Turner Motorsport has everything you need to upgrade your BMW through our stages of performance or to keep your car in peak condition with our range of the latest in proven OEM cooling parts. Upgrade your cooling system and engine performance with the selections below to give your BMW a performance and reliability advantage.
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however, this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed/recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.
Show More Show Less
Due to weak plastic construction, the factory plastic crankcase ventilation breather hose is known to fail. After years of exposure to piping-hot engine bay temperatures and chemical-laden oil vapors, the corrugated plastic tubing can crack, crumble, or fail altogether.
We set out to bulletproof your M52/S52 CCV system with a durable silicone breather hose, designed to provide a comprehensive upgrade and permanent replacement for the factory plastic hose. By replacing the flimsy, heat-hardened OEM plastic hose with a four-ply fluorosilicone hose, you'll experience peace of mind knowing your M52 or S52 is free from the inevitable return of oil leaks, vacuum leaks, and drivability concerns that would have been.
This breather hose is found at the front of the engine, and is used to connect the cyclone separator to the valve cover. It replaces OEM part number 11151703775.
Features:
Silicone construction ensures a durable replacement that is sure to outlast OE plastic Designed as a direct replacement for the factory breather hose - not too short like many aftermarket alternatives, and does not require cutting to fit Works seamlessly with the OEM OBDII valve cover and cyclone separator, as well as the Turner Motorsport Billet Aluminum Valve Cover (T#26238386) Design:
Three-ply wire-reinforced fluorosilicone hose is designed to resist degradation due to exposure to oil vapors O-rings are pre-installed in OE Norma connectors for a lasting seal Includes pre-installed 430 stainless steel hose clamps for durability and corrosion-resistance Product Development:
Our Silicone CCV Hose Upgrade was designed, engineered, tested, and quality inspected by our Research and Development team in our Wadsworth, Ohio, facility. We strive for the highest level of precision and quality through leading-edge product development technology, including FARO laser scanning for reverse engineering and quality inspection, SolidWorks 3D CAD modelling, rapid prototyping utilizing our in-house 3D printer, and rigorous long-term product testing.
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however this does not limit you to this flow.
Show More Show Less
We know if a soft mount offers a sloppy connection it doesn't work on the track, and a solid mount isn't acceptable as a daily driver (for most!) and set out to engineer a mount that would meet the needs for both. At the core of our enclosed design is a partially-constrained, multi-piece polyurethane bushing with precisely-set preload. This architecture absorbs and disperses resonant engine frequencies as opposed to amplifying them (like some other designs do), which results in a positive-connection, enthusiast-feel mount with the vibration.
Show More Show Less
Underdrive Power Pulleys work to 'free up' horsepower. Any accessory that spins from the main drive belt is using up power. That's power that could otherwise be used to move the car. By giving some of that power back to the engine, you can make the car faster! It's like FREE HORSEPOWER! We measured 10.7 whp at 6960 rpm and 8.1 lb-ft of torque at 5550 on a 1995 M3.
Underdrive pulleys for your BMW will slow down engine-mounted accessories - the water pump, power steering pump, and alternator*. These systems contribute to 'parasitic losses' - power lost from what the engine could produce if it did not have these systems. Since less energy is used to move them, that power is transferred back to the engine and used to propel the car. Our pulleys give a 10-20% reduction in rotation, releasing up to 11hp on most BMW six-cylinder engines. There's also a small but noticeable improvement in throttle response too! We have done extensive testing and development work, both on and off the track, to ensure that the accessory systems function as they should. On our Racing pulley kits we actually underdrive certain components more so we feel our Street pulleys are an ideal compromise between power/torque gains, reliability, and system performance. Our pulley kits have been on the market for over ten years, and used in all of our own cars, with zero component failures related to their use.
Our pulleys are made from T-6061 aluminum and finished in a durable black hard anodize that is very resistant to wear, chemical exposure, and heat. We designed our pulleys to look similar to the factory parts but also to be stronger and, in most cases, slightly lighter too. For example, a Turner alternator pulley is less than half the weight of the stock steel pulley! With our hardcoat aluminum you will never have to worry about a serious failure of a stock plastic pulley. A 'stealth' approach to aesthetics was our goal and we let the results speak for the pulley design. Installation is straight forward and easy with simple hand tools. Removal of the fan is required for access to the front of the engine. Total install time for a 3-piece pulley set should be around 1.5 hours. A new longer belt is included and we also recommend replacing the separate A/C belt, belt tensioners, and the guide and deflection pulleys at the same time.
Alternator Pulley Options
(click to expand)
Bosch or Valeo? BMW built your car with either a Bosch or Valeo brand alternator. Unfortunately, the pulley is not the same for both brands. The brand is usually printed on the black plastic cover of the alternator but may be facing the frame rail or the ground. If you know which brand you have, select your option below and we'll send you the correct alternator pulley for your BMW. Don't know which you have? NO PROBLEM! We can send you both. The 2nd pulley costs $40 but you will receive a refund once we get the un-used pulley back (return shipping not included).
Aftermarket Stereo Systems
(click to expand)
We offer our kits in two different ways: the full Power Pulley Kit with all 3 pulleys or a 2 pulley kit if you do not wish to underdrive your alternator (for large stereo systems or other battery-draining modifications). Our kits have been tested for compatability with the factory premium stereo systems (Harmon Kardon, etc). But any major alterations or upgrades from the factory system will work best with our 2 pulley kit and no underdriving of the alternator. For all stock stereo systems the 3 pulley set is recommended because the Turner alternator pulley will help make more power and is also much lighter than the stock pulley.
