BMW Suspension Parts for BMW 3 Series E46 (1999-2005)

The B16 PSS10 coilovers offer a stiffer spring rate than stock and a lower ride height for less bodyroll and better handling. These are among the easiest coil over kits on the market - no special mounts required (works with stock mounts and sway bar links), larger adjustment knob allows for easy shock damping changes, and coil over spanner wrenches included for easy height changes. Bilstein backs up their technology with a limited lifetime warranty. TUV approved for fitment, safety, and quality!

Bilstein's monotube shock dampers in the PSS10 offer 10 precise settings for compression and rebound. A new setting is just a click away, allowing you to set a ride and handling combination that works for your setting. Instead of offering too many shock settings that you're never going to use, Bilstein has chosen ten optimal damping curves from a smooth street setting (P10) to an ultra-stiff track-only setup (P1). Shock changes are made from an easy-to-use over-sized adjuster knob.

Ride height adjustments are done from perches that ride on each shock body, which are zinc coated for excellent wear and corrosion resistance. You can set the ride height between 0.5 to 1.3 inches lower than stock ride height. Springs are progressively rated so their initial compression rating is quite soft and then becomes stiffer as the spring compresses. These are stiffer than most coil over kit manufacturers and the results of Bilstein's extensive testing on the German Nurgburgring and Autobahn.

The fitment of these is just like a standard shock and spring package. The front struts and rear shocks are compatible with the stock strut and shock mounts. You can re-use your own or choose a mount with additional features. Because the Bilstein design keeps the sway bar tab in the original location, you can re-use the stock sway bar links. Using the stock mounts keeps the cost and complexity down and allows for TUV certification. You can also be assured of the stock mount's quiet and long-lasting performance. The assembly of the front strut is the same as a the factory strut. In the rear, ride height is made by an adjustable spring perch that sits under the rear spring. Install instructions and diagrams included.

If you're looking for a supremely capable and high quality suspension, then look no further than the Bilstein PSS10. It combines all of the best German engineering with real-world development, and a lifetime warranty.

Fitment note: this system works only on cars not equipped with the factory EDC electronically adjustable shocks.

Featuring:

• Largest available piston diameter for greater sensitivity and precise control.
• Patented digressive piston head design and deflective valving instantly reacts to changing road conditions.
• 10-way adjustable dampening knobs that "click" from soft to hard with no tools or jacking required.
• Monotube design dissipates heat more effectively than a twin tube shock for cooler, more efficient operation and longer life.
• Weather resistant coating to resist oxidization, and ensure long life.
• Lighter weight reduces wear and tear on suspension components.
• Wrenches to adjust front and rear ride height included!

This item fits the following BMWs:
2001-2006 E46 BMW M3

The Bilstein B14 PSS Suspension allows adjustable vehicle ride height without the expense of a fully adjustable damping system. This system features both coilover and standard mono-tube gas pressure shock or struts with performance level valving for application specific, progressive rate coil springs.
The product benefits at a glance:

• Threaded body adjustable range of 20 mm
• Lowering of approx. 30-50 mm at front and rear
• Road-tested and fine-tuned by BILSTEIN ride engineers, under extreme motorsports conditions
• Aluminum Spring plates and lock nuts
• Surface coating using Triple-C-Technology for long-lasting corrosion resistance
• Round threads for easy adjustment
• Quality sport springs made from highly durable material
• Gas pressure technology

BILSTEIN monotube technology, made in Germany

adj. -1.0"-1.75" / adj. -1.0"-1.75"

Not for cars with EDC

Alternate Bilstein part number: 47-126848.

This coilover kit fits the following BMWs:
1999-2005 E46 BMW 323i 325i 328i 330i 4 door sedan & wagon (RWD models only)
2000-2006 E46 BMW 323Ci 325Ci 328Ci 330Ci (coupe & convertible)

This ball joint is used for the upper rear trailing arm bushing on ALL E36, E46, E83 X3, and E85 Z4 cars. BMW also used it as the lower bushing on most M cars. It makes a great upgrade on all non-M cars where BMW used a rubber bushing at the lower position.

This sealed ball joint is one of the best things about the rear suspension - it functions extremely well and lasts a long time. And it can be used as a replacement for the existing bushing without any further modification. The non-M cars used a solid rubber bushing for the lower arm (camber arm, wishbone) which does not last very long and relies on bushing deflection (twist) during suspension motions. The ball joint inside the upgraded design is much more effective during this suspension movements as it does not bind or deflect. And because it's sealed with rubber it will last a long time and remain quiet and maintenance free. Most customers report that after installing or "upgrading" to these bushings the rear end of their car felt much more stable.

