Packaged by Turner BMW Suspension Parts for BMW 3 Series E46 (1999-2005)

For all 2001 to 2005 325xi and 330xi. For convenience, we have assembled this bushing carrier bracket kit, to save you time when changing our control arm bushings. It includes two bushing carriers with pre-installed bushings (one left, one right) and mounting bolts.

 These bushing brackets fit all 2001, 2002, 2003, 2004, and 2005 model BMW 325xi and 330xi.

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Front Control Arms
Front Control Arm Bushings

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Control Arms & Bushings
Outer Tie Rods
Sway Bar End Links
Upper Strut Mounts & Reinforcement Plates

The E46 3-series can really benefit from a slightly firmer suspension. The stock shock and spring package is a bit too soft and mushy with a lot of bodyroll. Even the factory sport suspension was a marginal improvement. If you have been left wanting more from your stock suspension, this is the perfect upgrade. In this E46 shock and spring package we paired H&R Sport springs with a set of Bilstein sport shocks and struts to deliver a package with near-stock levels of comfort but with stiffer springs that improve handling and lower the ride height for better aesthetics.

H&R Sport springs lower the ride height by up to 1.4" in front and .75" in the back and stiffens the spring rate. Both combine to lower the car's center of gravity and reduce the amount of bodyroll in corners. The springs are progressive rate so their initial stiffness is actually very compliant and it becomes stiffer as the spring is compressed. This is great for street cars that see bumps and potholes where suspension compliance is key. Overall, they are about 30% stiffer than the stock original springs.

We use Bilstein Sport shocks as the dampers and they feature Bilstein's patented and innovative valving system. With this system, small bumps and impacts are absorbed as they should be. But the shocks stiffen for cornering and other suspension motions. It's the best of both worlds as the shock self-adjusts based on suspension motion. These fit with the stock strut and shock mounts, making for an easy and clean install.

Ride height varies by stock suspension:

E46 standard suspension: F: -1.4: / R: -0.75"
E46 sport suspension: F: -0.75" / R: -0.25"

Parts list:

• 1 set - H&R Sport Springs (29485 or 29484)
• 1 - Bilstein Left Front Sport strut (35-115106)
• 1 - Bilstein Right Front Sport strut (35-115113)
• 1 pair - Bilstein Rear Sport Shocks (24-027250)

This item fits the following BMWs:
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci sedans and coupes

The perfect upgrade for any E46, this finned differential cover increases cooling to the rear differential to prevent over heating and possible damage. This is a complete kit including fluid and drain plugs.

Includes the following

• Aluminum finned differential cover
• Drain & fill plug with sealing o-ring
• 2 Quarts of Redline 75w90

This package allows you to build your own rear bushing package to cover the parts you want to replace. As these cars age, they require a number of suspension bushings to be replaced. Bushing replacement not only keeps the car in its top form, it also makes the car safer. Depending on the work, it may be logical to replace all of the bushings in the rear suspension (there are 19 total). This is especially true if you are pulling the subframe out to do the floor reinforcement or if you're doing a diff install. Turner Motorsport is a big believer in using rubber bushings for street cars (with the exception of solid subframe mounts, see further below). Urethanes, Delrin, or aluminum are generally good for reducing compliance and limiting deflection - attributes that don't really work well on roads filled with potholes, railroad crossings, cracks, and expansion joints. The rubber bushings maintain the factory ride/handling traits that won the M3 praise all over the world. Every bushing will need maintenance or replacement at some point and rubber has proven to last the longest and need less maintenance than anything else, even urethane. And unless competitive driving is your goal, the harder materials are only a gimmick.

Any major overhaul of the rear suspension should include new subframe mounts. The worn rubber mounts contribute to rear subframe-floor failure when the deflection in the mount is transferred to the chassis. Rubber mounts are only OK for street cars that don't see aggressive driving, autocross, or track use. For any enthusiastic driving, we strongly recommend our solid aluminum subframe mounts even on the street. They have zero deflection and will not contribute to rear floor failures. And if you leave rubber in the rest of the suspension your ride comfort will not suffer.

Individual Item Descriptions:

• Trailing Arm Bushings and Limiters (33322228153 and TSU9990001) - our OEM rubber replacement trailing arm bushings (RTABs) are a perfect fit and help maintain rear toe alignment. The Limiters prevent premature bushing wear.
• Rear Inner Control Arm Bushings (upper 33321092247 and lower 33326770824) - new stock inner rubber bushings for the upper spring arm and the lower camber arm. These do not wear out very quickly but should be replaced as a 'While you're in there...' job.
• Rear Outer Control Arm Bushings (upper and lower) (33326775551) - new stock outer ball joints for the upper spring arm and the lower camber arm. These are the standard ball joint design and last a very long time. Check for play with a pry bar and replace as needed.
• Rear Shock Mounts - Choose from several types of RSM upgrades. If your mounts have not been replaced in the last 40,000 miles, now is the perfect time. Skip this option if you recently replaced mounts or already have an upgraded mount.
• Differential mounts (33172282484 and 33112282482) - Now is a great time to replace the front rubber-isolated mount. This is another low-wear mount but it can be changed easily, and is a low cost item. The rear mounts are in the aluminum differential cover and BMW only sells them with it. Solid diff mounts are streetable with only a minimal increase in NVH.
• Rear subframe mounts (33312283573, 33312283574, and 33312283419 x 2) - The heart of the rear suspension, the subframe (or carrier) mounts located the entire rear suspension to the car. There are four mounts in total and bolt up into the rear floor. Worn subframe mounts are one of the leading contributors to rear floor-subframe failure. As the mounts flex, so does the sheetmetal of the chassis, which will fatigue the sheetmetal and crack the spot welds. Therefore, replacement of the subframe mounts is critical and a must when doing the subframe reinforcement or repair. Solid aluminum mounts are streetable with no increase in NVH.