This underdrive pulley kit fits the following BMW: 1991-1995 E34 5 Series 525i without servotronic steering and without self-leveling 1992-1995 E36 3 Series 325i, 325is, 325ic 1995-1995 E36 M3 3.0 liter (S50) **US models only, coupe 1996-1999 E36 M3 3.2 liter (S52) **US models only, coupe, sedan, convertible 1997-2000 MZ3 Z3 M Roadster & Z3 M Coupe (US models, S52US)
Show More Show Less
Introducing our newest upgrade for your E36: a full billet aluminum valve cover engineered to eliminate factory and aftermarket valve cover issues. If you're familiar with our new Turner Motorsport products for 2023 and 2024 you can tell that our engineering team at Turner has a focus on older chassis, especially the E36.
Our valve cover is designed to fit some of the best engines BMW ever came out with, single vanos M50/M52 and S50/S52. Not only are these great motors in general and deserve an upgraded valve cover but they are also prime for boosting. When adding boosting you will be introducing heat which can wreak havoc on your ignition system and make your factory valve cover extremely prone to failure.
The reality of the M5x/S5x motors is that the plastic valve covers are sub-par and the magnesium versions are no longer available from BMW and even those can even warp. You can end up replacing your valve cover time and time again dealing with issues if you prefer but the option is here for you. The last valve cover you buy for your E36.
Our engineers designed this valve cover with experience and personal passion that offers a plethora of benefits for your M5x/S5x motor. Whether you plan to cherish your E36 for years to come or envision a turbocharger upgrade, our valve cover is the ultimate solution. It boasts rugged durability and brilliant aesthetics, ensuring it's a perfect fit for any enthusiast.
Featuring full 6061 billet construction and a type-3 hard coat finish, our valve cover is built to endure extreme conditions and rigorous use. Whether you opt to retain your factory PCV setup or upgrade to a catch can for racing purposes, the cover provides dedicated, direct-fit ports for both configurations.
The base kit includes all the necessary components for a seamless installation. Additionally, the description provides part numbers for optional replacements and add-ons, ensuring you have everything you need to complete your install.
Features:
Integrated -10AN ORB ports for a catch can setup to keep your intake free from oil in racing applications Compatible with factory M5x/S5x ignition coil packs Compatible with Red Top "Smart Coils" (Audi R8) for standalone ECU applications Stainless steel coil pack heat shield for enhanced protection in factory and top mount turbocharger applications Compatible with factory oil cap Modular heatshield with bendable tab to accommodate 96-99 coil harness that crosses over the top of the exhaust manifold Online instructions included for PCV, heatshield and coil pack installation Benefits:
Leak-free - Never deal with a warped valve cover again thanks to the full billet aluminum construction Retains all factory PCV functions Protected ignition coils and wiring Superior heat resistance - Will not melt like plastic replacement valve covers Durable and clean anodized coating able to withstand excessive engine and exhaust temperatures Optimized oil path for vanos/timing chain lubrication Design:
Full 6061-T6 Billet Aluminum Type 3 black hard coat for increased durability and thermal capacity Compatible with all Single Vanos M5x/S5x engines Heat shield with black anodized Turner back plate for a clean and durable finish Designed to utilize M50/S50 valve cover gasket - fits all M50, M52, S50, S52 Kit options:
There are different PCV connections based on year splits for M5x/S5x motors. If you have a damaged or worn-out PCV component please reference the replacement component that matches your motor.
(1995 Only) Valve cover breather connector - P# 11151703710 (1996-1999) Replacement oil separator hose - P# 11151703775 Looking for catch can and or AN lines and fittings?
Right angle catch can feed/return lines - T#26493912 Feed/Return line separator - T#26493913 Universal catch can kit with mounting - T#398786
When we designed this catch we wanted to have the most function options available, the best separation method, and the easiest to service. The Turner engineered catch cans offer a pre-setup design based ion desired flow direction, however, this does not limit you to this flow. The inner baffle orientation can be easily adjusted to flow in both directions in case you decide to move this catch can to a different vehicle. A 4 chamber system baffle system inside the catch can was engineered to create multiple changes in the direction of airflow within the separator to cause oil droplets to fall out of suspension before exiting the catch can. Having a closed/recirculated design reduces oil ingestion and promotes cleaner emissions and odor-less operation.
Show More Show Less
BMW M50 S50 S52 Turner Motorsport Power Pulley Kit: Boost Your BMW's Performance
Increases horsepower and torque
Improves throttle response and acceleration
Lightweight design reduces rotating mass
Precision-engineered for perfect fitment
Upgrade your BMW's performance with the BMW M50 S50 S52 Turner Motorsport Power Pulley Kit. This kit is designed to increase horsepower and torque by reducing the rotational mass of the engine's accessories. With improved throttle response and acceleration, you'll experience a more dynamic driving experience. The lightweight design of the pulleys reduces rotating mass, resulting in improved engine efficiency. Plus, each pulley is precision-engineered for perfect fitment, ensuring seamless integration with your BMW's engine.
