BMW Suspension Parts for BMW 3 Series E46 (1999-2005)

The E36/E46 rear trailing arm bushings (RTABs) wear out faster than any other bushing on the car. Worn RTAB will cause excessive toe alignment change and give a 'loose' or 'floaty' feeling in the rear handling. One of the reasons for this is that they over-extend during motion, stretching and twisting the rubber in all directions. These shims sit on either side of the bushing and limit the amount of extension from the bushing. Not only will you get more life from your RTAB but these will help stiffen the bushing during cornering. But during normal driving you will still have all of the comfort of the stock rubber bushings. These part about these bushings is how easy they are to install - simply slide them in place during your bushing install. They can be added to pre-installed bushings too by dropping the trailing arm and removing the cage around the bushing.

Works with stock rubber bushings only (not urethane or Delrin).

Our renowned TMS adjustable front sway bar / swaybar links for BMWs are now available in custom lengths, making them easy to order for any aftermarket or custom suspension setups. Simply measure for your ideal link length, and order the links with the best length range (below). Each sway bar link has a 10mm diameter mounting pin/stud, which is the typical factory/stock size for a universal fitment. These are sold by the pair, and each set includes two matching sway bar end links.

These end links offer the quiet operation and long life of "stock" BMW end links, but with the strength and adjustability of rod-end style sway bar links. These sway bar links can be used on a wide variety of BMWs and aftermarket BMW suspensions. When measuring, please consider that the length ranges of our Custom Adjustable end links are measured from the center to center on the end link mounting stud / pin, as shown in our diagram.

Note for E9X M3: the unique mounting on the M3 strut requires a set of our adapter seats (#TSU9912AF9). You can add them with your links from the menu below.
 

TMS Part#Center to Center (mm)Center to Center (inch)

TSU9912A35155.00mm - 170.00mm6.10" - 6.69"

TSU9912A40170.00mm - 185.00mm6.69" - 7.28"

TSU9912A45180.00mm - 195.00mm7.08" - 7.67"

TSU9912A50190.00mm - 205.00mm7.48" - 8.07"

TSU9912A55207.00mm - 222.00mm8.15" - 8.74"

TSU9912AF1220.00mm - 235.00mm8.66" - 9.25"

TSU9912A70240.00mm - 255.00mm9.45" - 10.04"

TSU4612AF3250.00mm - 265.00mm9.84" - 10.43"

TSU9912A80261.00mm - 276.00mm10.28" - 10.87"

TSU5012AF8280.00mm - 295.00mm11.02" - 11.61"

TSU9912A95290.00mm - 305.00mm11.42" - 12.00"

TSU9912110320.00mm - 335.00mm12.59" - 13.19"

TSU9912115330.00mm - 345.00mm12.99" - 13.58"

TSU9912130362.00mm - 377.00mm14.25" - 14.84"

TSU9912135370.00mm - 385.00mm14.57" - 15.16"

TSU9912140381.00mm - 396.00mm15.00" - 15.60"

TSU9912145389.00mm - 404.00mm15.31" - 15.91"

Please select your length below. 

Rear Axle Carrier Panel (RACP) failure is a well-documented issue that plagues all BMW E46 models. Due to thin sheet metal mounting, the forces applied during cornering, acceleration, and braking create stress fractures in the carrier panel, resulting in large cracks or breaks that risk the structural integrity of your chassis. To fix this issue, many enthusiasts opt to install weld-in reinforcement plates on the underside of the RACP. While this remedies the formation of additional stress cracks and adds rigidity to failure-prone areas, it does not prevent the entire carrier panel from flexing during high-performance driving.

Our all-new Rear Subframe Reinforcement Brace is engineered to add structure to the E46's rear chassis under high-stress conditions, eliminating the common weak points in the RACP while providing the confidence you need for performance driving. Don't let chassis flex limit your car’s potential—upgrade your E46 with the Turner Motorsport Rear Subframe Reinforcement Brace today!

