BMW Internal Engine Parts for BMW 3 Series E46 (1999-2005)

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

For vehicles with production from 02/2003

T#:2206

Part#: 201-6102

In Stock

$ 119.99

This product was last offered at the strikethrough price on
10-01-2026

$ 116.99 USD

Add to Wish List

Qty

$ 116.99 USD

Add to Wish List

Set of 12 ProSeries ARP2000 connecting rod bolts for the Euro-spec M3 engine. Made by ARP, the world leader in fastener technology. The best rod bolts available for the Euro S50 and S54. Ideal for ultra high performance, racing & forced induction applications. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in professional motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods.

This set replaces the factory BMW Euro S50B30 and B32 rod bolts with part number 11-24-1-317-184 (11241317184) and 11-24-1-405-890 (11241405890). It's also used for S54 engines with stock M10 sized rod bolts, which were used from February 2003 production and later. It was also used in earlier engines that had connecting rods replaced. For these 2001-2003 models there is no easy way to check if the rods were replaced, except by checking the rod bolt diameter. If your car has the earlier M11 sized bolt, use ARP kit #201-6103 . Before opening the ARP kit, we recommend that you check your existing rod bolt size as BMW was not consistent with their applications. ARP bolts are not returnable if the package has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1993-1999 E36 BMW Euro M3
2001-2/2003 E46 M3 coupe / convertible*
2/2003-2006 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe*
2006-2008 MZ4 M Roadster & M Coupe
* - these engines could have either M10 or M11 sized bolts. If the rods and rod bearings were replaced under recall by BMW it should have the newer M10 bolts and this is the correct ARP set to order.

Show More Show Less

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

T#:3315

Part#: 201-6303

In Stock

$ 212.99

This product was last offered at the strikethrough price on
10-12-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the 47mm length factory BMW rod bolts with part number 11-24-7-589-671 (11247589671) Check applications before ordering! Opened ARP bolt kits are not
returnable.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This item fits the following BMWs:
1999-2005 E46 BMW 328i 328ci 330i 330ci 330xi
2001-2003 E39 BMW 530i
2004-2005 E60 BMW 530i
2004-2006 E83 BMW X3 3.0i
2000-2006 E53 BMW X5 3.0i
1997-2002 Z3 BMW Z3 3.0i
2003-2005 Z4 BMW Z4 3.0i

Show More Show Less

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

T#:3606

Part#: 201-4302

In Stock

$ 240.99 USD

Add to Wish List

Qty

$ 240.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best head studs we've found for the E36 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines (steel block only)
1992-1995 M50 6 cylinder including 325i, 325is and 525i
1996-1999 M52 6 cylinder including 328i, 328is, 323is, 528i
1995-1995 S50US 3.0 liter including 1995 M3 (US only)
1996-1999 S52US 3.2 liter including 1996-1999 M3 (US) and MZ3

Show More Show Less

ARP Connecting Rod Bolt Kit - Early S54 - E46 M3, MZ3 (M11x47mm Size)...

For vehicles with production up to 02/2003

T#:2211

Part#: 201-6103

In Stock

$ 215.99 USD

Add to Wish List

Qty

$ 215.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

These bolts are M11 size to replace the stock M11 BMW bolt part number 11-24-7-834-310 (11247834310). The M11 bolt size was used in S54 engines up to 2/2003 production. However, most S54 engines up to that point had their rod bearings replaced under a factory recall and some may have had new connecting rods installed at the same time (or even a new engine altogether). The new bolts installed in these earlier engines are M10 size. Unfortunately, there is no way of knowing which rod or bolt is currently in your car (unless your car came with service records detailing when and what was replaced). The only sure way to know is to check the bolts currently installed in your engine. If yours was updated to the M10 sized bolt, use ARP kit #201-6102 . ARP bolts are not returnable if the pacakge has been open.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
2001-2/2003 E46 M3 coupe / convertible
2001-2002 MZ3 M Roadster & M Coupe

Show More Show Less

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

T#:3631

Part#: 201-4303

In Stock at Vendor

$ 247.99 USD

Add to Wish List

Qty

$ 247.99 USD

Add to Wish List

Virtually every top professional BMW engine builder relies on ARP Pro Series head studs, particularly on the S54 3.2 liter engine. ARP uses a premium grade 8740 alloy that is rated far superior to "aircraft" quality. Each stud is heat-treated to 200,000 psi, ensuring complete heat penetration. ARP studs are threaded after heat-treat, which gives them 1000% (that's ten times!) better fatigue strength than studs threaded prior to heat-treat. Threading the studs after heat-treating is more difficult and costly (as it's harder on tooling) but the results are well worth the effort. These simply are the best S54 head studs we've found for the E46 M3 6 cylinder engines, and we highly recommend them in both the racing and forced induction arena. (Due to the additional clamping force between the head and block, these are IDEAL for turbo charging and supercharging!)