Through experimentation and data acquired from our E36 World Challenge Touring Cars, it was discovered that in long corners and under heavy braking that there was an oil starvation problem in the M50 and M52 engines. This system was developed to keep oil in the sump and eliminate the starvation problem. After several iterations, further testing and data acquisition in the Touring Cars showed that this system eliminates the problem of oil starvation. This is a less expensive alternative to replacing the stock oil pan with the factory BMW M3 Lightweight oil pan, while still achieving the similar results.
This item fits the following BMWs: 1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1992-1995 E34 BMW 525i 1997-1998 E39 BMW 528i 1997-1998 Z3 BMW Z3 2.8 1998-2000 Z3 BMW Z3 M Coupe M Roadster S52
Through experimentation and data acquired from our E36 World Challenge Touring Cars, it was discovered that in long corners and under heavy braking that there was an oil starvation problem in the M50 and M52 engines. This system was developed to keep oil in the sump and eliminate the starvation problem. After several iterations, further testing and data acquisition in the Touring Cars showed that this system eliminates the problem of oil starvation. This is a less expensive alternative to replacing the stock oil pan with the factory BMW M3 Lightweight oil pan, while still achieving the similar results.
This item fits the following BMWs: 1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1992-1995 E34 BMW 525i 1997-1998 E39 BMW 528i 1997-1998 Z3 BMW Z3 2.8 1998-2000 Z3 BMW Z3 M Coupe M Roadster S52
BMW E36 Z3 Turner Motorsport Power Pulley Kit is the ultimate performance upgrade for BMW enthusiasts. Designed by Turner Motorsport, this power pulley kit enhances engine performance and responsiveness, delivering an exhilarating driving experience. With its high-quality construction and precise engineering, it ensures durability and reliability for your BMW.
Designed by Turner Motorsport for optimal performance
The TMS E36 Stage 2 Oil Cooler Line Upgrade Kit is an ideal alternative to the factory oil cooler lines, with multiple added benefits. In combination with our TMS AN-10 Oil Line Adaptor Kit (Part # TEN9910200), installing the TMS E36 Stage 2 Oil Cooler Line Upgrade saves you time and money. Unlike factory lines, the TMS E36 Stage 2 Oil Cooler Line Upgrade can work with vehicles equipped with superchargers or racing alternator pulleys. The TMS oil cooler lines now sit safely away from any moving parts like pulleys and serpentine belts. Our lines are made from HTP (High Temperature Polymer Braided), a synthetic line with multiple advantages over rubber or stainless lines.
We picked HTP lines for four reasons: 1) it insulates the oil from heat better than rubber or stainless lines, 2) the hose can hold a tighter bend radius without crimping or restricting oil flow, which makes routing the oil lines easier and more versatile, 3) the HTP line are less abrasive than stainless steel braided lines so they won�t rub through your factory power steering lines or any other rubber hose on the car, 4) weight savings � even if it is not much remember it all adds up.
Please Note, the following parts are required to install these lines: � Euro oil filter housing � Euro oil cooler and mounts � (2) TMS AN-10 Oil Line Adaptor Kits (Part# TEN9910200)
This item was specifically designed for the following BMWs but may work in other applications: 1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 Show More Show Less
If allowed in the rules these solid aluminum engine and transmission mounts offer many advantages over a urethane or Delrin mounts. It's no wonder that these mounts have found their way into the top BMW racers in the country. We originally developed these mounts for E36 and E46 World Challenge racing but they also work perfect in BMW Modified and SCCA club racing and SpecE46 (SE46). These are machined from solid aluminum and have zero deflection. The engine torque will cause a rubber or urethane mount to flex or deflect. The stiffer the material the less movement there is and the more torque is passed through the driveline (instead of being wasted winding up the mount). At the transmission end the flex-free solid mounts will give smoother, crisper shifts since the transmission is no longer dancing on the pliable mount. This puts the shift linkages in better consistent alignment. And unlike rubber or urethane the aluminum has zero wear and is not affected by leaking oil or other fluids so this is likely the last set of motor and transmission mounts you will ever need. We have designed these mounts so the engine is 5mm lower and the transmission is 1mm lower than the factory mounts. This helps lower the center of gravity for better balance and handling. We very strongly recommend using the transmission and engine mounts together as a complete kit. Mixing a rubber mount with a metal mount will cause undue stress on the mouting points and will lead to a failure. We never advise using a solid mount unless a corresponding solid mount is also used. This kit fits the E36, E46, Z3, and Z4 6 cylinder models listed below, including M3 models.
These are a no-compromise design for all-out racing use. Full solid aluminum mounts should not be used on street-driven cars. Because there is no material to absorb vibration these will be quite harsh for regular street use (track cars don't care about noise).
Subframe reinforcement kits are very strongly recommended to go along with these solid motor mounts to reduce the risk of damage to the subframe. The motor mount section of the subframe should be reinforced to prevent stress and failure of the subframe.
This item fits the following BMWs: 1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 2001-2006 SpecE46 BMW 330i 330ci 1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2005 E85 BMW Z4 2.5i Z4 3.0i 2006-2008 E85 BMW Z4 M Roadster M Coupe Show More Show Less
This is a common failure item which can cause a check engine light, and rough engine running on the M52/S52 engines (328, M3, 528 thru 98, Z3 2.8, & M Roadster/Coupe thru 2000). If you have received an engine fault code suggesting "cam shaft reference sensor" or similar, this is most likely the cuprit. Once replaced, you will need to clear the fault code. We recommend replacing the cam position sensor o-ring at the same time.