How It Works:

During performance driving, the Rear Axle Carrier Panel (RACP) must react the forces of longitudinal and lateral accelerations. During forward acceleration, the differential transmits torque through the subframe to the RACP, forcing the rearmost subframe mounting points downward. This downward movement flexes the carrier panel, reducing its ability to handle torque efficiently. By linking the rearmost subframe mounting points to the rear shock towers, downward flex is restricted, resulting in improved torque transfer and stability. Alternatively, high-grip cornering generates lateral acceleration (side-to-side) forces across the RACP. Similar to how a rear strut brace functions, connecting the rear shock towers helps to counteract these forces. Adding the subframe to this connection further reduces lateral loads, eliminating side-to-side flex and enhancing overall stability.

Features & Design:

Four-Point Triangulated Structure: Links the rearmost subframe mounting locations to both rear strut towers for superior load distribution. Enhanced Stability: Reduces lateral and longitudinal RACP flex during acceleration, braking, and cornering. Improved Torque Transfer: Minimizes downward flex of the RACP, ensuring efficient power delivery for enhanced driveability. High-Performance Durability: Heavy-duty steel tube construction ensures lasting support during spirited driving, track use, and for vehicles with increased power output. Blue Powdercoat Finish: Offers fantastic corrosion resistance, protection from scuffs and scratches, and a stylish appearance that is sure to complement your performance-centric E46. Underside Reinforcement Compatibility: Designed to work seamlessly alongside our underside RACP reinforcement plates (TDR4675412, T#91). Kit Includes:

Rear Subframe Brace Sedan Subframe Brace Spacers Extended-Length Drill Bit (1/4", 12" Overall Length) High-Speed Drill Bit (12.5mm, 152mm Overall Length) Drill Bit Guide Extended Subframe Bolts Zinc-Plated Steel Hex Nut (2) Installation & Support:

Need installation tips? Our team has assembled a guided start-to-finish installation tutorial, including detailed instructions on drilling and cutting your trunk floor panel for perfect fitment. Click HERE for Installation Instructions

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These E46 fixed camber plates are designed from knowledge gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. These plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to between -2.5° to -3.0°, depending on each individual car. While ride height is increased by 1/4", the benefit of these plates far outweighs the minor ride height increase. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Material has also been added to increase surface contact area therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal in many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class. These are a simple bolt on part for all E46 except the xi and M3 models.

Instructions for Turner E46 Front Fixed Camber Plates

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

Worn rubber differential mounts will lead to the differential twisting and shifting around in the rear subframe. Not only will this be noisy but it's bad for driver confidence and bad for the chassis as well. Even on fresh rubber bushings the differential has deflection and twist, especially if the car has been modified for more torque. Since the differential is centrally mounted in the rear subframe, with all suspension mounts interconnected, a differential with too much deflection will affect handling and could even damage the rear subframe.

These 88A urethane E46 diff mounts are much stiffer than stock but still not as solid as our Turner aluminum/Delrin bushings. This set will resist twisting much better than the stock rubber mounts. Included are the two front diff mounts and the rear mount in the cover.

BMW E36 E46 KW Replacement Front End Link - Each is crafted to enhance the suspension performance of BMW E36 and E46 models, ensuring precision and stability on both road and track. Built with high-quality materials to meet KW’s exacting standards, this replacement front end link is designed to provide consistent handling and improved durability, especially when paired with KW coilovers or other suspension upgrades.

• Optimized for BMW E36 and E46 models, ensuring a perfect fit and reliable performance
• Durable construction withstands daily driving and track conditions
• Reduces unwanted suspension movement, delivering more accurate handling and stability
• Ideal for KW coilover setups or other aftermarket suspension modifications
• Quick, straightforward installation for minimal downtime

Control arm bushings play a key role in connecting the wheels to the chassis of the vehicle. Tasked with keeping suspension geometry in check while absorbing noise, vibration, and harshness (NVH) factory rubber bushings were engineered to provide a balance of comfort and control. As a factory bushing ages, it becomes brittle and begins to harden. When this happens the bushing will actually shrink and allow excess play in the suspension joint. This is typically felt by a sudden jerk forward after the car comes to a stop and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushing with a full polyurethane unit or using a bushing insert, this play is eliminated since the suspension joint is being supported by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver.

Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:

All 1999-2006 E46
All 2002-2008 E85 Z4

Upgrade your BMW's suspension with ECS Tuning Adjustable Sway Bar End Links, designed to provide up to 60mm (2.36") of adjustability. These end links allow you to eliminate sway bar preload or fine-tune it for specific racing needs and corner balancing. When installed, they improve drivetrain clearance and enhance sway bar responsiveness by reducing deflection, ensuring superior handling. Perfect for lowered vehicles using springs, coilovers, or air-ride suspension systems, these adjustable sway bar end links allow you to remove unwanted preload caused by changes in the center-to-center distance between sway bar mounting points. By adjusting the end links to a neutral position, you eliminate sway bar preload, enhancing suspension performance in various driving conditions.

The main body of the ECS Sway Bar End Links is crafted from strong, lightweight 6061-T6 billet aluminum and anodized red for superior corrosion resistance. Featuring left and right-hand threaded center sections and machined hex wrench fittings, these end links allow for quick and easy on-the-car adjustments. Zinc-plated hardware ensures secure and lasting adjustments, while the heavy-duty ball joint ends come with weather-resistant rubber boots and stainless steel wire retainers, providing superior protection against salt, rain, and ozone for extended durability. Each kit also includes zinc-plated Nyloc nuts and hardened steel washers for secure installation and improved contact surface on the sway bar.

These end links are designed, engineered, and rigorously tested by ECS Tuning to ensure the highest quality. Whether you have a lowered or stock suspension, these adjustable sway bar end links are the perfect upgrade, offering a high-quality, heavy-duty replacement that fits your specific needs.

Features:

Range of Adjustment: 255mm (10") to 315mm (12.4") 6061-T6 Billet Aluminum Construction: Red anodized for superior corrosion resistance Zinc-Plated Hardware: Provides durability and superior corrosion protection Right and Left-Hand Threaded Center Sections: Quick and simple on-the-car adjustments Heavy-Duty Ball Joints (M10x1.5): Weather-resistant rubber boots and stainless steel wire retainers for long-lasting durability NOTE: If you've modified your vehicle's suspension with aftermarket struts or coilovers, the mounting location for the sway bar end link may have moved. To confirm fitment with our adjustable end links, please measure the distance between the sway bar and the mounting location on the strut body with the vehicle at ride height and confirm that it is within the 255 mm - 315mm range of adjustment.

Tasked with keeping the vehicles rear end firmly mounted while absorbing noise, vibration, and harshness (NVH) factory rubber subframe bushings were engineered to provide a balance of control while keeping the ride quality soft and supple. As a factory bushings age, they become brittle and begin to harden. When this happens the bushing will actually shrink and allow excess play, or movement in the subframe. This is typically felt by a sudden jerk or "thunking" noise under acceleration and is a leading cause of "sloppy" or "loose" suspension feel. By replacing the bushings with full polyurethane this play is eliminated since the subframe is being held in place by a much stiffer material that will not harden or shrink over time. Additionally, the inherent stiffness of the urethane material translates body forces much more directly. This means steering and acceleration inputs from the driver are effectively transferred to the wheels and vital road information is transmitted properly from the wheels to the driver. 

Engineered to perform, Powerflex performance polyurethane bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved steering feel, turn in, more responsive handling and overall improved chassis composure with Powerflex performance polyurethane control arm bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.

Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

Our experience with spherical front control arm ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).  We wanted to offer e30, e36, and e46 owners similar levels of handling precision and control for the track and street, but weren’t satisfied with the other options out there.  Instead of a Delrin bushing or unsealed spherical bearing alone, we selected an oversized sealed greaseable spherical monoball to offer unparalleled durability and precision, but designed a Delrin adapter sleeve to help isolate the added noise, vibration, and harshness that a full solid monoball bearing will have. While race-ready, our hybrid Delrin/monoball control arm bearings are more at home on the street than other kits that are advertised as “race-only” bearings. We did extensive street, autocross, and track testing to ensure the spherical bearing used in this bushing design excelled in each setting.

