Top Schwaben Tools For Your BMW

Adapts the Schwaben by Foxwell scan too to work on cars with 20 pin under hood connectors. If you're a fan of older model BMW's and still want a more advanced diagnostic tool or to be able to reset your service lights, this is the ultimate accessory for your new scan tool. Perfect for pre- OBDII vehicles that require the use of the diagnostic port in the engine bay.

For models produced from 1987-2002 with 20 pin diagnostic socket under hood.Schwaben By Foxwell Professional Scan Tool For Most BMWs and MINI coopers

For use with the Schwaben Professional BMW/MINI Scan Tool

Schwaben offers the right tools to make your next project a success. Everything from complex engine scanners to brake bleeders and spring compressors, Schwaben tools has you covered.

Some of the recommended use include but are not limited to:

• Remove and install rear ball joints on E38, E39, E60/61, E63/64, E65/66, and E70's
• Removal and installation of ball joints and bushings on rear control arms on E36, E46, E39, E60/61, E63/64,  E65/66, E70, E83 and E85/86 Z4's
• Removal and installation of rear sub frame mounted differential bushings on E36, E46, E83 and E85/86 Z4's
• Removal and installation of rear differential mounted bushings on E36, E46, E9X, E60/61, E63/64, E65/66, and E85/86 Z4's

This hand held Schwaben tool makes changing fluids an easy, quick task.The Schwaben fluid suction/fill pump suitable for oils, water and any non corrosive liquid.

Features 

• Comes with a flexible and a rigid tube. 
• Flow rate is adjustable for different functions.
• 350 ML capacity
• Cylinder is marked in 20 mL increments and fraction of quarts for accurate filling. 

Not for use with gasoline.

When doing work where the mounts and support need to be removed from the engine or transmission having a engine support bar is wise. By using this engine support the stress is coming off of whatever components are still attached reducing future unnecessary repairs. The safety side of it is having the heavy engine and transmission firmly supported as it should be instead of questionable jack techniques.  

Features:

•  2" longer than most
•  Two angle chain hooks for safer and more stable chain support 
•  61" long and fully adjustable to any width
•  Weight rating is a full 1000 lbs.
•  Includes four rubber padded feet to prevent slipping and damage to cars finish 
• This tool features a dual hook design for holding engine or transmission in place
•  Powder coated for long life and durability

Note: It is important that chains are hooked to both sides of hook, like in photo to insure load is supported evenly. 

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

Specially designed to be stronger than alternatives on the market, this jack pad adapter makes the vehicle lifting procedure faster, safer, and easier than ever before. Simply remove the rocker jack point access plug, fully insert the Schwaben Jack Pad Adapter, and lift securely using your hydraulic floor jack.

Features:

• Heat treated 4140 high strength steel
• Fully seam welded 70mm jacking plate
• Exact-fit profile for limited movement in vehicle
• Black zinc coated for corrosion resistance
• Long shaft to position jack plate away from the body for adequate jack clearance

Note: Always secure your vehicle on jack stands. Never rely on a floor jack alone.

Many BMWs, especially older models, feature pinch welds where the floor pan meets the rocker. These run from wheel-well-to-wheel-well and are an especially appealing jacking location with one shortfall - jacking on an unprotected pinch weld will frequently cause an unsightly bent and damaged weld. This damage is a quick to rust spot, being located on the lowest point of the vehicle and no longer being covered by protective ecoat, paint, or undercoat.

This Schwaben Pinch Weld Protector is designed to fit between any floor jack cradle and bottom of vehicle. It features a specially designed slot to straddle pinch welds, keeping jack from crushing or bending the pinch weld. The bottom side of protector is designed to fit any jack as well as the Schwaben (T#363164) aluminum jack stands. 

Extruded and designed in USA. Pad is 3" wide & 1" tall.

The BMW M60 and M62 engines found in many 5 series, 7 series, and X5's has two major weak points over time - Vanos seal and timing guides. The timing guides, being the most noticeable and damaging, can be very expensive to have a shop repair when trying to get back on the road. If you have some mechanic abilities and can follow instructions you could get this job done for a lot less, but you'll need the right tools for the job. 

This Schwaben kit features everything you need in one case to perform either job or both making timing service easy and accurate.

Never worry about buying another M60 or M62 timing tool kit again with our LIFETIME REPLACEMENT program - included with your purchase!

Tools included:

• Camshaft locking blocks
• Flywheel locking pin
• Timing chain tension block
• Upper chain tension locks
• Timing wheel alignment tools
• Vanos adjustment socket
• Vanos solenoid socket

This gauge ensures that the inlet and exhaust cams are aligned perfectly. Make sure the edges are on the correct sides of the cylinder head before using.

Includes two alignment pin's which is ideal for inspection and servicing the motor with the timing chain still attached. If you are going to be removing the timing chain for service, you will need to lock both cams. 

The Ultimate kit includes every thing the standard kit does along with, a second alignment bridge, flywheel lock pin, VANOS alignment tools. and 4 bolt crank socket.