OEM VDO is one of the largest OE providers in the world, supplying numerous vehicle brands, including BMW, with many of their genuine parts that build the vehicle before they ever reach the car lot. Entrusted by many of the top names in automotives and with their proven history of reliability, it makes all of us here at Turner confident that their line of OEM replacement parts are a perfect option to restore your vehicles original operation and performance. The same great quality or higher than Genuine BMW parts at a lower cost.
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform
The Crankshaft Position Sensor measures the speed and position of the crankshaft to determine the proper fuel and timing requirement for the best performance.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
Genuine BMW Pulse Generator This item fits the following BMW Chassis: E36 M3,E36
Every 60-80,000 miles, we recommend replacing your spark plugs to ensure your ignition system is running optimally. Over time carbon can build up around the head of the spark plug and decrease spark strength and effectiveness, leading to weaker fuel mixture detonation, misfires, and potential check engine lights. To prevent this, have put together our High-Performance Ignition Service Kits. These kits include new Bav Auto High-Performance Ignition Coils, new spark plugs, dielectric grease, and a BMW spark plug service label to keep track of when your spark plugs were replaced.
Bav Auto's Ignition coils feature core windings that have been modified to increase firepower and promote a faster, more efficient burn. This gives your BMW/MINI increased torque in the lower range of RPM and more horsepower in the upper range. Exact improvements depend on the current condition of your engine, but you'll definitely feel the difference. They'll also improve your fuel economy.
From 1974 to 2019, Bavarian Autosport was one of the premier vendors for BMW and MINI auto parts. We are happy to preserve the Bav Auto legacy by continuing to carry their high-quality products into the future. All Bav Auto parts will remain unchanged in design and sourced from the same OEM suppliers to ensure long-lasting reliability. We trust these parts, accessories, and upgrades so confidently that we back every Bavarian Autosport branded component with a 2-year warranty.
As a leading source of high-performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
Race German has devoted themselves to providing quality products for late model BMWs that cover both street and track applications. Race German has now grown their catalog to a wide variety of models and products geared towards keeping your car looking and running nice. BMW introduced VANOS in the early 90s, and it added variable valve timing to the straight six engines. Over time the VANOS unit wears out which can cause error codes or VANOS rattle. Race German has sourced quality replacement parts in an easy kit. Seal Kit: 1 PTFE Teflon Ring Seal 1 FKM (Viton) O Ring Seal 2 Copper Oil Pipe Washers Anti Rattle Bushing Set (1 Bushing + 2 Bearings) OEM Vanos Sealing Gasket *Note: a modified 18mm socket is needed to disassemble the VANOS unit. We are now offering this socket at a small charge. If you have a 1993 model single VANOS car, the 18mm socket will not work. You will need a modified 17mm socket. This kit includes the modified sockets.
Show More Show Less
Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)
Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.
ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.
These head studs fit the following BMWs/engines (steel block only) 1992-1995 M50 6 cylinder including 325i, 325is and 525i 1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i 1995-1995 S50US 3.0 liter including 1995 M3 (US only) 1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3
Show More Show Less
Don't neglect your motor mounts! The stock BMW motor mounts are fluid filled and the stiffness of the mount depends on this fluid. But over time the fluid leaks out and the strength of the mount is greatly reduced. A worn motor mount allows the engine to shift. The harder you're driving the more shift will occur. As the engine is moving around it can contact other parts in the engine bay - usually cooling related. The mechanical fan can hit the radiator; the A/C compressor can hit a radiator hose, the exhaust will flex and may break. Twisting of the engine can also lead to shifting problems as the transmission twists with it. There are countless issues related to worn or compressed motor mounts so don't overlook these as a regular replacement item (every 50,000 miles).
This is a replacement stock motor mount used on all M3s since 1995 and the Z4 M. It's also the standard motor mount for Z3 and E46 325xi/330xi models (left side). It can also used as an upgrade for non-M 1992-2006 E36 and E46 6 cylinder models because it's slightly stiffer to reduce flex and for a longer lifespan.
Sold per mount.
This motor mount / engine mount fits the following BMWs: 1995-1999 E36 BMW M3 2001-2005 E46 BMW 325xi 330xi (for left side only) 2001-2006 E46 BMW M3 2008-2011 E90 BMW M3 - Sedan 2008-2013 E92 BMW M3 - Coupe 2008-2013 E93 BMW M3 - Convertible 1997-2002 Z3 BMW Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2006-2008 E85 BMW Z4 M Roadster M Coupe
In addition, this can be used as a motor mount upgrade for these models: 1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic 1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci
Show More Show Less
Most of the pulleys on your BMW engine are plastic, which become brittle and frail over time and from engine bay heat. A failed pulley could leave you stranded which is why it is vital to inspect the pulleys during routine maintenance. This is an aluminum version of the stock water pump pulley used on the M50/M52/M52TU/M54 engine in the E36, E46, Z3, Z4, and other models. It uses the same hardware and the original belt as the stock plastic pulley. But the aluminum will last much longer.
Show More Show Less
When your car sits for a long period of time, your BMW's battery will gradually discharge. This battery charger will keep your BMW's battery fully charged and ready for your next driving adventure.