The stock rubber bushings, even those found in the M3, allow significant fore/aft movement of the front wheels to help absorb road impacts, especially when being pushed hard.  This soft flexible design maximizes daily driving comfort, but also allows considerable alignment change.  This unwanted deflection stands between you and a crisp, confidence-inspiring driving experience.  The advantage of a monoball bearing is that it will not deflect under load, eliminating all unwanted deflection while still allowing complete freedom of movement in the desired angles. What you get is superior steering precision with better handling from more consistent alignment and direct braking feedback, with exceptional service life.  Thanks to the Delrin insert and double lip seals, there's none of the extra noise or reduced service life often found on other spherical bearings.

In short, if you're seeking front control arm bushings that offer precise, predictable handling, crisper braking feel, with a long service life free from noise - look no further. We have you covered.

Watch to learn more about Turner Monoball Bushings

Features:

Bearing housing

• Precision CNC machined from 6061-T6 blue anodized aluminum with a pre-installed grease fitting and grease distribution channels making this a serviceable design
• Knurled for smooth press fit in a wide variance in “lollipop” dimensions

Bearing

• A high quality greaseable double lip sealed bearing with Delrin® inserts. Delrin® was chosen for its durability under pressure, while still soft enough to create a perfect play-free fitment on the control arm.
• Replaceable for infinite service life - no need to replace the entire mount in the event a bearing happens to fail.

Includes new hardware. Grease before installation and with each oil service with high quality Moly grease for maximum service life. Need a grease fitting tool?

Installation is relatively easy - see our instructions here. 

This item fits the following BMWs: 
2001-2006 E46 BMW M3 

Differential bushings are responsible for keeping the differential in solid alignment while dampening drivetrain vibration. While OE rubber bushings are fine when they are new from the factory, aged and worn out rubber bushings create a multitude of issues that can range from annoying to dangerous. As a factory bushing ages, it begins to harden and become brittle. When this happens the bushing will actually shrink and allow for movement at the differential mounting point. At this point, the differential is free to shift under load causing a noticeable clunking noise under acceleration and deceleration and massively increasing the stress on the driveshaft and axles. Manual transmissions suffer the worst from this as it can make shifting difficult since the differential will shift when the clutch is engaged and disengaged.

By replacing these bushings with full polyurethane, the movement is eliminated since the mounting point is supported by a much stiffer material that will not harden or shrink over time. This means less stress on the driveshaft and axles and greater longevity of supporting components. 

Powerflex Black Series bushings are the ultimate in track and race bushings. Featuring 95A durometer polyurethane, Black Series bushings are 25% stiffer than street bushings. Engineered to perform, Powerflex performance polyurethane control arm bushings offer a supreme level of control, while still providing enough comfort for the street, with advanced polyurethane that reduces NVH that often accompanies lesser bushings. Expect improved acceleration response, more direct shifting feel and overall improved drivetrain composure with Powerflex performance polyurethane bushings.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

This part fits the following BMWs:
2001 - 2006 E46 M3

Sway bars transmit cornering forces from the outside wheels to the inside wheels, helping to keep the vehicle flat during cornering. This in turn reduces body roll and improves the driver's cornering confidence. OEM rubber sway bar bushings are designed with comfort in mind, allowing the sway bar to articulate while permitting additional movement, leading to less-than-ideal bar retention and causes unnecessary body roll.

Powerflex polyurethane sway bar bushings are firmer than factory rubber bushings, reducing body roll and keeping sway bars in check. Polyurethane bushings won't slop around like OEM bushings, allowing sway bars to function at their fullest potential.

Poweflex is a leading manufacturer of aftermarket suspension bushings. Using state of the art design and manufacturing, all replacement bushings are engineered to out-perform and out-last the ones that came in the car. Each line of bushings is meticulously tested and then re-tested to ensure perfect fitment and enduring quality through the life of the vehicle. A full lifetime warranty backs every one of their products and demonstrates the level of confidence and commitment Powerflex has to their customers. 

NOTE: For use with factory 21.5mm sway bar only