Converting from the factory BMW head bolts to head studs makes it much easier to assemble an engine, especially a racing powerplant which must be serviced frequently (and quickly!), and also ensures proper alignment of the head and gasket. Head studs also provide more accurate and consistent torque loading. Here's why: When you use bolts to secure the head, the fastener is actually being "twisted" while it's being torqued to the proper reading. Accordingly, the bolt is reacting to two different forces simultaneously. A head stud should be installed in a "relaxed" mode -- never crank it in tightly using a jammed nut. If everything is right, the stud should be installed finger tight. Then, when applying torque to the nut, the stud will stretch only on the vertical axis. An information sheet is provided with each set. Kit includes everything pictured -- 14 head bolts, washers, bolts and assembly lubricant.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These head studs fit the following BMWs/engines
2001-2006 E46 M3 coupe & convertible
2001-2002 MZ3 M Roadster & M Coupe (with S54 engine)
2006-2008 MZ4 Z4 M Roadster & M Coupe

Show More Show Less

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

T#:2210

Part#: 201-6201

Ships in 7 Business Days

$ 222.99

This product was last offered at the strikethrough price on
08-13-2026

$ 194.99 USD

Add to Wish List

Qty

$ 194.99 USD

Add to Wish List

Set of 12 ProSeries connecting rod bolts, made by ARP -- the world leader in fastener technology. Each bolt is made of ARP2000 material, which exceeds the strength of 8740 Chrome Moly, and is able to achieve clamp load at 220,000psi. ARP2000 fasteners are used widely in motorsport and drag racing as an upgrade from 8740 Chrome Moly in both steel and aluminum rods. These are simply the best connecting rod bolts available, making them ideal for ultra high performance, racing and forced induction applications.

This set replaces the factory BMW rod bolt number 11-24-1-739-728 (11241739728) which measures 44mm in length. The 44mm BMW rod bolt was used on all US spec E36 M3 (3.0 and 3.2 liter), 1999-2000 E46 323i/323Ci, 2001-2005 325i/325Ci, Z3 1.9,2.5 and 3.2, as well as Z4 2.5. It was also used on SOME of the M50 2.5 liter engines from 1992-1995 -- but check before ordering! Opened ARP bolt kits are not returnable. If your M50 2.5 liter engine has 53mm rod bolts, you will require kit part# 201-6301 instead.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

These ARP connecting rod bolts fit the following BMWs:
1992-1995 E36 325i/is *** with 44mm rod bolts only ***
1995-1995 E36 M3 S50 3.0 liter (US model)
1996-1999 E36 M3 S52 3.2 liter (US model)
1999-2000 E46 323i & 323Ci (US)
2001-2005 E46 325i, 325xi & 325Ci (US)
1998-2002 Z3 2.3 / 2.5 liter
1998-2000 MZ3 M Roadster & M Coupe
2003-2005 Z4 2.5 liter
*** DOES NOT FIT E36 328 ****

Show More Show Less

ARP Main Stud Kit for S54 (E46M3 & Z4M)

T#:2192

Part#: 201-5002

In Stock at Vendor

$ 171.99 USD

Add to Wish List

Qty

$ 171.99 USD

Add to Wish List

This ARP main stud set is for the S54 3.2 liter, as found in all 2001 to 2006 E46 M3, as well as the 2006-2008 Z4 M Roadster and M Coupe models. Switching to the ARP main stud kit eliminates main cap walk and fretting, as well as protects the threads in your engine block. Each stud is made using the best materials, process, design and engineering, which exceeds even the most stringent racing and aerospace specifications. This S54 main stud kit includes hardened parallel-ground washers and aerospace quality nuts.