This tool fits all S54 powered BMW, including: 
2001-2006 E46 BMW M3
2001-2002 E36/7 BMW Z3M Coupe Z3M Roadster
2006-2008 E85/6 BMW Z4M Coupe Z4M Roadster
 

Featuring a T60 Torx head, the belt tensioner found on the N54/N55 engine has exceptionally tight quarters. Use of this tool will allow access to the lock pin hole without excessive component removal, making belt removal and installation a much easier task.

This tool fits all N54/N55 powered BMW, including: 
2008+ E82 BMW 135i 1M Coupe 
2014+ F22 BMW M235i 
2006+ E90 BMW 335i 335xi 335i xDrive - Sedan 
2007+ E92 BMW 335i 335is 335xi 335i xDrive - Coupe 
2007+ E93 BMW 335i - Convertible 
2012+ F30 BMW 335i 335i xDrive - Sedan 
2013+ F32 BMW 435i 435i xDrive - Coupe 
2014+ F34 BMW 335i xDrive GT - Gran Tourismo 
2015+ F80 BMW M3 - Sedan 
2015+ F82 BMW M4 - Coupe 
2015+ F83 BMW M4 - Convertible 
2006-2010 E60 BMW 535i 535xi 535i xDrive 
2010+ F07 BMW 535i GT, 535i xDrive GT 
2011+ F10 BMW 535i 535i xDrive 
2012+ F13 BMW 640i 
2009+ F01 BMW 740i 740li 
2011+ F25 BMW X3 xDrive35i 
2007-2013 E70 BMW X5 xDrive35i 
2007-2014 E71 BMW X6 xDrive35i 
2009+ Z4 BMW Z4 sDrive35i Z4 sDrive35is 

Plastic five-piece tool kit removes trim and door panels, moldings, and adhesive backed logos and badges, without damage. By using a non-marring plastic you can safely and easily remove trip pieces with confidence

Features:

• Pull-type remover

• Narrow edge remover

• Wide edge remover

• Handle remover

• Upholstery clip remover

Our aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

Better still, order two: one for your garage and another for the emergency tool kit in you trunk.

To secure shocks and struts to their mounts, the retaining nut must be torqued to its proper specification using a torque wrench. An improper torque value may result in premature mount failure - or worse. Strut nut sockets allow for the use of an allen wrench to hold the damper shaft while utilizing your 1/2" drive torque wrench on the socket to achieve proper torque.

Kit Features:

• 18mm
• 19mm
• 21mm
• 22mm
• 24mm

This professional-grade fender roller allows you to gently and gradually flatten your inner fender lips in order to increase your fender to tire clearance.

This is the perfect tool for:

• If you want to lower your vehicle
• If you want wider-than-stock wheels
• If you are going to use wheel spacers or decreased offset

By rolling the fender lip flat, you can lower your car further, and give your car a wider stance, without your tires rubbing on the inside of the fender.

Fully adjustable for use on vehicles of different ride heights, offsets, and wheel bolt patterns. Fits 4 and 5 lug hubs with up to 120.6mm (4.75") bolt patterns.

Works on up to 0.507in./13mm studs

Cars with larger 14mm studs require enlarging slots to 14mm 

Use of a heat gun is recommended to soften the fender surface during the rolling process and prevent paint cracking.

The perfect kit containing most of your needed European essentials. 

Features:

• 13PCS-1/4" DR.6PT SOCKETS: 4, 4.5 , 5 ,5.5 ,6 , 7, 8 ,9 ,10, 11, 12, 13, 14MM 
• 1PC- 1/4" DR. QUICK RELEASE RATCHET (72T).
• 2PC- 1/4" DR.50 & 100MM EXTENSIONS 
• 1PC- 1/4" DR.150MM FLEXIBLE EXTENSION
• 1PC- 1/4" DR.UNIVERSAL JOINT
• 1PC- 1/4" DR.SLIDING T-BAR
• 1PC- 1/4" DR.6" SPINNER HANDLE
• 1PC- 1/4" DR.1/4" BIT HOLDER ADAPTER
• 4PCS-HEX KEY WRENCHES:1.27, 1.5,2,2.5MM
• 6PCS-1/4" HEX SOCKETS:3,4,5,6,7,8MM
• 3PCS-1/4' SLOTTED SOCKETS:4,5.5,7MM
• 3PCS-1/4" PHILIPS SOCKETS:PH1, PH2, PH3
• 3PCS-1/4"POZI SOCKETS: PZ1, PZ2, PZ3
• 6PCS-1/4" TORX SOCKETS: T10, T15, T20, T25, T30, T40

Own an E30? This tool kit is a perfect fit for your glovebox!

Having a creeper can make working under the car much easier and more comfortable, roll in and out, padding, and keeping those clothes a bit cleaner. 

 Features:

• Thick fully padded leatherette cover.
• 40" long with heavy-duty metal support frame.
• 1"" steel tube frame.
• Four position adjustable headrest.
•  Six 2 1/2"oil-resistant rollers.
• Powder coated frame to resist rusting.
• Overall dimensions: 17" x 40" X 4"
• Ground clearance: 1-1/2"
• Ball bearing swivels on wheels.
• 250lb capacity.

