 206-3601

Ships in 2 Business Days

$ 131.99 USD

Add to Wish List

Qty

$ 131.99 USD

Add to Wish List

Enhance the performance of your Mini with ARP's Pro series cylinder head bolts. These bolts are cold-forged for maximum molecular integrity and heat-treated to withstand extreme pressure, rated at 190,000 psi. Featuring 12-point heads, each kit includes hardened parallel washers for precise torque readings and even load distribution.

Cold-forged for maximum molecular integrity
Heat-treated to withstand extreme pressure
Rated at 190,000 psi for exceptional strength
12-point heads for easy installation
Includes hardened parallel washers for precise torque readings

Show More Show Less

ARP Head Stud Kit - S63

T#:26238368

Part#: ARP-HSK-S63

Ships in 3 Business Days

Starting at $ 749.99 USD

Add to Wish List

Starting at $ 749.99 USD

Add to Wish List

With 5150's ARP head stud kit, you can securely tune up the boost on your BMW S63 engine without worrying about the cylinder heads lifting. Specifically designed for the turbocharged V-8 S63 engines found in high-performance models such as F10 M5, F90 M5, F12 M6, F95 X5M, F96 X6M and F13 M6. 201-4702, 201-4703. As you increase the power output of your engine beyond its factory specifications, the head and block may start to separate, causing factory bolts to stretch and fail. Our ARP Head Studs are designed to be stronger than factory bolts, ensuring your race engine stays together even under extreme conditions. Our Custom Age 625+ kit is made from a material with a tensile strength of 260 ksi, substantially higher than the 190 ksi of the ARP 2000 head stud. It's an ideal choice for individuals who want to push the limits of their S63 builds. ARP S63 Head Stud Kit for: M5 F10 2011-2016 M5 F90 2017 M6 F13 2011-2018 X5M F95 2013-2018 X6M F96 2014-2019 ARP2000 Step 1: Tighten to 30 ft-lbs. Step 2: Tighten to 60 ft-lbs. Step 3: Tighten to 90 ft-lbs. Custom Age 625+ Step 1: Tighten to 30 ft-lbs. Step 2: Tighten to 60 ft-lbs. Step 3: Tighten to 110 ft-lbs.

Show More Show Less

ARP Head Stud Kit, BMW S14

T#:28537451

Part#: ARP-HSK-S14

Ships in 3 Business Days

$ 179.99 USD

Add to Wish List

Qty

$ 179.99 USD

Add to Wish List

This ARP head stud Kit is designed for the BMW S14 B20, S14B23, S14B25, S14B27 engines found in the E30 M3. Installing ARP head studs can provide several benefits, including increased clamping force, improved head gasket sealing, and greater overall engine strength. This is especially important in high-performance and racing applications where the engine is subjected to increased stress and higher temperatures. Before installing ARP head studs, it is important to properly clean and prepare the engine block and cylinder head mating surfaces. It is also recommended to use ARP Ultra-Torque Fastener Assembly Lubricant during installation to ensure proper torque and clamping force. Instructions: 1. To ensure proper thread engagement and accurate torque readings, clean ALL threads in the block. Chase if necessary with ARP Thread Chaser. 2. Clean and inspect all hardware prior to installation. Look for obvious defects or shipping damages, plus proper fit, length and dimension. 3. If the cylinder head studs protrude into a water jacket, lubricate the block threads of the studs with ARP THREAD SEALER. 4. Screw studs into the block “HAND TIGHT ONLY”. 5. Install the cylinder head(s) and check for binding or misalignment. 6. Lubricate the stud threads, nuts and washers with ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT. Then install the washers and the nuts onto the studs and tighten them hand tight. ARP recommends using the ARP ULTRA-TORQUE FASTENER ASSEMBLY LUBRICANT that is provided with each kit as opposed to motor oil. This is due to higher friction on the studs as well as inconsistencies in the clamping force of the fasteners when motor oil or other low quality lubricants are used.

Show More Show Less

ARP Cylinder Head Stud Kit - Custom Age 625+ - BMW B58 3.0L

T#:47610654

Part#: 401-4701

Ships on Sep 1, 2026

20% off MSRP $ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

Qty

20% off MSRP

$ 1,027.99

MSRP stands for Manufacturer's Suggested Retail Price. This is the suggested retail price provided by the manufacturer, supplier or seller.

$ 822.99 USD

Add to Wish List

For engine builders pushing the absolute limits of high-performance engineering, the ARP Custom Age 625+ Cylinder Head Stud Kit represents the pinnacle of fastening technology. While standard aircraft-quality steels and even the renowned ARP2000 alloy are impressive, the proprietary Custom Age 625+ super-alloy provides a massive leap in capability by increasing tensile strength by an additional 40,000 to 60,000 psi. This specialized hardware is engineered specifically for ultra-high-boost applications, offering superior fatigue resistance and the unique ability to maintain its structural integrity under extreme temperatures that would cause lesser materials to weaken.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts

Sub-Categories

Benefits:

Elevate Your Engine's Performance with Customizable CP Pistons

Boost Your BMW's Engine with JE Pistons

Select Vehicle

Category

Brand

Price

Special Offers

Shipping

Narrow Results