Collapsing and worn engine mounts can mean big trouble for BMWs. The stock mounts are filled with fluid that can leak or evaporate over time. That leaves the mount unstable and too flexible to properly support the engine. The side effects of a worn engine mount are: shaking and vibrating engine, driveline twist from engine torque that can break or snap bushings, and broken motor mount arms and bolts. If you're tired of replacing engine mounts you'll be very pleased with these solid rubber versions. Not only are these more reliable than stock fluid-filled mounts, they are slightly stiffer than new stock mounts thanks to a solid rubber construction (no voids in the rubber) but designed for street use so they remain quiet and comfortable. The solid rubber has less deflection than a stock mount, so no wasted engine motion. Less wasted motion gives you more torque to the wheels (it's not spent twisting the engine) and better engine response.
Show More Show Less
If you're experiencing hard starting, flaky charging, or other electrical issues, your engine ground strap may be the culprit. On older BMWs, the engine ground strap is a thin, non-insulated cable that spans from the engine mount arm to the frame horn. Despite the seemingly simple nature of this part, on older cars, it is known to cause massive headaches. Due to its non-insulated design, years of exposure to water, dirt, and road salt will cause the wire to corrode, ultimately leading to complete failure. A break in this cable will cause an open circuit, resulting in issues with the vehicle's electrical system and potentially leading to a no-start condition.
To solve this issue, ECS has engineered an exact-fit, upgraded ground strap for your BMW! Unlike its OEM counterpart, this design features insulated, large-gauge copper wire for dependable conductivity and long-lasting durability. Additionally, factory-style lugs are zinc-coated, crimped, and soldered, ensuring protection against corrosion and oxidation.
Whether you're replacing a visibly corroded strap or proactively preventing failure, this solution from ECS is sure to provide lasting performance and protection.
FEATURES
Direct-fit replacement and upgrade for E30 (318i/is), E36, E39, E46, and others Solves intermittent grounding issues caused by aging OEM straps Clean, stealthy design that fits seamlessly in factory engine bays Factory length and lug orientation for drop-in fitment 2 AWG tinned copper cable for excellent conductivity and corrosion resistance Zinc-coated lugs, crimped and soldered to resist moisture and oxidation Black UL1015-grade insulation withstands oil, heat, and abrasion Discreet ECS label for a clean, OEM+ look Replaces OEM part numbers 12421737755 and 12421714262.
A new oxygen sensor can improve driveability and lengthen engine life. Ultimately, you achieve a smoother running engine that is more fuel efficient. Feedback from the oxygen sensor provides closed-loop control of the injected quantity of fuel for optimum air-fuel mixture, enabling virtually complete combustion to take place. Contaminants in gas and certain atmospheric conditions can drastically shorten the life of any oxygen sensor, therefore they should be checked with every periodic maintenance and changed if necessary. Bosch Part # 13 231. Replacement for BMW part # 11781735499 and 11781738282.
Bosch is one of the largest OEM producers of Genuine BMW and aftermarket parts in the world, providing parts for almost every major automotive manufacturer. Bosch has likely supplied many of the original electrical (and mechanical) parts for your BMW. Thanks to their quality, high durability, and reliability, you should expect a long service life from Bosch products.
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
This item fits the following BMWs: 1988-1991 E30 BMW 325i 325is 325ix 325ic 1992-1995 E36 BMW 318i 318is 318ic 318ti 1992-1995 E36 BMW 325i 325is 325ic M3 1993-1995 E34 BMW 530i 1993-3/1994 E34 BMW 540i 1993-1994 E32 BMW 740i 740il 1988-1994 E32 BMW 750il 1990-1994 E31 BMW 850i 850ci
Turner Motorsport BMW Timing Chain Tensioner Replacement
Introducing the BMW Timing Chain Tensioner Replacement by Turner Motorsport, a vital component to maintain optimal tension and prevent timing chain issues. Engineered for reliability, this replacement ensures the proper functioning of your cam gears and crank, preventing potential engine damage.
Benefits:
Crucial for timing chain tension
Prevents chain skipping
Safeguards against catastrophic engine damage
Quiets noisy chains for a smoother engine operation
Replace your BMW's timing chain tensioner with this Turner Motorsport solution to keep your engine running smoothly.
Stock mounts are made from soft rubber and are sometimes filled with fluid to give a car the most comfortable ride possible. The soft rubber and fluid helps to reduce the total amount of vibration, noise, and harshness (NVH) that is transferred into the cabin. The problem with this is driveline slop. The stock mounts allow a lot of excess movement and increases the amount of time it takes to transfer power to the wheels.
In order to address this issue, performance mounts can be substituted to reduce the amount of slop and transfer power to the wheel quicker. Two options for this are polyurethane mounts and solid mounts.
Solid mounts are great for an immediate transfer of power but allow for a ton of noise and vibration to be felt and heard in the cabin of the vehicle. This is great for the track where there aren't any issues with excess harshness, but as a daily driver, this can become an annoying pain in the neck.
The best middle ground is Polyurethane. Polyurethane is much stiffer than rubber and gives you the much stiffer feel you may be looking for. This allows for the increase in responsiveness, but isn't so extreme that it transfers all of the sound and vibrations into the cabin. This makes it much more comfortable for daily use while still reinforcing your driveline.
This OEM Ruville hydraulic tensioner assembly is designed to keep the serpentine belt at the correct pressure against the pulleys. Many BMW's can have either a hydraulic or mechanical belt tensioner. Please check to see which tensioner type you need before ordering.
OEM Schaeffler (INA, LuK, Ruville, & FAG) is an engineering company that focuses on high-performance, precision manufacturing. With their individual brands INA, Luk, and FAG providing exceptionally high quality parts directly to BMW, as well as countless other automotive companies, their history of reliability and variety of offered parts makes Schaeffler a go-to replacement parts provider for all of us here at Turner Motorsport.