This item fits the following BMWs:
2001-2006 E46 BMW M3 M3 CSL

This package allows you to build your own rear bushing package to cover the parts you want to replace. As these cars age, they require a number of suspension bushings to be replaced. Bushing replacement not only keeps the car in its top form, it also makes the car safer. Depending on the work, it may be logical to replace all of the bushings in the rear suspension (there are 19 total). This is especially true if you are pulling the subframe out to do the floor reinforcement or if you're doing a diff install. Turner Motorsport is a big believer in using rubber bushings for street cars (with the exception of solid subframe mounts, see further below). Urethanes, Delrin, or aluminum are generally good for reducing compliance and limiting deflection - attributes that don't really work well on roads filled with potholes, railroad crossings, cracks, and expansion joints. The rubber bushings maintain the factory ride/handling traits that won the E46 praise all over the world. Every bushing will need maintenance or replacement at some point and rubber has proven to last the longest and need less maintenance than anything else, even urethane. And unless competitive driving is your goal, the harder materials are only a gimmick.

Any major overhaul of the rear suspension should include new subframe mounts. The worn rubber mounts contribute to rear subframe-floor failure when the deflection in the mount is transferred to the chassis. Rubber mounts are only OK for street cars that don't see aggressive driving, autocross, or track use. For any enthusiastic driving, we strongly recommend our solid aluminum subframe mounts even on the street. They have zero deflection and will not contribute to rear floor failures. And if you leave rubber in the rest of the suspension your ride comfort will not suffer.

Individual Item Descriptions:

• Trailing Arm Bushings and Limiters (33322228153 and TSU9990001) - our OEM rubber replacement trailing arm bushings (RTABs) are a perfect fit and help maintain rear toe alignment. The Limiters prevent premature bushing wear.
• Rear Inner Control Arm Bushings (upper 33321092247 and lower 33326770824) - new stock inner rubber bushings for the upper spring arm and the lower camber arm. These do not wear out very quickly but should be replaced as a 'While you're in there...' job.
• Rear Outer Control Arm Bushings (upper and lower) (33326775551) - new stock outer ball joints for the upper spring arm and the lower camber arm. These are the standard ball joint design and last a very long time. Check for play with a pry bar and replace as needed.
• Rear Shock Mounts - Choose from several types of RSM upgrades. If your mounts have not been replaced in the last 40,000 miles, now is the perfect time. Skip this option if you recently replaced mounts or already have an upgraded mount.
• Differential mounts (33176770788 and 33176751808) - Now is a great time to replace the rubber-isolated mounts. This is another low-wear mount but it can be changed easily, and is a low cost item. Solid diff mounts are streetable with only a minimal increase in NVH.
• Rear subframe mounts (33316770783, 33316770784, 33316770781 x 2) - The heart of the rear suspension, the subframe (or carrier) mounts located the entire rear suspension to the car. There are four mounts in total and bolt up into the rear floor. Worn subframe mounts are one of the leading contributors to rear floor-subframe failure. As the mounts flex, so does the sheetmetal of the chassis, which will fatigue the sheetmetal and crack the spot welds. Therefore, replacement of the subframe mounts is critical and a must when doing the subframe reinforcement or repair. Solid aluminum mounts are streetable with no increase in NVH.

This item fits the following BMWs:
1999-2006 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi

This package covers the front control arms and bushings on the 2001-2005 E46 325Xi and 330Xi. These cars use a unique front suspension but the principle design and downside, is the same as almost all of the BMW 3-series since 1984. The inner and outer ball joints see a lot of wear as they are constantly in motion. With the heavy front end of the 4WD Xi, these components need frequent inspection and replacement. When the bushings and ball joints fail, the front end can shimmy and feel loose through the steering wheel. Excess play in the rubber bushings can cause alignment problems and sloppy steering. There is usually a knocking or clunking sound to further annoy you. We've assembled thispackage to replace everything on both front control arms and restore your BMW's exceptional driving dynamics. All parts are OEM Boge, Lemforder, or Original BMW to maintain the highest quality standard.

This kit includes the following parts:

• LEFT FRONT CONTROL ARM, part# 31126758533 / 31 12 6 758 533
• RIGHT FRONT CONTROL ARM, part# 31126758534 / 31 12 6 758 534
• CONTROL ARM BUSHINGS (pair), part# 31129063163 / 31 12 9 063 163
• LEFT FRONT INNER BALL JOINT, part# 31126756695 / 31 12 6 756 695
• RIGHT FRONT INNER BALL JOINT, part# 31126756696 / 31 12 6 756 696

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 1 kit replaces:

Rear Trailing Arm Ball Joint
Rear Control Arm Bushings
Rear Reinforcement Plate
Rear Shock Mounts & Gaskets
New Hardware

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Control Arm Bushings
Trailing Arm Bushings
Sway Bar End Links
Rear Shock Mounts & Reinforcement Plates
Subframe Bushings
RTAB Limiters
Diff Bushings
Hardware

Eliminate the most common sources of suspension slop with our all new Turner Suspension Refresh Kits that feature only OEM parts! We do not include any "cheap parts" in our refresh kits to ensure long-lasting reliability and noise-free suspension.

This Level 2 kit replaces:

Front Strut Mounts & Reinforcements
Control Arms & Bushings
Outer Tie Rods
Sway Bar End Links