Vehicle Lifts, Jacks, and Ramps for BMW 7 Series E32 (1988-1994)

Here's what makes this floor jack the best on the market:

• Dual pump pistons to reach maximum height in 5 pumps
• Low profile design keeping lowered cars in mind
• Easy maneuverability 
• Two piece quick release padded handle for storage or transport.

Details:

• Jack Capacity 2 Ton
• Max Lift Height 20"
• Low Height 3.25"
• Chassis Length 26.5"
• Overall Width 13"
• Saddle Diameter 4.5"
• Handle Length 50"
• Shipping Weight 50 lbs

Due to clearance issues, many types of lifts require specific adapters that are made for reaching SUV and truck jack points. This 12-piece kit has been made by using stackable adapters that mount inside the lifting block trays so that vehicles with high ground-clearance or those with unique jack point locations are better accommodated. These adapters offer up to 7.2" of additional height when all combined.

Complete kit includes:

• Low‐profile round polyurethane contact pads  -  Qty: 4
• Sliding receivers that accommodate the round polyurethane contact pads and/or the stackable adapters  -  Qty: 4
• 3" stackable adapters.  -  Qty: 4

Fits BL-5000SLX/EXT and BL-7000SLX/EXT Series Only.

Male & female quick-connect fittings conveniently connect the leader hoses to the long hoses, making it easy to assemble and disassemble QuickJack after the simple one-time setup.

Each flush-face, zero-leak fitting is designed to prevent hydraulic oil or ATF from leaking, ensuring your frames function properly at all times.

Male fitting does NOT attach to QuickJack power unit.

Compatible with all SLX and TL models.

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 6.5" long x 1.5" tall x 4" wide

Urethane Pinch-Weld Block - Set provides a superior solution for supporting vehicles on pinch-weld rails. Traditional rubber blocks can cause damage to delicate body rails due to excessive pressure points. These urethane pinch-weld blocks are engineered with a cross-cut slotted design, allowing versatile positioning either lengthwise or crosswise. They are ideal for safely supporting rocker panels or sheet metal body rails, particularly those that have degraded from corrosion over time.

• Specially formulated urethane rubber for durability
• Deep bilateral slots accommodate virtually all pinch weld frames
• Versatile positioning: lengthwise or crosswise
• Water, chemical resistant, and 100% weatherproof
• Single-piece construction ensures a superior hold
• Dimensions: 3.9” (L) x 2.9” (W) x 2.4” (H)

These QuickJack rubber contact blocks are used with all QuickJack systems and can be used with other QuickJack pads or are perfect to replace missing pads. If the blocks included with the QuickJack lift system have a hard time reaching the jack points of the vehicle, these can be used to help properly reach and support the vehicle on the lift.

These blocks are made of a hardened rubber that has specifically been formulated to resist gouging, cutting, and abrasion. They are also resilient against chemicals and solvents that would normally damage rubber.

Dimensions: 4" long x 2" tall x 3" wide

Many BMWs, especially older models, feature pinch welds where the floor pan meets the rocker. These run from wheel-well-to-wheel-well and are an especially appealing jacking location with one shortfall - jacking on an unprotected pinch weld will frequently cause an unsightly bent and damaged weld. This damage is a quick to rust spot, being located on the lowest point of the vehicle and no longer being covered by protective ecoat, paint, or undercoat.

This Schwaben Pinch Weld Protector is designed to fit between any floor jack cradle and bottom of vehicle. It features a specially designed slot to straddle pinch welds, keeping jack from crushing or bending the pinch weld. The bottom side of protector is designed to fit any jack as well as the Schwaben (T#363164) aluminum jack stands. 

Extruded and designed in USA. Pad is 3" wide & 1" tall.

Ensure safe and professional jacking of your BMW, 2020 Supra, or MINI with the Turner Motorsport Jack Pad Adapter. Designed to mimic the factory scissor jack, this adapter allows for secure lifting at any of the 4 factory jack points without causing damage to your vehicle. Made in the USA from solid billet aluminum, it features the Burger Motorsports logo and a honeycomb grip pattern for stability. Simple to use and compatible with most floor jacks, it ensures correct and secure lifting every time. Here are the key benefits:

• Safely lifts your BMW, 2020 Supra, or MINI at factory jack points
• Prevents damage to rocker panels or vehicle undercarriage
• Made from solid billet aluminum for durability
• Engraved Burger Motorsports logo for authenticity
• Honeycomb grip pattern for stability during use