The Schwaben aluminum wheel hanger makes it easy to remove and install wheels. Just thread the hanger stud into a wheel bolt hole and hang the wheel safely while you rotate tires or remove them for service or vehicle repair. (It's also great for keeping wheel bolt holes aligned on cars with spacers.)

Features:

• Longer & Lighter
• Made of 6061-T6 aluminum
• Anodized for hardness and good looks
• Knurled, non-slip handle has a drilled hole so you can hang it on a pegboard hook in your garage

As any mechanic either at home or in a shop knows, there is rarely enough usable floor space. At least with a wall mounted tire rack you can count on the spare tires to be out of your way. Space is not the only factor for choosing a wheel storage product like this, most people don't realize that a concrete floor actually draws moisture leaving your tires to dryout even faster.

Features:

• Adjustable links allow you to store any size from 12" wheels to 19" wheels with tires
• Folds flat against the wall when not in use to maximize your usable space
• Supports up to 250 lbs and weighing in at only 20 lbs itself
  
• 46" wide storage area (holds up to four 11½" wide tires)
• Sturdy steel construction
• Mounting holes spaced 48" apart for mounting to standard center studs

Now you can stack your extra wheels without the danger of scratches and scuffs. This wheel storage rack keeps your wheels spaced apart, and being on locking casters, allows you to easily move the whole set anywhere in your garage or shop at one time. Sturdy steel construction and a wide base means this wheel rack won't tip over. Holds up to 275 lbs - enough for most any wheel & tire set.

Fits up to 8½" wide wheels, depending on offset

 The 15" long head features 60 super bright LED's. 51  LED's light up the wide side view and 9 LED's on the end for  more of a flashlight mode. Featuring a drop-down design to keep the light handy when you need it, but out of the way when you don't. 

Features:

• 120 Lumens 
• 30 ft. Cord
• Fully adjustable position stop
• Hooked end 

This high quality LED flashlight can fit in the palm of your hand and  throw a super bright beam of light over a great distance. Equipped  with a CREE high power LED for optimal light output. LED is very energy efficient and can last  for up to 50,000 hrs. The large 1.5 in. reflector is excellent for maximun distance.

Features: 

• High Output, high quality 3-Watt CREE LED lamp.
• Tail cap push button has three different switch settings, 300 Lumen, 150 Lumen and off.
• Durable Rigid aluminum alloy case.
• Anti roll hex shaped design head.
• O-ring sealed, water resistant.
• Battery life up to 10 hrs.
• Complete with wrist lanyard.
• Includes 3 AAA batteries. 
• Head diameter  1.5 in., Overall length 5.5 in., Body diameter 1 in.

Custom exhaust work in the plans? The Schwaben Exhaust Pipe Cutter will help you cut out old pipe or cut down new pipe with ease. It can cut any pipes from 3/4" to 3" in diameter and cuts pipe with only 1/4 turn adjustments, thanks to 15 blades that effectively cut the entire pipe with little movement. This is great for tight to reach places that prevents you from using more traditional non-specialty tools.

Features:

• Cuts from 3/4" pipe up to 3" pipe
• 15 cutting blades
• Rubber covered handles for grip and comfort

This great Schwaben kit is designed to work on todays modern cars. Set contains popular torx and triple square bits found on a lot of German and other European cars. Designed to operate in minimal space situations.

Set Contains:

• 6 stubby triple square with 12 mm hex to be used with included 12 mm ratcheting wrench. 4 mm, 5 mm, 6 mm, 8 mm and 10 mm. 
• 4 stubby triple square with 19 mm hex to be used with included 19 mm ratcheting wrench.. 12 mm regular and  14 mm, 16 mm and 18mm tamper proof triple square.
• Set also includes a 3/8" drive 12 mm socket and 1/2" drive 19 mm socket to fit bits. Good for using bit with ratchet or torque wrench.
• 9 torx bits 10 to 70 torx 
• Includes blow molded case with sturdy foam insert to keep every thing in order.

All the right bits in one box. The perfect assortment to keep the job going.

Features:

• 10 fractional SAE hex, 9 Torx® tamper-proof, 9 Torx®

• 9 Metric hex bits, 9 slotted bits, 8 Pozi-drive, 8 Phillips, 4 square-recess, 4 tri-wing

• 3 spline, 3 Torq, 3 clutch, wing-nut driver, magnetic bit holder and socket bit holder

• Made of hardened Chrome Vanadium steel for years of dependable use

• Packaged in a handy blow molded case with individually marked bit slots for easy organization

A satin chrome finish with a knurled ring around socket body, the knurling allows for a better grip when hands and sockets are covered in oil or grease. All sockets feature a radius in the corners for superior torque to the sides of the fastener, not the corner. Complete size coverage.

Features:

• 8mm, 9mm, 10mm, 11mm, 12mm, 13mm, 14mm,
•  15mm, 16mm, 17mm, 18mm, 19mm
• Limited Lifetime Warranty