The studs are manufactured from 8740 chrome moly steel, heat-treated in-house to 190,000 psi tensile strength, and precision J-form threads rolled after heat-treat to create a fastener that has threads 1000% stronger than others. On the E30 M3, there's no reason to settle for anything less than the best, which is why we carry and use ARP fasteners and studs on our own BMW race cars.

ARP is a company that prides itself on performance and durability, no matter the application. Offering the finest engine hardware money can buy is the driving initiative at ARP and this is evidenced by the staggering amount of satisfied customers and race teams the world over.

This ARP main stud kit fits the following BMWs:
2001-2006 E46 M3 3.2 liter coupe/convertible
2001-2002 MZ3 M Coupe & M Roadster (S54 engine)
2006-2008 MZ4 M Coupe & M Roadster

Show More Show Less

Main Stud Kit - M50/M52/S50/S52

T#:26171653

Part#: ARP-MSK-M50

Back Ordered

$ 169.99 USD

Add to Wish List

Qty

$ 169.99 USD

Add to Wish List

This ARP Main Stud Kit is designed to replace BMW 11111735525 for the M50/M52/S50/S52 engines that were used in a variety of BMW models. One significant advantage of these main studs is their ability to prevent main cap walk, which can occur when the main caps shift or move out of position, potentially causing damage to the engine. In addition, ARP Main Studs can safeguard the threads of your engine block, providing an extra layer of protection against potential damage. When opting for main studs instead of factory bolts, it's important to note that the engine builder should mic the bores. Using studs may require a line hone to ensure proper fitment and alignment. A line hone is a machining process that can be used to resize and reshape the main bearing bores, ensuring that they are perfectly round and concentric. This is crucial for ensuring proper oil clearance and preventing premature bearing wear. By mic'ing the bores and performing a line hone if necessary, engine builders can ensure that the main studs are installed correctly and that the engine will perform reliably and at its best. Installation Instructions: To ensure accurate torque readings and proper thread engagement, thoroughly clean all threads in the engine block. If necessary, use an ARP chaser to chase the threads. Before installing any hardware, carefully inspect and clean it for defects, shipping damage, and proper fit, length, and dimension. Gently screw the main studs into the engine block by hand until they are snug. Install the main caps, checking for any binding or misalignment. Apply ARP Ultra-torque fastener assembly lubricant to the threads of the studs, nuts, and washers. Install the washers and nuts onto the studs and tighten them by hand. It is highly recommended to use the ARP Ultra-torque fastener assembly lubricant provided with the kit, as it provides consistent clamping force and reduces friction on the studs. Do not use motor oil or other low-quality lubricants. PRELOAD (TORQUE) RECOMMENDATIONS 7. Following the manufacturer-recommended torque sequence tighten the nuts in steps 1-3 Step 1: Tighten to 20 ft-lbs. Step 2: Tighten to 40 ft-lbs. Step 3: Tighten to 60 ft-lbs. With the included ARP Ultra-Torque fastener assembly lubricant

Show More Show Less

ARP Ultra-Torque Fastener Assembly Lubricant (Select Your Size) ...

T#:338571

Part#: TMS1733

In Stock

Starting at $ 1.99 USD

Add to Wish List

Starting at $ 1.99 USD

Add to Wish List

If you are using a premium fastener, such as the ARP brand rod bolts, head bolts, or main bolts, then you will want this assembly lube. Made to be used to precisely duplicate all ARP fastener preload specifications.

Show More Show Less

Project Cars

SELECT YOUR BMW

BMW Internal Engine Parts for BMW 3 Series E46 (1999-2005)

Sub-Categories

ARP Connecting Rod Bolt Set - S54 (M10, 02/2003- Production) ...

ARP Connecting Rod Bolt Kit - M52, M54B30, N20, N26, N54, N55, B46, B...

ARP Steel Block Head Stud Kit for M50/M52 & S50/S52 (US Spec) ...

ARP Connecting Rod Bolt Kit - Early S54 - E46 M3, MZ3 (M11x47mm Size)...

ARP S54 Head Stud Kit (E46M3 / MZ3 / MZ4)

ARP Connecting Rod Bolt Kit - E36 M3 S50/S52 (US only), E46 323/325 ...

ARP Main Stud Kit for S54 (E46M3 & Z4M)

Main Stud Kit - M50/M52/S50/S52

ARP Ultra-Torque Fastener Assembly Lubricant (Select Your Size) ...

Select Vehicle

Purpose

Category

Brand

Price

Shipping

Narrow Results