As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts. All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!
This item fits the following BMWs: 1992-1998 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 1991-1995 E34 BMW 525i 1997-2003 E39 BMW 525i 528i 530i
With exposure to heat and elements, your motor mounts will break down with increasing age. A secure mount is vital to reduce drivetrain vibration and transfer as much horsepower to the wheels as possible. These mounts are an upgrade for non-M E36/E46 owners seeking a stiffer mount without sacrificing comfort and ride quality.
Show More Show Less
Upgrade your BMW's oil pressure sensor setup with the Oil Distribution/Sending Block. This versatile block is designed to mount in the stock oil pressure sensor location on the oil filter housing or in the original location on the engine block. It allows the use of up to two aftermarket sending units (not included) along with the factory sensor, providing accurate pressure and temperature measurements. Engineered for reliability and cleanliness, it ensures a reliable setup for your BMW's oil pressure monitoring needs.
Mounts in stock oil pressure sensor location for easy installation
Allows use of up to two aftermarket sending units in addition to the factory sensor
Incorporates factory sending unit for utilizing the factory oil pressure light
Threaded for one M12x1.5 port and two 1/8th NPT ports for versatility
Includes banjo bolt and crush washers for secure installation
Compatible with various BMW engines including M20, M42, M50, M52, M54, N52, N54, S50, S52, S54, S65, M10, S14, and M30
These mounts are designed for the BMW E36 and E46 including the M3, Z3, and Z4 as well as the E90/E92 M3. Excluding the E46 XI. Revshift polyurethane motor mounts are made in the U.S.A. from high-grade polyurethane. Revshift mounts are the most durable and reliable mounts on the market. CNC machined billet aluminum flanged ends are embedded deep in the urethane which prevents the isolated ends from separating under extreme loads. Utilizing class 14.9 alloy steel removable screws these mounts will hold your engine in place for a lifetime. To further ensure the strength of these mounts we form the threads with a forming tap which creates denser and stronger threads in the billet aluminum end pieces. These mounts have removable screws for ease of installation. We recommend using Loctite on the threads during installation. Revshift Performance Engineering is a high-performance parts manufacturer with a focus on quality, reliability, and performance. Utilizing high-precision machining technologies and their very own Polyurethane Manufacturing Department, every Revshift product is designed, manufactured, and tested in-house at their Detroit, Michigan facility.
Show More Show Less
This ARP main stud set for the 24 valves M50-based 6 cylinder engines (including M50, M52, S50US and S52US) and eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This main stud kit includes hardened parallel-ground washers and aerospace quality nuts. Replaces BMW part numbers 11-11-1-713-525 (11111713525) and 11-11-2-244-286 (11112244286).
The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.
ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.
This ARP main stud kit fits the following BMWs: 1991-1995 E34 525i (24v, M50 and M50TU) 1992-1995 E36 325i, 325is (M50 non-VAN0S & M50TU VAN0S) 1996-1998 E36 328i, 328is (M52) 1994-1995 E36 M3 3.0 liter (US spec) 1996-1999 E36 M3 3.2 liter (US spec) 1997-1998 E39 528i (single VAN0S) 1997-1998 Z3 2.8 liter 1998-2000 MZ3 M Roadster / M Coupe
Show More Show Less
These are the "Yellow" main bearing shells for many BMW 4 and 6 cylinder engines. The size is 60.00mm. Set includes bearings for 6 cylinder cars. 4 cylinder cars get 2 spare bearing sets.
KS Kolbenshmidt designs and produces internal parts for gasoline and diesel engines and is an OEM choice for many automakers. Both increased power handling and reduced fuel consumption are the motivating factors behind this company and they continue to innovate every day.
This item fits the following BMWs: 1990-1991 E30 BMW 318i 318is 318ic 1984-1991 E30 BMW 325e 325es 325i 325ic 325is 325ix 1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3 1989-1990 E34 BMW 525i 1997-2003 E39 BMW 525i 528i 530i 2004-2005 E60 BMW 525i 530i 2000-2006 E53 BMW X5 3.0i 2004-2006 E83 BMW X3 2.5i X3 3.0i 1997-2002 Z3 BMW Z3 1.9 Z3 2.3 Z3 2.5i Z3 2.8 Z3 3.0i M Roadster M Coupe 2003-2006 E85 BMW Z4 2.5i Z4 3.0i - M54 2006-2008 E85 BMW Z4 M Roadster M Coupe
Show More Show Less
Elevate your BMW maintenance with this comprehensive tool kit designed for valve and valve stem seal removal and replacement, all without the need to remove the head. This time-saving kit ensures efficiency and ease in the process, making it an essential for DIY enthusiasts and professionals alike. The universal fitment and a range of adapters guarantee versatility across various brands and motors, providing maximum utility.
