Turner Motorsport BMW Suspension Parts for BMW E36 (1992-1998) M3

Our sealed Monoball Rear Trailing Arm Bushings (RTAB) are the best solution for completely eliminating deflection and unwanted toe changes on the rear of the E36, E46, and Z4. While rubber and urethane bushings flex during load, the toe can change widely giving you nervous and unpredictable handling. These RTABs have a solid aluminum housing with a high-quality sealed OE bearing. These bushings were developed from years of competition use in various racing and HPDE events. There is simply no better RTAB unless your racing class rules prohibit the use of mono or spherical bearings.

The rear trailing arm bushings take a lot of abuse from acclerating, braking and cornering. The stock rubber bushings are just not up to the task of keeping rear wheel alignment in spec for very long, especially if you have upgraded to stickier tires and a better suspension. The pliable rubber flexes and twists which slows down reaction time and leaves you with a car that feels nervous and 'tail happy'. Urethane helps to control the alignment but issues with fitment, maintenance, and longevity keep us from recommending urethane on anything but a street car. We also offer a Delrin RTAB for cars that must conform to certain racing class rules. These sealed spherical bearings are the best at controlling rear toe alignment.

Our aluminum RTABs are very well made - high grade aluminum alloy and steel CNC'd out of a billet by an ISO 9001 certified manufacturer, each component is either hardcoated or nickel plated. While multiple manufacturers offer two piece designs, our research showed that a one piece bushing is a better design featuring a sealed bearing to keep contaminants out extending the life of the bearing.

Features:

Key Benefits:

• Rear Trailing Arm Monoball eliminates unwanted deflection, maintaining alignment settings and minimizing wheel hop.
• Allows full rear trailing arm articulation for low friction movement and eliminates binding found in rubber and poly bushings.
• Completely streetable: utilizes an OES Lemforder brand sealed, greased ball joint for an extremely long service life with no increase to NVH.

Design Features:

• Housing: Billet CNC 6061-T6 aluminum, type II anodized for exceptional durability and corrosion resistance
• Bearing: OE Mercedes/lemforder 2043520027 Sealed ball joint
• Bearing inserts: CNC machined 303 stainless steel.
• Rebuildable

Clickhere for installation instructions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Whether you need a camber change or you are looking for more adjustment with your camber plates, you can change your camber by shimming the strut and spindle with the TMS bolt kit. There are some things to take into account with this kit so please read the installation tips below. An alignment is strongly recommended after installing this kit.

Click here for installation instuctions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe
2006-2008 E85 E86 BMW Z4 M Roadster M Coupe

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle.

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.

These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.

Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
 

TMS Part#Center to Center (mm)Center to Center (inch)

TSU9912A35155.00mm - 170.00mm6.10" - 6.69"

TSU9912A40170.00mm - 185.00mm6.69" - 7.28"

TSU9912A45180.00mm - 195.00mm7.08" - 7.67"

TSU9912A50190.00mm - 205.00mm7.48" - 8.07"

TSU9912A55207.00mm - 222.00mm8.15" - 8.74"

TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"

TSU9912A70240.00mm - 255.00mm9.45" - 10.04"

TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"

TSU9912A80261.00mm - 276.00mm10.28" - 10.87"

TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"

TSU9912A95290.00mm - 305.00mm11.42" - 12.00"

TSU9912110320.00mm - 335.00mm12.59" - 13.19"

TSU9912115330.00mm - 345.00mm12.99" - 13.58"

TSU9912130362.00mm - 377.00mm14.25" - 14.84"

TSU9912135370.00mm - 385.00mm14.57" - 15.16"

TSU9912140381.00mm - 396.00mm15.00" - 15.60"

TSU9912145389.00mm - 404.00mm15.31" - 15.91"

Please select your length below. 

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should. 

Increasing the negative camber of your E36 M3 will reduce understeer and prolong the life of your tires when used on the track. These plates simply bolt on top of the factory upper strut bearings and increase negative camber by .5 or 2 degrees, depending on the holes you chose to use. We maximized the available camber available with a stock-diameter sized spring. Vehicle height in the front will be raised by .25”. We also added material to the surface area of the mount to increase stiffness of contact area, therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal for many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class. 

This item fits the following BMWs: 
1996-1999 E36 BMW M3 
1998-2002 E36/7 BMW Z3 M Coupe M Roadster

These bushings have the hole off-center to give your car a little more track, caster, and camber. This style came as standard equipment on E30 M3s (8/89-later) and 1995 E36 M3 but will work with any E30, E36, Z3.

Rubber control arm bushings are designed to flex and absorb energy. That's fine on a streetcar but on an all-out racing machine you want your alignment to stay constant. We have picked Delrin for this application due to its high rigidity and low coefficient of friction allowing for minimal suspension bushing deflection (geometry change) but decreasing bushing windup or drag (friction). They are not recommended for street-use but highly-recommended for track cars.

To save time, pick up a pair of new bushing carrier brackets and hardware. This will save you the time and hassle of pressing out the old bushings. This will especially save you time if you're buying new control arms at the same time (no time wasted removing the old brackets from the arms). Stainless steel set screws included.

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle. 

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

Here at Turner we understand the importance of an upgrade that will get the results you need on the track and still be tolerable on the drive around town. When it comes to control arms on the track, making them as stiff as you can (usually using solid mounts) is the best way to increase your driving precision by eliminating the deflection of rubber. The next best thing to create a balance would be to stiffen up the control arm with polyurethane, giving you the option of a more stock like feel with 80a or closer to the solid feel with 95a durometers.

When it comes to the E36 chassis you also get the options of choosing a stock centered design or going with the E30 inspired offset bushing to increase castor, further taking advantage of improvd handling. These poly bushings will give your control arms a direct connection between your suspension and the body of the car eliminating the slop felt under take-off and braking so you feel more in control of your vehicle.

This item fits the following BMWs that use a centered-style bushing: 

1984-1991 E30 BMW 318i, 318is, 325, 325e, 325es, 325i, 325is 
1992-1999 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic
1996-1999 E36 BMW M3 S50 S52
1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i MZ3 M Coupe M Roadster 

NOW LOCATED UNDER T#339018

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments