Turner Motorsport for BMW 3 Series E36 (1992-1998)

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

Increasing the negative camber of your 1995 E36 M3 will reduce understeer and prolong the life of your tires when used on the track. These plates simply bolt on top of the factory upper strut bearings and increase negative camber by 2 degrees. We maximized the available camber available with a stock-diameter sized spring. Vehicle height in the front will be raised by .25". We also added material to the surface area of the mount to increase stiffness of contact area, therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal for many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class.

Instructions for Turner 1995 E36 M3 Front Fixed Camber Plates

This item fits the following BMWs:
1994-1995 E36 BMW M3

Turner Motorsport Polo shirts are perfect to show your passion for the race team when you're not in the garage. Pick one up today!

Don't see your size available? Give us a call at 1.800.280.6966 - we have you covered.

Through experimentation and data acquired from our E36 World Challenge Touring Cars, it was discovered that in long corners and under heavy braking that there was an oil starvation problem in the M50 and M52 engines. This system was developed to keep oil in the sump and eliminate the starvation problem. After several iterations, further testing and data acquisition in the Touring Cars showed that this system eliminates the problem of oil starvation. This is a less expensive alternative to replacing the stock oil pan with the factory BMW M3 Lightweight oil pan, while still achieving the similar results.

*Requires Professional Welding

Installation instructions (E36/Z3 Oil Pan Baffle for M50, M52, S50, S52 engines)

This item fits the following BMWs:
1992-1999 E36 BMW 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1992-1995 E34 BMW 525i
1997-1998 E39 BMW 528i
1997-1998 Z3 BMW Z3 2.8
1998-2000 Z3 BMW Z3 M Coupe M Roadster S52

BMW E36 Z3 Turner Motorsport Power Pulley Kit is the ultimate performance upgrade for BMW enthusiasts. Designed by Turner Motorsport, this power pulley kit enhances engine performance and responsiveness, delivering an exhilarating driving experience. With its high-quality construction and precise engineering, it ensures durability and reliability for your BMW.

• Designed by Turner Motorsport for optimal performance
• Enhances engine performance and responsiveness
• High-quality construction for durability
• Precise engineering for reliability

Over the years, it is not uncommon for exhaust tips to be damaged and corroded, becoming a "sore spot" of your BMW. To remedy this unsightly feature, we now offer our very own exhaust tips! Featuring stainless steel construction and a simple, yet sporty design, this exhaust tip will look perfectly at home on almost any model.

Features & Specifications:

3.0" Inner Diameter
4.0" Outer Diameter
Black Chrome Finish
Double Wall Construction
Slant Cut Style
Includes Stainless Steel Clamp

TMS E36 solid sub-frame bushings are designed for track and racecars to remove twisting and flexing of the subframe where it mounts to the rear floor. This twisting is one of the causes of rear subframe/floor failure in E36 cars. We originally developed these for our SCCA SPEED World Challenge cars. A BMW's subframe is the heart of the suspension. Because the subframe is mounted with rubber isolators, when the subframe moves, so does the rest of the suspension mounting points. As the rubber wears and becomes more pliable, the alignment and suspension settings move even more. Replace the stock rubber bushings to limit drivetrain and suspension movement and keep your car set up the way it's supposed to be.

Our mounts are designed using a CAD program with further attention paid to making the mount as light as possible. We also notched the flanges to allow the use of the BMW factory removal tools. One front bushing is slotted to allow for compliance between manufacturing standards as BMW specifies. These bushings are CNC machined out of high grade billet aluminum.

Click for installation instructions. (PDF)

NOW LOCATED UNDER T#339018

Lowering your BMW does wonders for appearance and handling, but it also changes suspension geometry in ways that can hurt performance. As ride height changes, angles between the sway bar, control arms, and axles shift, which can cause binding, poor fitment, and added stress on the factory fixed-length end links. This is especially noticeable on cars equipped with coilover suspension, where slight height differences side to side can preload the sway bar and lead to inconsistent handling.

Our team of dedicated BMW enthusiasts set out to remedy this common issue with a set of Adjustable Rear Sway Bar End Links. Designed with performance in mind, they offer a fully adjustable range from 100mm to 120mm, helping eliminate preload, restore proper suspension alignment, and improve overall sway bar function. Constructed from high-quality billet aluminum, these end links are built to outlast the factory cast components and are finished with a black anodized coating for excellent corrosion resistance. Laser-etched wrench size markings allow for quick, easy adjustments while installed on the vehicle. Unlike the factory design, these end links use spherical rod ends at the control arm for increased responsiveness and a more direct handling feel. A unique knurled bushing design also ensures compatibility with the OEM sway bar, offering a first-to-market solution for enthusiasts looking to retain factory components.

Features & Benefits:

Adjustable from 100mm to 120mm Strong 6061-T6 billet aluminum construction Black anodized finish resists corrosion Spherical rod ends improve response and handling feel Polyurethane bushing with knurled bore helps retain grease Fits factory rear sway bars on E23, E24, E28, E30, and E36 Laser-etched markings for quick and easy adjustments

Let's face it, the E36 is an old chassis but it's still the most popular car to build for track-use. But because of it's age, certain parts of the chassis are prone to structural failure. We've been racing the E36 for over ten years so we know what the weak points are and how to make them stronger. Included with this package are the reinforcement kits that are absolutely necessary for a car that sees any time on the track. Street cars will also benefit from these pieces as your car can take almost as much of beating on the road as on the racetrack.Buy as a package and save 10%! Package includes reinforcements for the following areas:

• front subframe
• front strut towers
• front strut tower paper gaskets
• rear sway bar / swaybar tabs
• rear shock towers
• rear subframe
• rear camber arms (optional)

​This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 323is 325i 325is 328i 328is - Not M3