Removes and replaces valves and valve stem seals without head removal
Time and effort-saving solution
Wide range of adapters for versatile use
Universal fitment for compatibility with different brands and motors
DeatschWerks was founded in 2004 in Oklahoma and has dedicated themselves to providing high quality EFI applications to a wide variety of manufacturers. DW has developed a wide variety of innovative fuel system components including fuel pumps, modular surge tanks, conversion fuel rails, dual-stage fuel filters, and ethanol compatible fuel pressure regulators. The DW300 is DeatschWerks' flagship standard fitment in-tank pump. The DW300 flows 340lph at 40psi and is a popular choice for e85 applications or wherever the highest flowing standard fitment in-tank pump is needed. Quiet operation and pulse width modulation compatibility are delivered via the turbine impeller and computer balanced armature. E85 compatibility is built in via the carbon commutators and a fully encapsulated armature. All DW fuel pumps are backed by a 3-yr no fault warranty. Features: Weight 12.6 oz (360grams) 7.7mm ID/11mm OD inlet fitting Outlet 5/16" Hose Clamp Single Scroll Composite Turbine All instructions are also provided on DeatschWerks' website.
Show More Show Less
If there is a large amount of oil on the sides of the engine or if you can smell burning oil, chances are it's a bad valve cover gasket. The gasket fails and allows oil to seep down onto the side of the engine and other parts causing a mess and reducing the amount of oil in your engine. This replacement gasket from Elring is perfect to prevent any further oil leaks.
Includes everything needed to re-seal your engine's head.
Elring is one of the biggest OEM names in the manufacturing of high quality gaskets that are available for very affordable prices. Elring has supplied many automotive names for years with the gaskets that seal your car's components from day 1 so you can rest assured that these components will last for a long time to come!
If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.
To avoid improper cam timing on the latest BMW engines, the factory has devised a cam timing system that locks the crankshaft and cams into a specific position prior to cylinder head removal. This method was devised to avoid any misalignment, resulting in piston to valve damage. Unfortunately without these tools re-timing the camshafts after a valve job is almost impossible. The factory specification manual does not supply installation specifications. This cam timing kit includes all the necessary components to do the job.
This item fits the following BMWs: 1990-1991 E30 BMW 318i 318is 318ic 1992-1998 E36 BMW 318i 318is 318ti 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3 1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi
NOTE: Not compatible with S50B30 and S50B32 Euro engines!If you have ever attempted to do a valve job or cylinder head gasket project on an M42, M44, M50, or M52 engine you know that the repair manual will refer to the special BMW timing tool kit. This tool kit includes a flywheel locating lock pin, and a special set of camshaft locators that lock the cams in a precise location. The tools are very easy to install. The kit is specifically designed to hold the engine and cams in proper timing during the cylinder head removal and re installation process. This avoids the chance of bending the valves doing the head install process. The precision ground holding blocks lock over the square ends of both intake and exhaust cams. The CNC machined flywheel locating pin passes through a hole in the rear of the engine block and passed through a machined hole in the flywheel.
Feeds oil to the VANOS unit from the oil filter housing.
When doing any sort of repair or maintenance there is no replacement for genuine factory parts. Turner Motorsport carries the Genuine BMW brand with pride and has the parts you need to complete your next project with confidence.
This cap is designed to use the original O-ring seal so no special parts are required. The satin black anodize blends in with the rest of your engine bay making this a smart and subtle upgrade. Made in the USA!
Show More Show Less
Discover precision tailored to BMW and MINI enthusiasts with the Schwaben 3/8" Drive Digital Torque Wrench – a fusion of precision, convenience, and lasting quality that defines your enthusiast spirit. Elevate your car maintenance with the convenience of digital precision, backed by our LIFETIME REPLACEMENT program that underscores our commitment to quality. Features: Precision Perfected: This torque wrench merges micro-adjustable excellence with a digital display of torque units, guaranteeing accuracy that aligns with professional standards. Easy to Read: This wrench's digital screen allows for a quick glance to suffice when checking your torque so you don't have to search for it! Versatile Control: The reversible 3/8" drive 45-tooth head, coupled with a push-button release, empowers you with effortless operation. Tailored Torque: With a range of 15-80 ft-lbs and 20-110 N-m, it's engineered to excel across various applications. Unit Variety: Read torque effortlessly in your preferred metrics: ft-lbs, N-m, Inch-lbs, cm-kg2, and m-kg. Designed for Comfort: Its ergonomic 16" (370mm) length ensures comfortable handling, precision, and control. Unwavering Accuracy: With a remarkable accuracy within +- 3%, every task becomes a statement of confidence. On-the-Go Ready: Housed in a user-friendly blow-molded case, this torque wrench is primed for storage and mobility. Continuous Power: The included 3V CR2032 battery ensures seamless operation, offering you uninterrupted convenience.
Show More Show Less
The early M5X engines have well-documented issues caused by harmonics. The extreme vibrations cause the weak oil pump shaft to shear off or the oil pump nut to come loose and fall off, all of which results in an instant loss of oil pressure. Achilles Motorsports decided to develop a solution to fix all of these known issues. Achilles takes their oil pump shafts to the extreme, using only the toughest materials and heat treatment processes to ensure optimum strength. The core of this kit is a hardened Chromoly shaft that is centerless ground to ensure absolute trueness. The shaft is engineered with an exclusive square key lock system that not only prevents the gear from ever spinning on the shaft but also adds strength to the area to which the gear mounts. Achilles Motorsports then replaced the pesky oil pump nut with an extended length bolt that is EDM drilled for safety wire to properly secure it for all conditions. Don't wait for your oil pump to fail and leave you stuck with costly engine repairs! Key Features: Hardened Chromoly centerless ground shaft EDM Drilled Bolt with a piece of safety wire included Grade 8 extended length hardware to secure the gear to the shaft Left hand threaded to prevent it from unexpectedly coming loose Double-D keyed shaft and drive gear 100% serviceable & rebuildable without the need for grinding. NOTE: Professional installation required! The shaft requires being pressed into the oil pump's inner rotor.