Price is per bushing. Left/Right and Upper/Lower are the same part.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2004-2010 E83 BMW X3 2.5i X3 3.0i X3 3.0si
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Our sealed Monoball Rear Trailing Arm Bushings (RTAB) are the best solution for completely eliminating deflection and unwanted toe changes on the rear of the E36, E46, and Z4. While rubber and urethane bushings flex during load, the toe can change widely giving you nervous and unpredictable handling. These RTABs have a solid aluminum housing with a high-quality sealed OE bearing. These bushings were developed from years of competition use in various racing and HPDE events. There is simply no better RTAB unless your racing class rules prohibit the use of mono or spherical bearings.

The rear trailing arm bushings take a lot of abuse from acclerating, braking and cornering. The stock rubber bushings are just not up to the task of keeping rear wheel alignment in spec for very long, especially if you have upgraded to stickier tires and a better suspension. The pliable rubber flexes and twists which slows down reaction time and leaves you with a car that feels nervous and 'tail happy'. Urethane helps to control the alignment but issues with fitment, maintenance, and longevity keep us from recommending urethane on anything but a street car. We also offer a Delrin RTAB for cars that must conform to certain racing class rules. These sealed spherical bearings are the best at controlling rear toe alignment.

Our aluminum RTABs are very well made - high grade aluminum alloy and steel CNC'd out of a billet by an ISO 9001 certified manufacturer, each component is either hardcoated or nickel plated. While multiple manufacturers offer two piece designs, our research showed that a one piece bushing is a better design featuring a sealed bearing to keep contaminants out extending the life of the bearing.

Features:

Key Benefits:

• Rear Trailing Arm Monoball eliminates unwanted deflection, maintaining alignment settings and minimizing wheel hop.
• Allows full rear trailing arm articulation for low friction movement and eliminates binding found in rubber and poly bushings.
• Completely streetable: utilizes an OES Lemforder brand sealed, greased ball joint for an extremely long service life with no increase to NVH.

Design Features:

• Housing: Billet CNC 6061-T6 aluminum, type II anodized for exceptional durability and corrosion resistance
• Bearing: OE Mercedes/lemforder 2043520027 Sealed ball joint
• Bearing inserts: CNC machined 303 stainless steel.
• Rebuildable

Clickhere for installation instructions.

This item fits the following BMWs:
1992-1998 E36 BMW 318i 318is 318ic 323is 323ic 325i 325is 325ic 328i 328is 328ic M3
1999-2005 E46 BMW 323i 323ci 325i 325ci 325xi 328i 328ci 330i 330ci 330xi M3
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

This is the standard front sway bar / swaybar link for BMW E46 and E85 Z4. It connects the sway bar to the strut. If you hear front end noise when going over bumps while turning we recommend you check these. Alternate BMW Part#31356780847 Sold individually

Sway bar end links connect the swaybar to the rest of the suspension, preventing body roll and keeping everything in line in tight turns. This exposes these links to a high amount of stress and pressure, often leading to split bushings and sloppy body control and knocking noises. OEM Lemförder sway bar links are the perfect option to restore body control and eliminate knocking noises.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci M3 - Sorry not for Xi Models!
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Click here for installation instructions.

These camber plates are perfect for the enthusiast owner who wants a high quality design with a motorsports background. Knowing a full race kit on the street is not often the best option, we took the best features from the Race Camber Plates and incorporated them into a fresh Street design -

• preserves the correct E46 M3 geometry
• separate sliding camber and caster adjustments
• maximum shock travel
• light weight
• durable materials
• large surface area
• ease of use

The Turner E46 M3 Street Camber Plates are the most advanced design on the market. These are designed specifically for the E46 M3 - no shortcuts or cookie-cutter components. We started with a fresh design to make these very user friendly and easy to install and set up. The E46 M3 front suspension has unique geometry and the strut is mounted at an angle that can put significant side loading on the strut shaft if it's not located properly. The location and angles for the main bearing were carefully engineered to allow the proper motion ratio and strut angles during adjustment. This greatly reduces bending forces on the strut itself which improves performance and longevity. By designing for one chassis we're able to focus on what works best in that application - proper fitment and operation without unnecessary adapters, easy-to-use camber and caster adjustments, and an intelligent modular design.