Show More Show Less
The Achilles Motorsports Oil Pan Baffle was designed and manufactured to be used on racing, high-performance track, and street driven cars. Each baffle is precision laser cut from .090" heat-treated aluminum then hand-assembled and test fit to ensure accuracy and ease of installation. Achilles Motorsports' baffle design incorporates dual trap doors and a unique oil deflector that prevents oil from splashing out of the sump under hard braking. Together, these help minimize the sloshing of the oil inside the oil pan and keep oil accumulated around your pickup tube. The factory BMW oil pan doesn't do a very good job of keeping oil accumulated around the oil pick-up tube in high g-force situations. By keeping oil accumulated around the pickup tube you can eliminate the costly loss of oil pressure and potential damage to other vital engine parts commonly caused by high g-forces from hard acceleration and braking and high-speed cornering. Professional welding is required for installation! During installation, while the oil pan is removed, we HIGHLY RECOMMEND upgrading your factory oil pump with the Achilles Motorsport Upgraded Oil Pump Shaft Kit (T#1150772). After numerous instances of sheered-off oil pump shafts and oil pump nuts coming loose, resulting in an instant loss of oil pressure, Achilles decided to come up with a solution - Don't let it happen to you!
Show More Show Less
BMW E36 E46 M50 M52 In-Tank Fuel Pump DeatschWerks DW300 340 LPH With Install Kit is a high-performance fuel pump engineered for BMW models requiring a reliable and efficient fuel system upgrade. The DW300 is DeatschWerks' flagship in-tank pump, delivering superior flow and compatibility with ethanol fuels. It includes an installation kit for select 6-Cylinder E36 and E46 models, including the E36 and E46 M3.
High Flow Rate: Delivers 340 liters per hour at 40 psi, ideal for high-performance and E85 applications.
Quiet Operation: Features a turbine impeller and computer-balanced armature for minimized noise.
E85 Compatible: Built with carbon commutators and a fully encapsulated armature to handle ethanol fuels.
Comprehensive Kit: Includes a complete installation kit for select BMW E36 and E46 models.
Durable Design: Backed by a 3-year no-fault warranty for reliable performance.
Features:
Weight: 12.6 oz (360 grams)
Inlet Fitting: 7.7mm ID / 11mm OD
Outlet: 5/16" Hose Clamp
Turbine Type: Single Scroll Composite
Installation instructions are available on DeatschWerks' website.
The Hydraulic Alternator Belt Tensioner is exposed to a lot of dirt, salt, and other debris due to its front lower location. This can cause the tensioner to seize and not allow the belt tensioner to adjust. Replace your belt tensioner with this OEM high quality hydraulic tensioner for many years of reliable operation to come.
Show More Show Less
We have seen so many M50/S50 Vanos line failures at the track that we have to offer you a solution. The factory line is prone to failure due to the OEM hard-line - this stainless steel line alleviates the issues imposed by the factory design and enables you to worry less about your Vanos system. We trust ECS's Exact-Fit Rubber Vanos lines, are the most economical replacement line for several different applications, and their M50/S50 Vanos line is no exception. ECS Tuning's M50/S50 Exact-Fit Stainless Steel Vanos Line offers several benefits over OEM. Not is it they more durable and reliable OEM, but it is also easier to install, and significantly less expensive than the factory BMW Vanos line (11361703464) or other alternatives available on the market. If you're factory Vanos line hasn't failed yet, we still recommend replacing yours with ECS Tuning's Exact Fit Stainless Steel Vanos Line M50/S50 to avoid eminent future failure.
Show More Show Less
The timing chain tensioner from the 1995 E36 M3 is a great upgrade for other Motorsport models - 1988-1991 E30 M3 and 1989-1995 E34 M5! This tensioner virtually eliminates the cold start-up engine rattle so common with the S14 and S38 engines. It makes the whole engine quieter and smoother. Any new tensioner will accomplish that but the S50 tensioner has several new features that make it superior to the original design. This unit also has a internally loaded spring, so installation is much easier than the old style tensioner (no need to squeeze the spring and hold it while installing). Includes oil seal ring (not pictured).
This item fits the following BMWs: 1985-1989 E24 BMW M635CSi M6 - M88/3, S38B35 engine 1988 E28 BMW M5 - M88/3, S38B35 engine 1988-1991 E30 BMW M3 - S14 engine 1989-1995 E34 BMW M5 - S38 engine 1995 E36 BMW M3 - S50B30US engine 1994-1999 E36 BMW M3 Euro - S50B30 and S50B32 engines Show More Show Less
The TMS E36 Stage 2 Oil Cooler Line Upgrade Kit is an ideal alternative to the factory oil cooler lines, with multiple added benefits. In combination with our TMS AN-10 Oil Line Adaptor Kit (Part # TEN9910200), installing the TMS E36 Stage 2 Oil Cooler Line Upgrade saves you time and money. Unlike factory lines, the TMS E36 Stage 2 Oil Cooler Line Upgrade can work with vehicles equipped with superchargers or racing alternator pulleys. The TMS oil cooler lines now sit safely away from any moving parts like pulleys and serpentine belts. Our lines are made from HTP (High Temperature Polymer Braided), a synthetic line with multiple advantages over rubber or stainless lines. 