For street use we added a pliable urethane bushing to absorb vibration and a special base design that works with the factory radial bearing and spring perch. The radial bearing allows the spring to rotate instead of twisting and binding. By re-using the factory radial bearing we can keep the assembled stack height lower for maximized shock travel. It's also a commonly-available item that you can get from any BMW dealer at a low price. All of the things that make it work well in the factory application carry over to our design. You can use our camber plates with a stock sized spring, 60mm, or 2.5" springs. Use your stock spring perch/bearing with stock-sized springs. The 60mm and 2.5" upper spring perches are sold separately. The beauty of our design is that you can use the factory radial bearing with any of these springs.

Another important feature of the Turner Camber Plates is the size of the upper plate. Our plates have a very large surface area to better spread strut forces through the strut tower. A smaller upper plate, like those found on competitor's kits, will localize strut forces and contribute to strut tower deformation ('strut tower mushrooming'). This is a very important feature especially as these cars get older and spend more time on the track. Deformed strut towers are a serious performance and safety concern and our camber plates are properly designed to handle the loads. The factory strut reinforcement plates are not required with our camber plates (but you can use them if you want to).

Since this design is specific to the E46 M3, we can build it with the bare minimum of adapters and extra hardware. This not only cuts down on confusion but makes it easier to assemble and operate. We use the correct-sized bearing for the 16mm strut shaft; no sleeves or bearing adapters required. The original tapered lower mount support and a small stainless steel spacer from our kit are all that's required to install. We have used our camber plates with most of the major strut manufacturers on the market - stock Sachs/Boge, Bilstein, Koni, H&R, ST, and KW. Our camber plates work with any strut that is designed to accept the factory strut mount.

Click here for installation instructions.

This item fits the following BMWs:
2001-2006 E46 BMW M3

One of the tricks for getting your BMW to handle better is to add negative camber to the front wheels. This will put more of the tire's width in contact with the ground during cornering. With more rubber there is more grip. BMWs typically have less camber in the front to create understeer. But if you're running a stock setup on the track or autocross you are giving up speed and time as the front tires run out of grip sooner than they should.

These E46 fixed camber plates are designed from knowledge gained from our highly successful racing campaigns with the E46 in the Speed World Challenge series. These plates are offset for the best camber and caster combination for racing purposes when using the stock-diameter sized springs. Camber increases to between -2.5° to -3.0°, depending on each individual car. While ride height is increased by 1/4", the benefit of these plates far outweighs the minor ride height increase. The rate of camber change is virtually unaffected throughout the range of suspension travel, reducing the need for other geometry correction. Material has also been added to increase surface contact area therefore reducing the strut tower deformation and increasing the strength of the strut towers. Fixed mount camber plates are legal in many racing and autocross classes. These are the perfect camber solution when adjustable plates are not allowed in your class. These are a simple bolt on part for all E46 except the xi and M3 models.

Instructions for Turner E46 Front Fixed Camber Plates

This item fits the following BMWs:
1999-2005 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci

The front control arm bushings are a key piece of the suspension. They are constantly in motion and take abuse from impacts, potholes, rough roads, and general cornering/wheel motions. To give a quiet and smooth ride, the bushings are made of rubber with a metal sleeve insert. But the rubber can only withstand so much abuse before they become loose and spongy. This results in vibrations and possibly a shimmy when driving. A visual inspection will usually confirm that there is too much flex in the rubber or the rubber has cracked and torn. And if you're installing new control arms, always install new bushings to avoid duplicating labor costs.

This is a replacement stock LEFT FRONT (Driver's side) control arm bushing with the mounting bracket.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
2001-2006 E46 BMW M3

Lemforder
This control arm upgrade was used on the high-performance 330i ZHP Performance Package and offered by BMW as a sport retrofit. These arms are identical dimensions as the regular arms so they are a direct replacement. But they have all metal ball joints instead of plastic or rubber. This means they last a lot longer and are much stronger. We used these in our Grand Am and World Challenge E46 racecars with excellent performance.

Control arms, and their integrated ball joints, are some of the most crucial components on a BMW suspension. The control arms literally control the wheel and suspension as they go through their range of motions. A faulty or worn control arm or ball joint is a very dangerous and potentially life-threatening problem so make sure they are inspected and replaced at regular intervals. For a street-driven car we advise yearly inspection and a full replacement every 3-4 years. For track-driven cars these should be inspected before every event and replaced every two years.

We also recommend replacing the bushings when changing the control arms. The bushings are mounted at the back of the control arm and located the arm to the frame rail on the car. The stock bushings are rubber and will wear out sooner than the control arms themselves. With the control arm off the car now is the perfect time to also replace the bushings.

Lemforder is the original equipment supplier to BMW for these control arms.

OEM Lemförder is an engineering company that focuses on high-quality, precision manufacturing of critical suspension and steering components. Providing exceptionally high quality parts directly to BMW, as well as 50+ other big name automotive companies, such as Mercedes and Audi, their history of reliability and variety of offered parts makes them one of the biggest names for a go-to OEM parts provider. Lemförder parts place an important emphasis on design, production, and assembly, ensuring maximum reliability. They even coat all parts possible with corrosion protection for extended longevity.

As a leading source of high performance BMW parts and accessories since 1993, we at Turner Motorsport are honored to be the go-to supplier for tens of thousands of enthusiasts the world over. With over two decades of parts, service, and racing experience under our belt, we provide only quality performance and replacement parts.  All of our performance parts are those we would (and do!) install and run on our own cars, as well as replacement parts that are Genuine BMW or from OEM manufacturers. We only offer parts we know you can trust to perform!

This item fits the following BMWs:
1999-2006 E46 BMW 323i 323ci 325i 325ci 328i 328ci 330i 330ci
2003-2008 Z4 BMW Z4 2.5i Z4 3.0i Z4 3.0si Z4 M Roadster M Coupe

Our experience with spherical front control arm�ball joints go back to those we designed and used in our IMSA E90 328i and E92 M3 racecars (GS class Champions in 2011).��We wanted to offer e30, e36, and e46 owners similar levels of handling precision and control for the track and street, but weren�t satisfied with the other options out there.� Instead of a Delrin bushing or unsealed spherical bearing alone, we selected an oversized sealed greaseable spherical monoball to offer unparalleled durability and precision, but designed a Delrin adapter sleeve to help isolate the added noise, vibration, and harshness that a full solid monoball bearing will have.�While race-ready,�our hybrid Delrin/monoball control arm bearings are more at home on the street than other kits that are advertised as��race-only� bearings. We did extensive street, autocross, and track testing to ensure the spherical bearing used in this bushing design excelled in each setting.

The stock rubber bushings, even�those found in the M3,�allow significant fore/aft movement of the front wheels to help absorb road impacts, especially when being pushed hard. �This soft flexible design maximizes daily driving comfort, but also allows considerable alignment change.� This unwanted deflection�stands between you and a crisp, confidence-inspiring driving experience. �The advantage of a monoball bearing is that it will not deflect under load, eliminating all unwanted deflection while still allowing�complete freedom of movement�in the desired angles. What you get is superior steering precision with better handling from more consistent alignment�and direct braking feedback, with exceptional service life.� Thanks to the�Delrin insert and double lip seals, there's none of the extra noise or reduced service life�often�found on�other�spherical bearings.

In short, if you're seeking front control arm bushings that offer precise, predictable handling, crisper braking feel, with a long service life free from noise - look no further. We have you covered.

�

Watch to learn more about Turner Monoball Bushings

�

�

Features:

Bearing housing

• Manufactured using 6061-T6 blue anodized aluminum with a pre-installed grease fitting and grease distribution channels making this a serviceable design
• Knurling allows for a wide variance in lollipop dimension, although this particular SKU comes pre-installed, so you won't need to worry about that.�Want to install your own? Click here.�

Bearing

• A high quality greaseable double lip sealed bearing with Delrin� inserts. Delrin� was chosen due to durability�under pressure, while still soft�enough to create a perfect play-free fitment on the control arm.
• Replaceable for infinite service life - no need to replace the entire mount in the event a bearing happens to fail.

Includes new hardware. Grease before installation and with each oil service with high quality Moly grease for maximum service life.�Need a grease fitting tool?

Installation is relatively easy - see our instructions here.�

This item fits the following BMWs:

1999-2006�E46 BMW�323i 323ci 325i 325ci 328i 328ci 330i 330ci�
2003-2008�Z4 BMW�Z4 2.5i Z4 3.0i Z4 3.0si